View PIC16F722A-EMV_448749.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PIC16F/LF722A/723A Data Sheet
28-Pin Flash Microcontrollers with nanoWatt XLP Technology
2010 Microchip Technology Inc.
DS41417A
Note the following details of the code protection feature on Microchip devices: * * * Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable."
* *
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights.
Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2010, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-60932-120-8
Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified.
DS41417A-page 2
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
28-Pin Flash Microcontrollers with nanoWatt XLP Technology
Devices Included In This Data Sheet:
PIC16F722A/723A Devices: * PIC16F722A * PIC16F723A PIC16LF722A/723A Devices: * PIC16LF722A * PIC16LF723A
Extreme Low-Power Management PIC16LF722A/723A with nanoWatt XLP:
* Sleep Mode: 20 nA * Watchdog Timer: 500 nA * Timer1 Oscillator: 600 nA @ 32 kHz
Analog Features:
* A/D Converter: - 8-bit resolution and up to 14 channels - Conversion available during Sleep - Selectable 1.024/2.048/4.096V voltage reference * On-chip 3.2V Regulator (PIC16F722A/723A devices only)
High-Performance RISC CPU:
* Only 35 Instructions to Learn: - All single-cycle instructions except branches * Operating Speed: - DC - 20 MHz oscillator/clock input - DC - 200 ns instruction cycle * Up to 4K x 14 Words of Flash Program Memory * Up to 192 Bytes of Data Memory (RAM) * Interrupt Capability * 8-Level Deep Hardware Stack * Direct, Indirect and Relative Addressing modes * Processor Read Access to Program Memory * Pinout Compatible to other 28-pin PIC16CXXX and PIC16FXXX Microcontrollers
Peripheral Highlights:
* Up to 24 I/O Pins and 1 Input-only Pin: - High-current source/sink for direct LED drive - Interrupt-on-pin change - Individually programmable weak pull-ups * Timer0: 8-Bit Timer/Counter with 8-Bit Prescaler * Enhanced Timer1: - Dedicated low-power 32 kHz oscillator - 16-bit timer/counter with prescaler - External Gate Input mode with toggle and single shot modes - Interrupt-on-gate completion * Timer2: 8-Bit Timer/Counter with 8-Bit Period Register, Prescaler and Postscaler * Two Capture, Compare, PWM (CCP) Modules: - 16-bit Capture, max. resolution 12.5 ns - 16-bit Compare, max. resolution 200 ns - 10-bit PWM, max. frequency 20 kHz * Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART) * Synchronous Serial Port (SSP): - SPI (Master/Slave) - I2CTM (Slave) with Address Mask * mTouchTM Sensing Oscillator Module: - Up to 16 input channels
Special Microcontroller Features:
* Precision Internal Oscillator: - 16 MHz or 500 kHz operation - Factory calibrated to 1%, typical - Software tunable - Software selectable /1, /2, /4 or /8 divider * 1.8V-5.5V Operation - PIC16F722A/723A * 1.8V-3.6V Operation - PIC16LF722A/723A * Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) * Brown-out Reset (BOR): - Selectable between two trip points - Disable in Sleep option * Programmable Code Protection * In-Circuit Serial ProgrammingTM (ICSPTM) via Two Pins * Multiplexed Master Clear with Pull-up/Input Pin * Industrial and Extended Temperature Range * High-Endurance Flash Cell: - 1,000 write Flash endurance (typical) - Flash retention: > 40 years * Power-Saving Sleep mode
2010 Microchip Technology Inc.
DS41417A-page 3
PIC16F/LF722A/723A
Program Memory Flash (words) 2048 4096 SRAM (bytes) 128 192 8-bit A/D (ch) 11 11 Timers 8/16-bit 2/1 2/1
Device PIC16F722A/ PIC16LF722A PIC16F723A/ PIC16LF723A
I/Os 25 25
Interrupts 12 12
AUSART Yes Yes
CCP 2 2
DS41417A-page 4
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
Pin Diagrams - 28-PIN PDIP/SOIC/SSOP/QFN/UQFN (PIC16F/LF722A/723A)
PDIP, SOIC, SSOP
VPP/MCLR/RE3 VCAP(3)/SS(2)/AN0/RA0 AN1/RA1 AN2/RA2 VREF/AN3/RA3 T0CKI/CPS6/RA4
VCAP(3)/SS(2)/CPS7/AN4/RA5
1 2 3 4
28 27 26 25
RB7/ICSPDAT RB6/ICSPCLK RB5/AN13/CPS5/T1G RB4/AN11/CPS4 RB3/AN9/CPS3/CCP2(1) RB2/AN8/CPS2 RB1/AN10/CPS1 RB0/AN12/CPS0/INT VDD VSS RC7/RX/DT RC6/TX/CK RC5/SDO RC4/SDI/SDA
6 7 8 9 10 11 12 13 14
PIC16LF722A/723A
PIC16F722A/723A
5
24 23 22 21 20 19 18 17 16 15
VSS CLKIN/OSC1/RA7
VCAP(3)/CLKOUT/OSC2/RA6
T1CKI/T1OSO/RC0 CCP2 /T1OSI/RC1 CCP1/RC2 SCL/SCK/RC3
(1)
RA1/AN1 RA0/AN0/SS(2)/VCAP(3)
QFN, UQFN
28 27 26 25 24 23 22
RE3/MCLR/VPP RB7/ICSPDAT RB6/ICSPCLK RB5/AN13/CPS5/T1G RB4/AN11/CPS4
AN2/RA2 VREF/AN3/RA3 T0CKI/CPS6/RA4 VCAP(3)/SS(2)/CPS7/AN4/RA5 VSS CLKIN/OSC1/RA7 VCAP(3)/CLKOUT/OSC2/RA6
1 2 3 PIC16F722A/723A 4 PIC16LF722A/723A 5 6 7 8 9 10 11 12 13 14
21 20 19 18 17 16 15
RB3/AN9/CPS3/CCP2(1) RB2/AN8/CPS2 RB1/AN10/CPS1 RB0/AN12/CPS0/INT VDD VSS RC7/RX/DT
T1CKI/T1OSO/RC0 CCP2(1)/T1OSI/RC1 2010 Microchip Technology Inc.
Note 1: CCP2 pin location may be selected as RB3 or RC1. 2: SS pin location may be selected as RA5 or RA0. 3: PIC16F722A/723A devices only.
SCL/SCK/RC3 SDA/SDI/RC4 SDO/RC5 CK/TX/RC6
CCP1/RC2
DS41417A-page 5
PIC16F/LF722A/723A
TABLE 1:
I/O 28-Pin PDIP, SOIC, SSOP 2 3 4 5 6 7 10 9 21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 1 20 8,19 1: 2: 3: 4:
28-PIN PDIP/SOIC/SSOP/QFN/UQFN SUMMARY (PIC16F/LF722A/723A)
28-Pin QFN, UQFN 27 28 1 2 3 4 7 6 18 19 20 21 22 23 24 25 8 9 10 11 12 13 14 15 26 17 5,16 A/D Cap Sensor Timers CCP AUSART SSP Interrupt Pull-Up Basic
RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 RC0 RC1 RC2 RC3 RC4 RC5 RC6 RC7 RE3 -- -- Note
AN0 AN1 AN2 AN3/VREF -- AN4 -- -- AN12 AN10 AN8 AN9 AN11 AN13 -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- CPS6 CPS7 -- -- CPS0 CPS1 CPS2 CPS3 CPS4 CPS5 -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- T0CKI -- -- -- -- -- -- -- -- T1G -- -- T1OSO/T1CKI T1OSI -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- CCP2(2) -- -- -- -- -- CCP2(2) CCP1 -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TX/CK RX/DT -- -- --
SS(3) -- -- -- -- SS(3) -- -- -- -- -- -- -- -- -- -- -- -- -- SCK/SCL SDI/SDA SDO -- -- -- -- --
-- -- -- -- -- -- -- -- IOC/INT IOC IOC IOC IOC IOC IOC IOC -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- Y Y Y Y Y Y Y Y -- -- -- -- -- -- -- -- Y(1) -- --
VCAP(4) -- -- -- -- VCAP(4) OSC2/CLKOUT/VCAP(4) OSC1/CLKIN -- -- -- -- -- -- ICSPCLK/ICDCLK ICSPDAT/ICDDAT -- -- -- -- -- -- -- -- MCLR/VPP VDD VSS
Pull-up enabled only with external MCLR configuration. RC1 is the default pin location for CCP2. RB3 may be selected by changing the CCP2SEL bit in the APFCON register. RA5 is the default pin location for SS. RA0 may be selected by changing the SSSEL bit in the APFCON register. PIC16F722A/723A devices only.
Note:
The PIC16F722A/723A devices have an internal low dropout voltage regulator. An external capacitor must be connected to one of the available VCAP pins to stabilize the regulator. For more information, see Section 5.0 "Low Dropout (LDO) Voltage Regulator". The PIC16LF722A/723A devices do not have the voltage regulator and therefore no external capacitor is required.
DS41417A-page 6
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
Table of Contents
1.0 Device Overview ......................................................................................................................................................................... 9 2.0 Memory Organization ................................................................................................................................................................ 15 3.0 Resets ....................................................................................................................................................................................... 27 4.0 Interrupts ................................................................................................................................................................................... 37 5.0 Low Dropout (LDO) Voltage Regulator ..................................................................................................................................... 45 6.0 I/O Ports .................................................................................................................................................................................... 47 7.0 Oscillator Module....................................................................................................................................................................... 77 8.0 Device Configuration .................................................................................................................................................................. 83 9.0 Analog-to-Digital Converter (ADC) Module ............................................................................................................................... 87 10.0 Fixed Voltage Reference........................................................................................................................................................... 97 11.0 Timer0 Module .......................................................................................................................................................................... 99 12.0 Timer1 Module with Gate Control............................................................................................................................................ 103 13.0 Timer2 Module ........................................................................................................................................................................ 115 14.0 Capacitive Sensing Module..................................................................................................................................................... 117 15.0 Capture/Compare/PWM (CCP) Module .................................................................................................................................. 123 16.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART) .......................................................... 133 17.0 SSP Module Overview ............................................................................................................................................................ 155 18.0 Program Memory Read ........................................................................................................................................................... 177 19.0 Power-Down Mode (Sleep) ..................................................................................................................................................... 181 20.0 In-Circuit Serial ProgrammingTM (ICSPTM) .............................................................................................................................. 183 21.0 Instruction Set Summary ......................................................................................................................................................... 185 22.0 Development Support.............................................................................................................................................................. 195 23.0 Electrical Specifications........................................................................................................................................................... 199 24.0 DC and AC Characteristics Graphs and Charts ...................................................................................................................... 227 25.0 Packaging Information............................................................................................................................................................. 263 Appendix A: Data Sheet Revision History......................................................................................................................................... 273 Appendix B: Migrating From Other PIC(R) Devices............................................................................................................................. 273 The Microchip Web Site .................................................................................................................................................................... 281 Customer Change Notification Service ............................................................................................................................................. 281 Customer Support ............................................................................................................................................................................. 281 Reader Response ............................................................................................................................................................................. 282 Product Identification System ............................................................................................................................................................ 283
2010 Microchip Technology Inc.
DS41417A-page 7
PIC16F/LF722A/723A
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS41417A-page 8
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
1.0 DEVICE OVERVIEW
The PIC16F/LF722A/723A devices are covered by this data sheet. They are available in 28-pin packages. Figure 1-1 shows a block diagram of the PIC16F/LF722A/723A devices. Table 1-1 shows the pinout descriptions.
2010 Microchip Technology Inc.
DS41417A-page 9
PIC16F/LF722A/723A
FIGURE 1-1: PIC16F/LF722A/723A BLOCK DIAGRAM
Configuration 13 Program Counter Flash Program Memory Data Bus 8 PORTA RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 PORTB RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 RC0 RC1 RC2 RC3 RC4 RC5 RC6 RC7 RE3 W Reg W reg
8 Level Stack (13-bit)
RAM
Program Bus
14 Instruction Reg Instruction reg Direct Addr 7
RAM Addr
9
Addr MUX 8 Indirect Addr
FSR Reg FSR reg 8 3 STATUS Reg STATUS reg PORTC
Power-up Timer Instruction Decode and Decode & Control Timing Generation Oscillator Start-up Timer Power-on Reset Watchdog Timer Brown-out Reset LDO(1) Regulator 8
MUX
ALU PORTE
OSC1/CLKIN OSC2/CLKOUT
Internal Oscillator Block
CCP1 CCP1
MCLR VDD T1OSI T1OSO T0CKI
VSS
CCP2 CCP2
Timer1 32 kHz Oscillator TX/CK RX/DT T1G T1CKI
SDI/ SCK/ SDO SDA SCL
SS
VREF
Timer0
Timer1
Timer2
AUSART AUSART
Synchronous Serial Port
Analog-To-Digital Converter
Capacitive Sensing Module
AN0 AN1 AN2 AN3 AN4 AN8 AN9 AN10 AN11 AN12 AN13
CPS0 CPS1 CPS2 CPS3 CPS4 CPS5 CPS6 CPS7
Note
1:
PIC16F722A/723A only.
DS41417A-page 10
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 1-1: PIC16F722A/723A PINOUT DESCRIPTION
Function RA0 AN0 SS VCAP RA1/AN1 RA2/AN2 RA3/AN3/VREF RA1 AN1 RA2 AN2 RA3 AN3 VREF RA4/CPS6/T0CKI RA4 CPS6 T0CKI RA5/AN4/CPS7/SS/VCAP RA5 AN4 CPS7 SS VCAP RA6/OSC2/CLKOUT/VCAP RA6 OSC2 CLKOUT VCAP RA7/OSC1/CLKIN RA7 OSC1 CLKIN CLKIN RB0/AN12/CPS0/INT RB0 AN12 CPS0 INT RB1/AN10/CPS1 RB1 AN10 CPS1 RB2/AN8/CPS2 RB2 AN8 CPS2 RB3/AN9/CPS3/CCP2 RB3 AN9 CPS3 CCP2 Input Type TTL AN ST Power TTL AN TTL AN TTL AN AN TTL AN ST TTL AN AN ST Power TTL -- -- Power TTL XTAL CMOS ST TTL AN AN ST TTL AN AN TTL AN AN TTL AN AN ST Output Type CMOS General purpose I/O. -- -- Power -- -- -- -- -- -- -- -- -- Power XTAL Power -- -- -- A/D Channel 0 input. Slave Select input. Filter capacitor for Voltage Regulator (PIC16F722A/723A only). A/D Channel 1 input. A/D Channel 2 input. A/D Channel 3 input. A/D Voltage Reference input. Capacitive sensing input 6. Timer0 clock input. A/D Channel 4 input. Capacitive sensing input 7. Slave Select input. Filter capacitor for Voltage Regulator (PIC16F722A/723A only). Crystal/Resonator (LP, XT, HS modes). Filter capacitor for Voltage Regulator (PIC16F722A/723A only). Crystal/Resonator (LP, XT, HS modes). External clock input (EC mode). RC oscillator connection (RC mode). Description
Name RA0/AN0/SS/VCAP
CMOS General purpose I/O. CMOS General purpose I/O. CMOS General purpose I/O.
CMOS General purpose I/O.
CMOS General purpose I/O.
CMOS General purpose I/O. CMOS FOSC/4 output. CMOS General purpose I/O.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- -- A/D Channel 12 input. Capacitive sensing input 0. External interrupt.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- A/D Channel 10 input. Capacitive sensing input 1.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- A/D Channel 8 input. Capacitive sensing input 2.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- A/D Channel 9 input. Capacitive sensing input 3.
CMOS Capture/Compare/PWM2.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2CTM= Schmitt Trigger input with I2C HV = High Voltage XTAL = Crystal levels
2010 Microchip Technology Inc.
DS41417A-page 11
PIC16F/LF722A/723A
TABLE 1-1: PIC16F722A/723A PINOUT DESCRIPTION (CONTINUED)
Function RB4 AN11 CPS4 RB5/AN13/CPS5/T1G RB5 AN13 CPS5 T1G RB6/ICSPCLK/ICDCLK RB6 ICSPCLK ICDCLK RB7/ICSPDAT/ICDDAT RB7 ICSPDAT ICDDAT RC0/T1OSO/T1CKI RC0 T1OSO T1CKI RC1/T1OSI/CCP2 RC1 T1OSI CCP2 RC2/CCP1 RC3/SCK/SCL RC2 CCP1 RC3 SCK SCL RC4/SDI/SDA RC4 SDI SDA RC5/SDO RC6/TX/CK RC5 SDO RC6 TX CK RC7/RX/DT RC7 RX DT RE3/MCLR/VPP RE3 MCLR VPP VDD VSS VDD VSS Input Type TTL AN AN TTL AN AN ST TTL ST ST TTL ST ST ST XTAL ST ST XTAL ST ST ST ST ST I2CTM ST ST I2CTM ST -- ST -- ST ST ST ST TTL ST HV Power Power Output Type Description Name RB4/AN11/CPS4
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- A/D Channel 11 input. Capacitive sensing input 4.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- -- A/D Channel 13 input. Capacitive sensing input 5. Timer1 gate input.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. -- -- Serial Programming Clock. In-Circuit Debug Clock.
CMOS General purpose I/O. Individually controlled interrupt-on-change. Individually enabled pull-up. CMOS ICSPTM Data I/O. -- XTAL -- XTAL In-Circuit Data I/O. Timer1 oscillator connection. Timer1 clock input. Timer1 oscillator connection. CMOS General purpose I/O.
CMOS General purpose I/O. CMOS Capture/Compare/PWM2. CMOS General purpose I/O. CMOS Capture/Compare/PWM1. CMOS General purpose I/O. CMOS SPI clock. OD -- OD I2CTM clock. SPI data input. I2CTM data input/output. CMOS General purpose I/O.
CMOS General purpose I/O. CMOS SPI data output. CMOS General purpose I/O. CMOS USART asynchronous transmit. CMOS USART synchronous clock. CMOS General purpose I/O. -- -- -- -- -- -- USART asynchronous input. General purpose input. Master Clear with internal pull-up. Programming voltage. Positive supply. Ground reference. CMOS USART synchronous data.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2CTM= Schmitt Trigger input with I2C HV = High Voltage XTAL = Crystal levels
DS41417A-page 12
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
Note: The PIC16F722A/723A devices have an internal low dropout voltage regulator. An external capacitor must be connected to one of the available VCAP pins to stabilize the regulator. For more information, see Section 5.0 "Low Dropout (LDO) Voltage Regulator". The PIC16LF722A/723A devices do not have the voltage regulator and therefore no external capacitor is required.
2010 Microchip Technology Inc.
DS41417A-page 13
PIC16F/LF722A/723A
NOTES:
DS41417A-page 14
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
2.0
2.1
MEMORY ORGANIZATION
Program Memory Organization
FIGURE 2-2:
PROGRAM MEMORY MAP AND STACK FOR THE PIC16F/LF723A
PC<12:0>
The PIC16F/LF722A/723A has a 13-bit program counter capable of addressing a 2K x 14 program memory space for the PIC16F/LF722A (0000h-07FFh) and a 4K x 14 program memory space for the PIC16F/LF723A (0000h-0FFFh). Accessing a location above the memory boundaries for the PIC16F/LF722A will cause a wrap-around within the first 2K x 14 program memory space. Accessing a location above the memory boundaries for the PIC16F/LF723A will cause a wrap-around within the first 4K x 14 program memory space. The Reset vector is at 0000h and the interrupt vector is at 0004h.
CALL, RETURN RETFIE, RETLW
13
Stack Level 1 Stack Level 2 Stack Level 8 RESET Vector Interrupt Vector On-chip Program Memory Page 0 Page 1 07FFh 0800h 0FFFh 1000h Wraps to Page 0 17FFh 1800h Wraps to Page 1 1FFFh 0000h 0004H 0005h
FIGURE 2-1:
PROGRAM MEMORY MAP AND STACK FOR THE PIC16F/LF722A
PC<12:0>
CALL, RETURN RETFIE, RETLW
13
Stack Level 1 Stack Level 2 Stack Level 8 RESET Vector Interrupt Vector On-chip Program Memory Page 0 07FFh 0800h Wraps to Page 0 0FFFh 1000h Wraps to Page 0 17FFh 1800h Wraps to Page 0 1FFFh 0000h 0004H 0005h
2010 Microchip Technology Inc.
DS41417A-page 15
PIC16F/LF722A/723A
2.2 Data Memory Organization
2.2.1
The data memory is partitioned into multiple banks which contain the General Purpose Registers (GPRs) and the Special Function Registers (SFRs). Bits RP0 and RP1 are bank select bits. RP1 0 0 1 1 RP0 0 1 0 1 Bank 0 is selected Bank 1 is selected Bank 2 is selected Bank 3 is selected
GENERAL PURPOSE REGISTER FILE
The register file is organized as 128 x 8 bits in the PIC16F/LF722A and 192 x 8 bits in the PIC16F/LF723A. Each register is accessed either directly or indirectly through the File Select Register (FSR), (Refer to Section 2.5 "Indirect Addressing, INDF and FSR Registers").
2.2.2
SPECIAL FUNCTION REGISTERS
Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are the General Purpose Registers, implemented as static RAM. All implemented banks contain Special Function Registers. Some frequently used Special Function Registers from one bank are mirrored in another bank for code reduction and quicker access.
The Special Function Registers are registers used by the CPU and peripheral functions for controlling the desired operation of the device (refer to Table 2-1). These registers are static RAM. The Special Function Registers can be classified into two sets: core and peripheral. The Special Function Registers associated with the "core" are described in this section. Those related to the operation of the peripheral features are described in the section of that peripheral feature.
DS41417A-page 16
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 2-3:
Indirect addr.(*) TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTE PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES ADCON0
PIC16F/LF722A SPECIAL FUNCTION REGISTERS
File Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h General Purpose Register 32 Bytes ADCON1 APFCON FVRCON TXSTA SPBRG TRISE PCLATH INTCON PIE1 PIE2 PCON T1GCON OSCCON OSCTUNE PR2 SSPSTAT WPUB IOCB Indirect addr.(*) OPTION PCL STATUS FSR TRISA TRISB TRISC 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h CPSCON0 CPSCON1 PCLATH INTCON PMDATL PMADRL PMDATH PMADRH Indirect addr.(*) TMR0 PCL STATUS FSR 100h 101h 102h 103h 104h 105h 106h 107h 108h 109h 10Ah 10Bh 10Ch 10Dh 10Eh 10Fh 110h 111h 112h 113h 114h 115h 116h 117h 118h 119h 11Ah 11Bh 11Ch 11Dh 11Eh 11Fh 120h PCLATH INTCON PMCON1 Reserved Reserved Reserved Indirect addr.(*) OPTION PCL STATUS FSR ANSELA ANSELB 180h 181h 182h 183h 184h 185h 186h 187h 188h 189h 18Ah 18Bh 18Ch 18Dh 18Eh 18Fh 190h 191h 192h 193h 194h 195h 196h 197h 198h 199h 19Ah 19Bh 19Ch 19Dh 19Eh 19Fh 1A0h
SSPADD/SSPMSK 93h
General Purpose Register 96 Bytes Accesses 70h-7Fh 7Fh Bank 0 Legend: Bank 1
BFh C0h EFh F0h Accesses 70h-7Fh FFh Bank 2 17Fh Bank 3 16Fh 170h Accesses 70h-7Fh 1FFh 1EFh 1F0h
= Unimplemented data memory locations, read as `0'. * = Not a physical register.
2010 Microchip Technology Inc.
DS41417A-page 17
PIC16F/LF722A/723A
FIGURE 2-4:
Indirect addr.(*) TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTE PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES ADCON0
PIC16F/LF723A SPECIAL FUNCTION REGISTERS
File Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h General Purpose Register 80 Bytes EFh Accesses 70h-7Fh 7Fh F0h FFh Bank 1 Bank 2 Accesses 70h-7Fh ADCON1 APFCON FVRCON TXSTA SPBRG TRISE PCLATH INTCON PIE1 PIE2 PCON T1GCON OSCCON OSCTUNE PR2 SSPSTAT WPUB IOCB Indirect addr.(*) OPTION PCL STATUS FSR TRISA TRISB TRISC 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h CPSCON0 CPSCON1 PCLATH INTCON PMDATL PMADRL PMDATH PMADRH Indirect addr.(*) TMR0 PCL STATUS FSR 100h 101h 102h 103h 104h 105h 106h 107h 108h 109h 10Ah 10Bh 10Ch 10Dh 10Eh 10Fh 110h 111h 112h 113h 114h 115h 116h 117h 118h 119h 11Ah 11Bh 11Ch 11Dh 11Eh 11Fh General Purpose 120h Register 16 Bytes 12Fh 130h PCLATH INTCON PMCON1 Reserved Reserved Reserved Indirect addr.(*) OPTION PCL STATUS FSR ANSELA ANSELB 180h 181h 182h 183h 184h 185h 186h 187h 188h 189h 18Ah 18Bh 18Ch 18Dh 18Eh 18Fh 190h 191h 192h 193h 194h 195h 196h 197h 198h 199h 19Ah 19Bh 19Ch 19Dh 19Eh 19Fh 1A0h
SSPADD/SSPMSK 93h
General Purpose Register 96 Bytes
16Fh 170h 17Fh Bank 3 Accesses 70h-7Fh
1EFh 1F0h 1FFh
Bank 0 Legend:
= Unimplemented data memory locations, read as `0'. * = Not a physical register.
DS41417A-page 18
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 2-1:
Address Bank 0 00h(2) 01h 02h(2) 03h(2) 04h(2) 05h 06h 07h 09h 0Ah(1, 2) 0Bh(2) 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh Legend: Note 1: 2: 3: 4: 5: INDF TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTE PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES ADCON0 Addressing this location uses contents of FSR to address data memory (not a physical register) Timer0 Module Register Program Counter (PC) Least Significant Byte IRP RA7 RB7 RC7 -- -- GIE TMR1GIF -- RP1 RA6 RB6 RC6 -- -- PEIE ADIF -- RP0 RA5 RB5 RC5 -- -- T0IE RCIF -- TO RA4 RB4 RC4 -- INTE TXIF -- PD RA3 RB3 RC3 RE3 RBIE SSPIF -- Z RA2 RB2 RC2 -- T0IF CCP1IF -- DC RA1 RB1 RC1 -- INTF TMR2IF -- C RA0 RB0 RC0 -- RBIF TMR1IF CCP2IF Indirect Data Memory Address Pointer xxxx xxxx xxxx xxxx 0000 0000 0001 1xxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx ---- xxxx ---0 0000 0000 000x 0000 0000 ---- ---0 xxxx xxxx xxxx xxxx -- TMR1ON 0000 00-0 0000 0000 TOUTPS1 CKP TOUTPS0 SSPM3 TMR2ON SSPM2 T2CKPS1 T2CKPS0 SSPM1 SSPM0 -000 0000 xxxx xxxx 0000 0000 xxxx xxxx xxxx xxxx CCP1M3 ADDEN CCP1M2 FERR CCP1M1 OERR CCP1M0 RX9D --00 0000 0000 000x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx CCP2M3 CHS1 CCP2M2 CHS0 CCP2M1 GO/DONE CCP2M0 ADON --00 0000 xxxx xxxx CHS3 CHS2 --00 0000 26,34 99,34 25,34 22,34 26,34 48,34 57,34 67,34 74,34 25,34 40,34 43,34 44,34 108,34 108,34 112,34 115,34 116,34 157,34 174,34 125,34 125,34 124,34 143,34 142,34 140,34 125,34 125,34 124,34 93,34 92,34 Name
PIC16F/LF722A/723A SPECIAL FUNCTION REGISTER SUMMARY
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Page
Write Buffer for the upper 5 bits of the Program Counter
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register Holding Register for the Most Significant Byte of the 16-bit TMR1 Register TMR1CS1 TMR1CS0 T1CKPS1 Timer2 Module Register -- WCOL TOUTPS3 TOUTPS2 SSPOV SSPEN Synchronous Serial Port Receive Buffer/Transmit Register Capture/Compare/PWM Register (LSB) Capture/Compare/PWM Register (MSB) -- SPEN -- RX9 DC1B1 SREN DC1B0 CREN T1CKPS0 T1OSCEN T1SYNC
USART Transmit Data Register USART Receive Data Register Capture/Compare/PWM Register 2 (LSB) Capture/Compare/PWM Register 2 (MSB) -- -- -- -- DC2B1 DC2B0 A/D Result Register
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as `0', r = reserved. Shaded locations are unimplemented, read as `0'. The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8>, whose contents are transferred to the upper byte of the program counter. These registers can be addressed from any bank. Accessible only when SSPM<3:0> = 1001. Accessible only when SSPM<3:0> 1001. This bit is always `1' as RE3 is input only.
2010 Microchip Technology Inc.
DS41417A-page 19
PIC16F/LF722A/723A
TABLE 2-1:
Address Bank 1 80h(2) 81h 82h(2) 83h(2) 84h(2) 85h 86h 87h 89h 8Ah(1, 2) 8Bh(2) 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh Legend: Note 1: 2: 3: 4: 5: INDF OPTION_REG PCL STATUS FSR TRISA TRISB TRISC TRISE PCLATH INTCON PIE1 PIE2 PCON T1GCON OSCCON OSCTUNE PR2 SSPADD(4) SSPMSK(3) SSPSTAT WPUB IOCB -- TXSTA SPBRG -- -- APFCON FVRCON -- ADCON1 Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU IRP TRISA7 TRISB7 TRISC7 -- -- GIE TMR1GIE -- -- TMR1GE -- -- INTEDG RP1 TRISA6 TRISB6 TRISC6 -- -- PEIE ADIE -- -- T1GPOL -- -- T0CS RP0 TRISA5 TRISB5 TRISC5 -- -- T0IE RCIE -- -- T1GTM IRCF1 TUN5 T0SE TO TRISA4 TRISB4 TRISC4 -- INTE TXIE -- -- T1GSPM IRCF0 TUN4 PSA PD TRISA3 TRISB3 TRISC3 TRISE3(5) RBIE SSPIE -- -- T1GGO/ DONE ICSL TUN3 PS2 Z TRISA2 TRISB2 TRISC2 -- T0IF CCP1IE -- -- T1GVAL ICSS TUN2 PS1 DC TRISA1 TRISB1 TRISC1 -- INTF TMR2IE -- POR T1GSS1 -- TUN1 PS0 C TRISA0 TRISB0 TRISC0 -- RBIF TMR1IE CCP2IE BOR T1GSS0 -- TUN0 Program Counter (PC) Least Significant Byte Indirect Data Memory Address Pointer xxxx xxxx 1111 1111 0000 0000 0001 1xxx xxxx xxxx 1111 1111 1111 1111 1111 1111 ---- 1111 ---0 0000 0000 000x 0000 0000 ---- ---0 ---- --qq 0000 0x00 --10 qq---00 0000 1111 1111 0000 0000 1111 1111 R/W WPUB2 IOCB2 BRGH BRG2 UA WPUB1 IOCB1 TRMT BRG1 BF WPUB0 IOCB0 TX9D BRG0 0000 0000 1111 1111 0000 0000 -- TX9 BRG6 TXEN BRG5 SYNC BRG4 -- BRG3 0000 -010 0000 0000 -- -- -- FVREN ADCS2 -- -- ADCS1 -- -- ADCS0 -- -- -- -- -- -- SSSEL ADFVR1 ADREF1 CCP2SEL ---- --00 ADFVR0 ADREF0 q0-- --00 -- 0000 --00 26,34 23,35 25,34 22,34 26,34 48,35 57,35 67,35 74,35 25,34 40,34 41,35 42,35 24,35 113,35 79,35 80,35 115,35 165,35 176,35 163,35 57,35 58,35 -- 142,35 144,35 -- -- 47,35 97,35 -- 93,35 Name
PIC16F/LF722A/723A SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Page
Write Buffer for the upper 5 bits of the Program Counter
Timer2 Period Register Synchronous Serial Port (I2CTM mode) Address Register Synchronous Serial Port (I2CTM mode) Address Mask Register SMP WPUB7 IOCB7 CSRC BRG7 Unimplemented Unimplemented -- FVRRDY -- Unimplemented CKE WPUB6 IOCB6 D/A WPUB5 IOCB5 P WPUB4 IOCB4 S WPUB3 IOCB3
Unimplemented
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as `0', r = reserved. Shaded locations are unimplemented, read as `0'. The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8>, whose contents are transferred to the upper byte of the program counter. These registers can be addressed from any bank. Accessible only when SSPM<3:0> = 1001. Accessible only when SSPM<3:0> 1001. This bit is always `1' as RE3 is input only.
DS41417A-page 20
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 2-1:
Address Bank 2 100h(2) 101h 102h(2) 103h(2) 104h(2) 105h 106h 107h 108h 109h 10Bh(2) 10Ch 10Dh 10Eh 10Fh Bank 3 180h(2) 181h 182h(2) 183h(2) 184h(2) 185h 186h 187h 18Bh(2) 18Ch 18Dh 18Eh 18Fh Legend: Note 1: 2: 3: 4: 5: INDF OPTION_REG PCL STATUS FSR ANSELA ANSELB -- INTCON PMCON1 -- -- -- Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU IRP -- -- Unimplemented -- GIE Reserved Unimplemented Unimplemented Unimplemented -- PEIE -- -- T0IE -- Write Buffer for the upper 5 bits of the Program Counter INTE -- RBIE -- T0IF -- INTF -- RBIF RD INTEDG RP1 -- -- T0CS RP0 ANSA5 ANSB5 T0SE TO ANSA4 ANSB4 PSA PD ANSA3 ANSB3 PS2 Z ANSA2 ANSB2 PS1 DC ANSA1 ANSB1 PS0 C ANSA0 ANSB0 Program Counter (PC) Least Significant Byte Indirect Data Memory Address Pointer xxxx xxxx 1111 1111 0000 0000 0001 1xxx xxxx xxxx --11 1111 --11 1111 -- ---0 0000 0000 000x 1--- ---0 -- -- -- 26,34 23,35 25,34 22,34 26,34 49,35 58,35 -- 25,34 40,34 178,35 -- -- -- INDF TMR0 PCL STATUS FSR -- -- -- CPSCON0 CPSCON1 INTCON PMDATL PMADRL PMDATH PMADRH Addressing this location uses contents of FSR to address data memory (not a physical register) Timer0 Module Register Program Counter's (PC) Least Significant Byte IRP RP1 RP0 TO PD Z DC C Indirect Data Memory Address Pointer Unimplemented Unimplemented Unimplemented CPSON -- -- GIE -- -- -- PEIE -- -- -- T0IE -- -- INTE CPSRNG1 CPSRNG0 CPSCH3 RBIE CPSCH2 T0IF CPSOUT CPSCH1 INTF T0XCS CPSCH0 RBIF xxxx xxxx xxxx xxxx 0000 0000 0001 1xxx xxxx xxxx -- -- -- 0--- 0000 ---- 0000 ---0 0000 0000 000x xxxx xxxx xxxx xxxx --xx xxxx ---x xxxx 26,34 99,34 25,34 22,34 26,34 -- -- -- 121,35 122,35 25,34 40,34 177,35 177,35 177,35 177,35 Name
PIC16F/LF722A/723A SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Page
10Ah(1, 2) PCLATH
Write Buffer for the upper 5 bits of the Program Counter
Program Memory Read Data Register Low Byte Program Memory Read Address Register Low Byte -- -- -- -- Program Memory Read Data Register High Byte -- Program Memory Read Address Register High Byte
18Ah(1, 2) PCLATH
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as `0', r = reserved. Shaded locations are unimplemented, read as `0'. The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8>, whose contents are transferred to the upper byte of the program counter. These registers can be addressed from any bank. Accessible only when SSPM<3:0> = 1001. Accessible only when SSPM<3:0> 1001. This bit is always `1' as RE3 is input only.
2010 Microchip Technology Inc.
DS41417A-page 21
PIC16F/LF722A/723A
2.2.2.1 STATUS Register
The STATUS register, shown in Register 2-1, contains: * the arithmetic status of the ALU * the Reset status * the bank select bits for data memory (SRAM) The STATUS register can be the destination for any instruction, like any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will clear the upper three bits and set the Z bit. This leaves the STATUS register as `000u u1uu' (where u = unchanged). It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect any Status bits. For other instructions not affecting any Status bits (Refer to Section 21.0 "Instruction Set Summary"). Note 1: The C and DC bits operate as Borrow and Digit Borrow out bits, respectively, in subtraction.
REGISTER 2-1:
R/W-0 IRP bit 7 Legend: R = Readable bit -n = Value at POR bit 7
STATUS: STATUS REGISTER
R/W-0 RP1 R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC(1) R/W-x C(1) bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
IRP: Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h-1FFh) 0 = Bank 0, 1 (00h-FFh) RP<1:0>: Register Bank Select bits (used for direct addressing) 00 = Bank 0 (00h-7Fh) 01 = Bank 1 (80h-FFh) 10 = Bank 2 (100h-17Fh) 11 = Bank 3 (180h-1FFh) TO: Time-out bit 1 = After power-up, CLRWDT instruction or SLEEP instruction 0 = A WDT time-out occurred PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero DC: Digit Carry/Digit Borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)(1) 1 = A carry-out from the 4th low-order bit of the result occurred 0 = No carry-out from the 4th low-order bit of the result C: Carry/Borrow bit(1) (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1) 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred For Borrow, the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order bit of the source register.
bit 6-5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
DS41417A-page 22
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
2.2.2.2 OPTION register
Note: To achieve a 1:1 prescaler assignment for Timer0, assign the prescaler to the WDT by setting PSA bit of the OPTION register to `1'. Refer to Section 12.3 "Timer1 Prescaler". The OPTION register, shown in Register 2-2, is a readable and writable register, which contains various control bits to configure: * * * * Timer0/WDT prescaler External RB0/INT interrupt Timer0 Weak pull-ups on PORTB
REGISTER 2-2:
R/W-1 RBPU bit 7 Legend: R = Readable bit -n = Value at POR bit 7
OPTION_REG: OPTION REGISTER
R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual bits in the WPUB register INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin T0CS: Timer0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (FOSC/4) T0SE: Timer0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module PS<2:0>: Prescaler Rate Select bits
Bit Value Timer0 Rate WDT Rate
bit 6
bit 5
bit 4
bit 3
bit 2-0
000 001 010 011 100 101 110 111
1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256
1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128
2010 Microchip Technology Inc.
DS41417A-page 23
PIC16F/LF722A/723A
2.2.2.3 PCON Register
The Power Control (PCON) register contains flag bits (refer to Table 3-2) to differentiate between a: * * * * Power-on Reset (POR) Brown-out Reset (BOR) Watchdog Timer Reset (WDT) External MCLR Reset
The PCON register also controls the software enable of the BOR. The PCON register bits are shown in Register 2-3.
REGISTER 2-3:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR
PCON: POWER CONTROL REGISTER
U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-q POR R/W-q BOR bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
q = Value depends on condition bit 7-2 bit 1 Unimplemented: Read as `0' POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Power-on Reset or Brown-out Reset occurs) Set BOREN<1:0> = 01 in the Configuration Word register for this bit to control the BOR.
bit 0
Note 1:
DS41417A-page 24
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
2.3 PCL and PCLATH
Note 1: There are no Status bits to indicate stack overflow or stack underflow conditions. 2: There are no instructions/mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL, RETURN, RETLW and RETFIE instructions or the vectoring to an interrupt address. The Program Counter (PC) is 13 bits wide. The low byte comes from the PCL register, which is a readable and writable register. The high byte (PC<12:8>) is not directly readable or writable and comes from PCLATH. On any Reset, the PC is cleared. Figure 2-5 shows the two situations for the loading of the PC. The upper example in Figure 2-5 shows how the PC is loaded on a write to PCL (PCLATH<4:0> PCH). The lower example in Figure 2-5 shows how the PC is loaded during a CALL or GOTO instruction (PCLATH<4:3> PCH).
2.4
Program Memory Paging
FIGURE 2-5:
PCH 12 PC 5 87
LOADING OF PC IN DIFFERENT SITUATIONS
PCL 0 8 Instruction with PCL as Destination ALU Result
PCLATH<4:0> PCLATH
PCH 12 11 10 8 7 PC 2 PCLATH<4:3> PCLATH
PCL 0 GOTO, CALL 11 Opcode<10:0>
All devices are capable of addressing a continuous 8K word block of program memory. The CALL and GOTO instructions provide only 11 bits of address to allow branching within any 2K program memory page. When doing a CALL or GOTO instruction, the upper 2 bits of the address are provided by PCLATH<4:3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bits are programmed so that the desired program memory page is addressed. If a return from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is POPed off the stack. Therefore, manipulation of the PCLATH<4:3> bits is not required for the RETURN instructions (which POPs the address from the stack). Note: The contents of the PCLATH register are unchanged after a RETURN or RETFIE instruction is executed. The user must rewrite the contents of the PCLATH register for any subsequent subroutine calls or GOTO instructions.
2.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset to the program counter (ADDWF PCL). When performing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary (each 256-byte block). Refer to Application Note AN556, "Implementing a Table Read" (DS00556).
Example 2-1 shows the calling of a subroutine in page 1 of the program memory. This example assumes that PCLATH is saved and restored by the Interrupt Service Routine (if interrupts are used).
EXAMPLE 2-1:
CALL OF A SUBROUTINE IN PAGE 1 FROM PAGE 0
2.3.2
STACK
All devices have an 8-level x 13-bit wide hardware stack (refer to Figures 2-1 and 2-2). The stack space is not part of either program or data space and the Stack Pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not affected by a PUSH or POP operation. The stack operates as a circular buffer. This means that after the stack has been PUSHed eight times, the ninth PUSH overwrites the value that was stored from the first PUSH. The tenth PUSH overwrites the second PUSH (and so on).
ORG 500h PAGESEL SUB_P1 ;Select page 1 ;(800h-FFFh) CALL SUB1_P1 ;Call subroutine in : ;page 1 (800h-FFFh) : ORG 900h ;page 1 (800h-FFFh) SUB1_P1 : : RETURN ;called subroutine ;page 1 (800h-FFFh) ;return to ;Call subroutine ;in page 0 ;(000h-7FFh)
2010 Microchip Technology Inc.
DS41417A-page 25
PIC16F/LF722A/723A
2.5 Indirect Addressing, INDF and FSR Registers
EXAMPLE 2-2: INDIRECT ADDRESSING
MOVLW020h ;initialize pointer MOVWFFSR ;to RAM BANKISEL020h NEXTCLRFINDF ;clear INDF register INCFFSR ;inc pointer BTFSSFSR,4 ;all done? GOTONEXT ;no clear next CONTINUE ;yes continue
The INDF register is not a physical register. Addressing the INDF register will cause indirect addressing. Indirect addressing is possible by using the INDF register. Any instruction using the INDF register actually accesses data pointed to by the File Select Register (FSR). Reading INDF itself indirectly will produce 00h. Writing to the INDF register indirectly results in a no operation (although Status bits may be affected). An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit of the STATUS register, as shown in Figure 2-6. A simple program to clear RAM location 020h-02Fh using indirect addressing is shown in Example 2-2.
FIGURE 2-6:
DIRECT/INDIRECT ADDRESSING
Indirect Addressing 0 IRP 7 File Select Register0
Direct Addressing RP1 RP0 6 From Opcode
Bank Select
Location Select 00h 00 01 10 11
Bank Select 180h
Location Select
Data Memory
7Fh Bank 0 Note: Bank 1 Bank 2 Bank 3 For memory map detail, refer to Figures 2-3 and 2-4.
1FFh
DS41417A-page 26
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
3.0 RESETS
between The PIC16F/LF722A/723A differentiates various kinds of Reset: a) b) c) d) e) f) Power-on Reset (POR) WDT Reset during normal operation WDT Reset during Sleep MCLR Reset during normal operation MCLR Reset during Sleep Brown-out Reset (BOR) Most registers are not affected by a WDT wake-up since this is viewed as the resumption of normal operation. TO and PD bits are set or cleared differently in different Reset situations, as indicated in Table 3-3. These bits are used in software to determine the nature of the Reset. A simplified block diagram of the On-Chip Reset Circuit is shown in Figure 3-1. The MCLR Reset path has a noise filter to detect and ignore small pulses. See Section 23.0 "Electrical Specifications" for pulse width specifications.
Some registers are not affected in any Reset condition; their status is unknown on POR and unchanged in any other Reset. Most other registers are reset to a "Reset state" on: * * * * * Power-on Reset (POR) MCLR Reset MCLR Reset during Sleep WDT Reset Brown-out Reset (BOR)
FIGURE 3-1:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
MCLRE
MCLR/VPP WDT Module
Sleep WDT Time-out Reset
POR VDD Power-on Reset Brown-out(1) Reset BOREN OST/PWRT OST 10-bit Ripple Counter OSC1/ CLKIN PWRT WDTOSC 11-bit Ripple Counter Chip_Reset
Enable PWRT Enable OST
Note
1:
Refer to the Configuration Word Register 1 (Register 8-1).
2010 Microchip Technology Inc.
DS41417A-page 27
PIC16F/LF722A/723A
TABLE 3-1:
POR 0 0 0 1 1 1 1 1 BOR x x x 0 1 1 1 1
STATUS BITS AND THEIR SIGNIFICANCE
TO 1 0 x 1 0 0 u 1 PD 1 x 0 1 1 0 u 0 Power-on Reset or LDO Reset Illegal, TO is set on POR Illegal, PD is set on POR Brown-out Reset WDT Reset WDT Wake-up MCLR Reset during normal operation MCLR Reset during Sleep or interrupt wake-up from Sleep Condition
TABLE 3-2:
RESET CONDITION FOR SPECIAL REGISTERS(2)
Condition Program Counter 0000h 0000h 0000h 0000h PC + 1 0000h PC + 1
(1)
STATUS Register 0001 1xxx 000u uuuu 0001 0uuu 0000 1uuu uuu0 0uuu 0001 1uuu uuu1 0uuu
PCON Register ---- --0x ---- --uu ---- --uu ---- --uu ---- --uu ---- --u0 ---- --uu
Power-on Reset MCLR Reset during normal operation MCLR Reset during Sleep WDT Reset WDT Wake-up Brown-out Reset Interrupt Wake-up from Sleep
Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0'. Note 1: When the wake-up is due to an interrupt and Global Enable bit (GIE) is set, the return address is pushed on the stack and PC is loaded with the interrupt vector (0004h) after execution of PC + 1. 2: If a Status bit is not implemented, that bit will be read as `0'.
DS41417A-page 28
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
3.1 MCLR 3.3 Power-up Timer (PWRT)
The PIC16F/LF722A/723A has a noise filter in the MCLR Reset path. The filter will detect and ignore small pulses. It should be noted that a Reset does not drive the MCLR pin low. Voltages applied to the pin that exceed its specification can result in both MCLR Resets and excessive current beyond the device specification during the ESD event. For this reason, Microchip recommends that the MCLR pin no longer be tied directly to VDD. The use of an RC network, as shown in Figure 3-2, is suggested. An internal MCLR option is enabled by clearing the MCLRE bit in the Configuration Word register. When MCLRE = 0, the Reset signal to the chip is generated internally. When the MCLRE = 1, the RE3/MCLR pin becomes an external Reset input. In this mode, the RE3/MCLR pin has a weak pull-up to VDD. In-Circuit Serial Programming is not affected by selecting the internal MCLR option. The Power-up Timer provides a fixed 64 ms (nominal) time-out on power-up only, from POR or Brown-out Reset. The Power-up Timer operates from the WDT oscillator. For more information, see Section 7.3 "Internal Clock Modes". The chip is kept in Reset as long as PWRT is active. The PWRT delay allows the VDD to rise to an acceptable level. A Configuration bit, PWRTE, can disable (if set) or enable (if cleared or programmed) the Power-up Timer. The Power-up Timer should be enabled when Brown-out Reset is enabled, although it is not required. The Power-up Timer delay will vary from chip-to-chip and vary due to: * VDD variation * Temperature variation * Process variation See DC parameters for details "Electrical Specifications"). Note: (Section 23.0
FIGURE 3-2:
VDD R1 10 k
RECOMMENDED MCLR CIRCUIT
PIC MCU
(R)
The Power-up Timer is enabled by the PWRTE bit in the Configuration Word.
3.4
Watchdog Timer (WDT)
The WDT has the following features: * Shares an 8-bit prescaler with Timer0 * Time-out period is from 17 ms to 2.2 seconds, nominal * Enabled by a Configuration bit WDT is cleared under certain conditions described in Table 3-1.
MCLR C1 0.1 F
3.4.1
WDT OSCILLATOR
3.2
Power-on Reset (POR)
The WDT derives its time base from 31 kHz internal oscillator. Note: When the Oscillator Start-up Timer (OST) is invoked, the WDT is held in Reset, because the WDT Ripple Counter is used by the OST to perform the oscillator delay count. When the OST count has expired, the WDT will begin counting (if enabled).
The on-chip POR circuit holds the chip in Reset until VDD has reached a high enough level for proper operation. A maximum rise time for VDD is required. See Section 23.0 "Electrical Specifications" for details. If the BOR is enabled, the maximum rise time specification does not apply. The BOR circuitry will keep the device in Reset until VDD reaches VBOR (see Section 3.5 "Brown-Out Reset (BOR)"). When the device starts normal operation (exits the Reset condition), device operating parameters (i.e., voltage, frequency, temperature, etc.) must be met to ensure operation. If these conditions are not met, the device must be held in Reset until the operating conditions are met. For additional information, refer to Application Note AN607, "Power-up Trouble Shooting" (DS00607).
2010 Microchip Technology Inc.
DS41417A-page 29
PIC16F/LF722A/723A
3.4.2 WDT CONTROL
The WDTE bit is located in the Configuration Word Register 1. When set, the WDT runs continuously. The PSA and PS<2:0> bits of the OPTION register control the WDT period. See Section 11.0 "Timer0 Module" for more information.
FIGURE 3-1:
T1GSS = 11 TMR1GE
WATCHDOG TIMER BLOCK DIAGRAM
WDTE Low-Power WDT OSC
From TMR0 Clock Source
0 Divide by 512 Postscaler 1 8
PS<2:0> TO TMR0 PSA 0 1 WDT Reset To T1G WDTE
TABLE 3-1:
WDTE = 0
WDT STATUS
Conditions WDT Cleared
CLRWDT Command Exit Sleep + System Clock = T1OSC, EXTRC, INTOSC, EXTCLK Exit Sleep + System Clock = XT, HS, LP Cleared until the end of OST
DS41417A-page 30
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
3.5 Brown-Out Reset (BOR)
Brown-out Reset is enabled by programming the BOREN<1:0> bits in the Configuration register. The brown-out trip point is selectable from two trip points via the BORV bit in the Configuration register. Between the POR and BOR, complete voltage range coverage for execution protection can be implemented. Two bits are used to enable the BOR. When BOREN = 11, the BOR is always enabled. When BOREN = 10, the BOR is enabled, but disabled during Sleep. When BOREN = 0X, the BOR is disabled. If VDD falls below VBOR for greater than parameter (TBOR) (see Section 23.0 "Electrical Specifications"), the brown-out situation will reset the device. This will occur regardless of VDD slew rate. A Reset is not ensured to occur if VDD falls below VBOR for more than parameter (TBOR). If VDD drops below VBOR while the Power-up Timer is running, the chip will go back into a Brown-out Reset and the Power-up Timer will be re-initialized. Once VDD rises above VBOR, the Power-up Timer will execute a 64 ms Reset. Note: When erasing Flash program memory, the BOR is forced to enabled at the minimum BOR setting to ensure that any code protection circuitry is operating properly.
FIGURE 3-3:
VDD
BROWN-OUT SITUATIONS
VBOR
Internal Reset VDD
64 ms(1)
VBOR < 64 ms
Internal Reset
64 ms(1)
VDD
VBOR
Internal Reset Note 1: 64 ms delay only if PWRTE bit is programmed to `0'.
64 ms(1)
2010 Microchip Technology Inc.
DS41417A-page 31
PIC16F/LF722A/723A
3.6 Time-out Sequence 3.7 Power Control (PCON) Register
On power-up, the time-out sequence is as follows: first, PWRT time-out is invoked after POR has expired, then OST is activated after the PWRT time-out has expired. The total time-out will vary based on oscillator configuration and PWRTE bit status. For example, in EC mode with PWRTE bit = 1 (PWRT disabled), there will be no time-out at all. Figure 3-4, Figure 3-5 and Figure 3-6 depict time-out sequences. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then, bringing MCLR high will begin execution immediately (see Figure 3-5). This is useful for testing purposes or to synchronize more than one PIC16F/LF722A/723A device operating in parallel. Table 3-3 shows the Reset conditions for some special registers. The Power Control (PCON) register has two Status bits to indicate what type of Reset that last occurred. Bit 0 is BOR (Brown-out Reset). BOR is unknown on Power-on Reset. It must then be set by the user and checked on subsequent Resets to see if BOR = 0, indicating that a brown-out has occurred. The BOR Status bit is a "don't care" and is not necessarily predictable if the brown-out circuit is disabled (BOREN<1:0> = 00 in the Configuration Word register). Bit 1 is POR (Power-on Reset). It is a `0' on Power-on Reset and unaffected otherwise. The user must write a `1' to this bit following a Power-on Reset. On a subsequent Reset, if POR is `0', it will indicate that a Power-on Reset has occurred (i.e., VDD may have gone too low). For more information, see Section 3.5 "Brown-Out Reset (BOR)".
TABLE 3-2:
TIME-OUT IN VARIOUS SITUATIONS
Power-up PWRTE = 0 TPWRT + 1024 * TOSC TPWRT PWRTE = 1 1024 * TOSC -- Brown-out Reset PWRTE = 0 TPWRT + 1024 * TOSC TPWRT PWRTE = 1 1024 * TOSC -- Wake-up from Sleep 1024 * TOSC --
Oscillator Configuration XT, HS, LP(1)
RC, EC, INTOSC Note 1:
LP mode with T1OSC disabled.
TABLE 3-3:
POR 0 1 u u u u u 0 u u u u
RESET BITS AND THEIR SIGNIFICANCE
BOR TO 1 1 0 0 u 1 PD 1 1 u 0 u 0 Power-on Reset Brown-out Reset WDT Reset WDT Wake-up MCLR Reset during normal operation MCLR Reset during Sleep Condition
Legend: u = unchanged, x = unknown
DS41417A-page 32
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 3-4: TIME-OUT SEQUENCE ON POWER-UP (DELAYED MCLR): CASE 1
VDD MCLR Internal POR TPWRT PWRT Time-out OST Time-out Internal Reset TOST
FIGURE 3-5:
TIME-OUT SEQUENCE ON POWER-UP (DELAYED MCLR): CASE 2
VDD MCLR Internal POR TPWRT PWRT Time-out OST Time-out Internal Reset TOST
FIGURE 3-6:
TIME-OUT SEQUENCE ON POWER-UP (MCLR WITH VDD): CASE 3
VDD MCLR Internal POR TPWRT PWRT Time-out OST Time-out Internal Reset TOST
2010 Microchip Technology Inc.
DS41417A-page 33
PIC16F/LF722A/723A
TABLE 3-4:
Register W INDF TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTE PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES ADCON0 Legend: Note 1: 2: 3: 4: 5:
INITIALIZATION CONDITION FOR REGISTERS
Address -- 00h/80h/ 100h/180h 01h/101h 02h/82h/ 102h/182h 03h/83h/ 103h/183h 04h/84h/ 104h/184h 05h 06h 07h 09h 0Ah/8Ah/ 10Ah/18Ah 0Bh/8Bh/ 10Bh/18Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh Power-on Reset/ Brown-out Reset(1) xxxx xxxx xxxx xxxx xxxx xxxx 0000 0000 0001 1xxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx ---- x-----0 0000 0000 000x 0000 0000 ---- ---0 xxxx xxxx xxxx xxxx 0000 00-0 0000 0000 -000 0000 xxxx xxxx 0000 0000 xxxx xxxx xxxx xxxx --00 0000 0000 000x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx --00 0000 xxxx xxxx --00 0000 MCLR Reset/ WDT Reset uuuu uuuu xxxx xxxx uuuu uuuu 0000 0000 000q quuu(4) uuuu uuuu xxxx xxxx xxxx xxxx xxxx xxxx ---- x-----0 0000 0000 000x 0000 0000 ---- ---0 uuuu uuuu uuuu uuuu uuuu uu-u 0000 0000 -000 0000 xxxx xxxx 0000 0000 xxxx xxxx xxxx xxxx --00 0000 0000 000x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx --00 0000 uuuu uuuu --00 0000 Wake-up from Sleep through Interrupt/Time-out uuuu uuuu uuuu uuuu uuuu uuuu PC + 1(3) uuuq quuu(4) uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---- u-----u uuuu uuuu uuuu(2) uuuu uuuu(2) ---- ---u uuuu uuuu uuuu uuuu uuuu uu-u uuuu uuuu -uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu --uu uuuu
u = unchanged, x = unknown, - = unimplemented bit, reads as `0', q = value depends on condition. If VDD goes too low, Power-on Reset will be activated and registers will be affected differently. One or more bits in INTCON and/or PIR1 and PIR2 will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). See Table 3-5 for Reset value for specific condition. If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
DS41417A-page 34
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 3-4:
Register OPTION_REG TRISA TRISB TRISC TRISE PIE1 PIE2 PCON T1GCON OSCCON OSCTUNE PR2 SSPADD SSPMSK SSPSTAT WPUB IOCB TXSTA SPBRG APFCON FVRCON ADCON1 CPSCON0 CPSCON1 PMDATL PMADRL PMDATH PMADRH ANSELA ANSELB PMCON1 Legend: Note 1: 2: 3: 4: 5:
INITIALIZATION CONDITION FOR REGISTERS (CONTINUED)
Address 81h/181h 85h 86h 87h 89h 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 93h 94h 95h 96h 98h 99h 9Ch 9Dh 9Fh 108h 109h 10Ch 10Dh 10Eh 10Fh 185h 186h 18Ch Power-on Reset/ Brown-out Reset(1) 1111 1111 1111 1111 1111 1111 1111 1111 ---- 1--0000 0000 ---- ---0 ---- --qq 0000 0x00 --10 qq---00 0000 1111 1111 0000 0000 1111 1111 0000 0000 1111 1111 0000 0000 0000 -010 0000 0000 ---- --00 q000 --00 -000 --00 0--- 0000 ---- 0000 xxxx xxxx xxxx xxxx --xx xxxx ---x xxxx --11 1111 --11 1111 1--- ---0 MCLR Reset/ WDT Reset 1111 1111 1111 1111 1111 1111 1111 1111 ---- 1--0000 0000 ---- ---0 ---- --uu uuuu uxuu --10 qq---uu uuuu 1111 1111 0000 0000 1111 1111 0000 0000 1111 1111 0000 0000 0000 -010 0000 0000 ---- --00 q000 --00 -000 --00 0--- 0000 ---- 0000 xxxx xxxx xxxx xxxx --xx xxxx ---x xxxx --11 1111 --11 1111 1--- ---0
(1,5)
Wake-up from Sleep through Interrupt/Time-out uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---- u--uuuu uuuu ---- ---u ---- --uu uuuu uxuu --uu qq---uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu uuuu uuuu ---- --uu uuuu --uu -uuu --uu u--- uuuu ---- uuuu uuuu uuuu uuuu uuuu --uu uuuu ---u uuuu --uu uuuu --uu uuuu u--- ---u
u = unchanged, x = unknown, - = unimplemented bit, reads as `0', q = value depends on condition. If VDD goes too low, Power-on Reset will be activated and registers will be affected differently. One or more bits in INTCON and/or PIR1 and PIR2 will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). See Table 3-5 for Reset value for specific condition. If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
2010 Microchip Technology Inc.
DS41417A-page 35
PIC16F/LF722A/723A
TABLE 3-5: INITIALIZATION CONDITION FOR SPECIAL REGISTERS
Condition Power-on Reset MCLR Reset during normal operation MCLR Reset during Sleep WDT Reset WDT Wake-up Brown-out Reset Interrupt Wake-up from Sleep
-
Program Counter 0000h 0000h 0000h 0000h PC + 1 0000h PC + 1
(1)
STATUS Register 0001 1xxx 000u uuuu 0001 0uuu 0000 uuuu uuu0 0uuu 0001 1xxx uuu1 0uuu
PCON Register ---- --0x ---- --uu ---- --uu ---- --uu ---- --uu ---- --10 ---- --uu
Legend: u = unchanged, x = unknown, = unimplemented bit, reads as `0'. Note 1: When the wake-up is due to an interrupt and Global Interrupt Enable bit, GIE, is set, the PC is loaded with the interrupt vector (0004h) after execution of PC + 1.
TABLE 3-6:
Name STATUS PCON
SUMMARY OF REGISTERS ASSOCIATED WITH RESETS
Bit 7 IRP -- Bit 6 RP1 -- Bit 5 RP0 -- Bit 4 TO -- Bit 3 PD -- Bit 2 Z -- Bit 1 DC POR Bit 0 C BOR Value on POR, BOR 0001 1xxx ---- --qq Value on all other Resets(1) 000q quuu ---- --uu
Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0', q = value depends on condition. Shaded cells are not used by Resets. Note 1: Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
DS41417A-page 36
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
4.0 INTERRUPTS
The PIC16F/LF722A/723A device family features an interruptible core, allowing certain events to preempt normal program flow. An Interrupt Service Routine (ISR) is used to determine the source of the interrupt and act accordingly. Some interrupts can be configured to wake the MCU from Sleep mode. The PIC16F/LF722A/723A device family has 12 interrupt sources, differentiated by corresponding interrupt enable and flag bits: * * * * * * * * * * * * Timer0 Overflow Interrupt External Edge Detect on INT Pin Interrupt PORTB Change Interrupt Timer1 Gate Interrupt A/D Conversion Complete Interrupt AUSART Receive Interrupt AUSART Transmit Interrupt SSP Event Interrupt CCP1 Event Interrupt Timer2 Match with PR2 Interrupt Timer1 Overflow Interrupt CCP2 Event Interrupt
A block diagram of the interrupt logic is shown in Figure 4-1.
FIGURE 4-1:
IOC-RB0 IOCB0 IOC-RB1 IOCB1 IOC-RB2 IOCB2 IOC-RB3 IOCB3 IOC-RB4 IOCB4 IOC-RB5 IOCB5 IOC-RB6 IOCB6 IOC-RB7 IOCB7
INTERRUPT LOGIC
SSPIF SSPIE TXIF TXIE RCIF RCIE TMR2IF TMR2IE TMR1IF TMR1IE ADIF ADIE TMR1GIF TMR1GIE CCP1IF CCP1IE CCP2IF CCP2IE T0IF T0IE INTF INTE RBIF RBIE PEIE GIE Wake-up (If in Sleep mode)(1) Interrupt to CPU
Note 1:
Some peripherals depend upon the system clock for operation. Since the system clock is suspended during Sleep, these peripherals will not wake the part from Sleep. See Section 19.1 "Wake-up from Sleep".
2010 Microchip Technology Inc.
DS41417A-page 37
PIC16F/LF722A/723A
4.1 Operation
Interrupts are disabled upon any device Reset. They are enabled by setting the following bits: * GIE bit of the INTCON register * Interrupt Enable bit(s) for the specific interrupt event(s) * PEIE bit of the INTCON register (if the Interrupt Enable bit of the interrupt event is contained in the PIE1 and PIE2 registers) The INTCON, PIR1 and PIR2 registers record individual interrupts via interrupt flag bits. Interrupt flag bits will be set, regardless of the status of the GIE, PEIE and individual interrupt enable bits. The following events happen when an interrupt event occurs while the GIE bit is set: * Current prefetched instruction is flushed * GIE bit is cleared * Current Program Counter (PC) is pushed onto the stack * PC is loaded with the interrupt vector 0004h The ISR determines the source of the interrupt by polling the interrupt flag bits. The interrupt flag bits must be cleared before exiting the ISR to avoid repeated interrupts. Because the GIE bit is cleared, any interrupt that occurs while executing the ISR will be recorded through its interrupt flag, but will not cause the processor to redirect to the interrupt vector. The RETFIE instruction exits the ISR by popping the previous address from the stack and setting the GIE bit. For additional information on a specific interrupt's operation, refer to its peripheral chapter. Note 1: Individual interrupt flag bits are set, regardless of the state of any other enable bits. 2: All interrupts will be ignored while the GIE bit is cleared. Any interrupt occurring while the GIE bit is clear will be serviced when the GIE bit is set again.
4.2
Interrupt Latency
Interrupt latency is defined as the time from when the interrupt event occurs to the time code execution at the interrupt vector begins. The latency for synchronous interrupts is 3 instruction cycles. For asynchronous interrupts, the latency is 3 to 4 instruction cycles, depending on when the interrupt occurs. See Figure 4-2 for timing details.
FIGURE 4-2:
Q1 OSC1 CLKOUT (3) INT pin INTF flag (INTCON<1>) GIE bit (INTCON<7>) INSTRUCTION FLOW PC Instruction Fetched Instruction Executed Note 1: 2: 3: 4: 5:
INT PIN INTERRUPT TIMING
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
(4) (1) (1) (5)
Interrupt Latency (2)
PC
PC + 1 Inst (PC + 1) Inst (PC)
PC + 1 -- Dummy Cycle
0004h Inst (0004h) Dummy Cycle
0005h Inst (0005h) Inst (0004h)
Inst (PC) Inst (PC - 1)
INTF flag is sampled here (every Q1). Asynchronous interrupt latency = 3-4 TCY. Synchronous latency = 3 TCY, where TCY = instruction cycle time. Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction. CLKOUT is available only in INTOSC and RC Oscillator modes. For minimum width of INT pulse, refer to AC specifications in Section 23.0 "Electrical Specifications". INTF is enabled to be set any time during the Q4-Q1 cycles.
DS41417A-page 38
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
4.3 Interrupts During Sleep
Some interrupts can be used to wake from Sleep. To wake from Sleep, the peripheral must be able to operate without the system clock. The interrupt source must have the appropriate interrupt enable bit(s) set prior to entering Sleep. On waking from Sleep, if the GIE bit is also set, the processor will branch to the interrupt vector. Otherwise, the processor will continue executing instructions after the SLEEP instruction. The instruction directly after the SLEEP instruction will always be executed before branching to the ISR. Refer to Section 19.0 "PowerDown Mode (Sleep)" for more details. following the ISR from using invalid data. Examples of key registers include the W, STATUS, FSR and PCLATH registers. Note: The microcontroller does not normally require saving the PCLATH register. However, if computed GOTO's are used, the PCLATH register must be saved at the beginning of the ISR and restored when the ISR is complete to ensure correct program flow.
The code shown in Example 4-1 can be used to do the following. * * * * * * * Save the W register Save the STATUS register Save the PCLATH register Execute the ISR program Restore the PCLATH register Restore the STATUS register Restore the W register
4.4
INT Pin
The external interrupt, INT pin, causes an asynchronous, edge-triggered interrupt. The INTEDG bit of the OPTION register determines on which edge the interrupt will occur. When the INTEDG bit is set, the rising edge will cause the interrupt. When the INTEDG bit is clear, the falling edge will cause the interrupt. The INTF bit of the INTCON register will be set when a valid edge appears on the INT pin. If the GIE and INTE bits are also set, the processor will redirect program execution to the interrupt vector. This interrupt is disabled by clearing the INTE bit of the INTCON register.
4.5
Context Saving
Since most instructions modify the W register, it must be saved immediately upon entering the ISR. The SWAPF instruction is used when saving and restoring the W and STATUS registers because it will not affect any bits in the STATUS register. It is useful to place W_TEMP in shared memory because the ISR cannot predict which bank will be selected when the interrupt occurs. The processor will branch to the interrupt vector by loading the PC with 0004h. The PCLATH register will remain unchanged. This requires the ISR to ensure that the PCLATH register is set properly before using an instruction that causes PCLATH to be loaded into the PC. See Section 2.3 "PCL and PCLATH" for details on PC operation.
When an interrupt occurs, only the return PC value is saved to the stack. If the ISR modifies or uses an instruction that modifies key registers, their values must be saved at the beginning of the ISR and restored when the ISR completes. This prevents instructions
EXAMPLE 4-1:
MOVWFW_TEMP SWAPFSTATUS,W
SAVING W, STATUS AND PCLATH REGISTERS IN RAM
;Copy W to W_TEMP register ;Swap status to be saved into W ;Swaps are used because they do not affect the status bits ;Select regardless of current bank ;Copy status to bank zero STATUS_TEMP register ;Copy PCLATH to W register ;Copy W register to PCLATH_TEMP ;Insert user code here ;Select regardless of current bank ; ;Restore PCLATH ;Swap STATUS_TEMP register into W ;(sets bank to original state) ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W
BANKSELSTATUS_TEMP MOVWFSTATUS_TEMP MOVF PCLATH,W MOVWF PCLATH_TEMP : :(ISR) : BANKSELSTATUS_TEMP MOVF PCLATH_TEMP,W MOVWF PCLATH SWAPFSTATUS_TEMP,W MOVWFSTATUS SWAPFW_TEMP,F SWAPFW_TEMP,W
2010 Microchip Technology Inc.
DS41417A-page 39
PIC16F/LF722A/723A
4.5.1 INTCON REGISTER
Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE of the INTCON register. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. The INTCON register is a readable and writable register, which contains the various enable and flag bits for TMR0 register overflow, PORTB change and external RB0/INT/SEG0 pin interrupts.
REGISTER 4-1:
R/W-0 GIE bit 7 Legend: R = Readable bit -n = Value at POR bit 7
INTCON: INTERRUPT CONTROL REGISTER
R/W-0 PEIE R/W-0 T0IE R/W-0 INTE R/W-0 RBIE(1) R/W-0 T0IF(2) R/W-0 INTF R/W-x RBIF bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
GIE: Global Interrupt Enable bit 1 = Enables all unmasked interrupts 0 = Disables all interrupts PEIE: Peripheral Interrupt Enable bit 1 = Enables all unmasked peripheral interrupts 0 = Disables all peripheral interrupts T0IE: Timer0 Overflow Interrupt Enable bit 1 = Enables the Timer0 interrupt 0 = Disables the Timer0 interrupt INTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt RBIE: PORTB Change Interrupt Enable bit(1) 1 = Enables the PORTB change interrupt 0 = Disables the PORTB change interrupt T0IF: Timer0 Overflow Interrupt Flag bit(2) 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur RBIF: PORTB Change Interrupt Flag bit 1 = When at least one of the PORTB general purpose I/O pins changed state (must be cleared in software) 0 = None of the PORTB general purpose I/O pins have changed state The appropriate bits in the IOCB register must also be set. T0IF bit is set when Timer0 rolls over. Timer0 is unchanged on Reset and should be initialized before clearing T0IF bit.
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1: 2:
DS41417A-page 40
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
4.5.2 PIE1 REGISTER
Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt. The PIE1 register contains the interrupt enable bits, as shown in Register 4-2.
REGISTER 4-2:
R/W-0 TMR1GIE bit 7 Legend: R = Readable bit -n = Value at POR bit 7
PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
R/W-0 ADIE R/W-0 RCIE R/W-0 TXIE R/W-0 SSPIE R/W-0 CCP1IE R/W-0 TMR2IE R/W-0 TMR1IE bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TMR1GIE: Timer1 Gate Interrupt Enable bit 1 = Enable the Timer1 gate acquisition complete interrupt 0 = Disable the Timer1 gate acquisition complete interrupt ADIE: A/D Converter (ADC) Interrupt Enable bit 1 = Enables the ADC interrupt 0 = Disables the ADC interrupt RCIE: USART Receive Interrupt Enable bit 1 = Enables the USART receive interrupt 0 = Disables the USART receive interrupt TXIE: USART Transmit Interrupt Enable bit 1 = Enables the USART transmit interrupt 0 = Disables the USART transmit interrupt SSPIE: Synchronous Serial Port (SSP) Interrupt Enable bit 1 = Enables the SSP interrupt 0 = Disables the SSP interrupt CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the Timer2 to PR2 match interrupt 0 = Disables the Timer2 to PR2 match interrupt TMR1IE: Timer1 Overflow Interrupt Enable bit 1 = Enables the Timer1 overflow interrupt 0 = Disables the Timer1 overflow interrupt
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2010 Microchip Technology Inc.
DS41417A-page 41
PIC16F/LF722A/723A
4.5.3 PIE2 REGISTER
Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt. The PIE2 register contains the interrupt enable bits, as shown in Register 4-3.
REGISTER 4-3:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-1 bit 0
PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2
U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 CCP2IE bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' CCP2IE: CCP2 Interrupt Enable bit 1 = Enables the CCP2 interrupt 0 = Disables the CCP2 interrupt
DS41417A-page 42
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
4.5.4 PIR1 REGISTER
The PIR1 register contains the interrupt flag bits, as shown in Register 4-4. Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE of the INTCON register. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 4-4:
R/W-0 TMR1GIF bit 7 Legend: R = Readable bit -n = Value at POR bit 7
PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1
R/W-0 ADIF R-0 RCIF R-0 TXIF R/W-0 SSPIF R/W-0 CCP1IF R/W-0 TMR2IF R/W-0 TMR1IF bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TMR1GIF: Timer1 Gate Interrupt Flag bit 1 = Timer1 gate is inactive 0 = Timer1 gate is active ADIF: A/D Converter Interrupt Flag bit 1 = A/D conversion complete (must be cleared in software) 0 = A/D conversion has not completed or has not been started RCIF: USART Receive Interrupt Flag bit 1 = The USART receive buffer is full (cleared by reading RCREG) 0 = The USART receive buffer is not full TXIF: USART Transmit Interrupt Flag bit 1 = The USART transmit buffer is empty (cleared by writing to TXREG) 0 = The USART transmit buffer is full SSPIF: Synchronous Serial Port (SSP) Interrupt Flag bit 1 = The Transmission/Reception is complete (must be cleared in software) 0 = Waiting to Transmit/Receive CCP1IF: CCP1 Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode TMR2IF: Timer2 to PR2 Interrupt Flag bit 1 = A Timer2 to PR2 match occurred (must be cleared in software) 0 = No Timer2 to PR2 match occurred TMR1IF: Timer1 Overflow Interrupt Flag bit 1 = The TMR1 register overflowed (must be cleared in software) 0 = The TMR1 register did not overflow
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2010 Microchip Technology Inc.
DS41417A-page 43
PIC16F/LF722A/723A
4.5.5 PIR2 REGISTER
The PIR2 register contains the interrupt flag bits, as shown in Register 4-5. Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE of the INTCON register. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 4-5:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-1 bit 0
PIR2: PERIPHERAL INTERRUPT REQUEST REGISTER 2
U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 CCP2IF bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' CCP2IF: CCP2 Interrupt Flag bit Capture Mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode
TABLE 4-1:
Name INTCON OPTION_REG PIE1 PIE2 PIR1 PIR2
SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPTS
Bit 7 GIE RBPU TMR1GIE -- TMR1GIF -- Bit 6 PEIE INTEDG ADIE -- ADIF -- Bit 5 T0IE T0CS RCIE -- RCIF -- Bit 4 INTE T0SE TXIE -- TXIF -- Bit 3 RBIE PSA SSPIE -- SSPIF -- Bit 2 T0IF PS2 CCP1IE -- CCP1IF -- Bit 1 INTF PS1 TMR2IE -- TMR2IF -- Bit 0 RBIF PS0 Value on POR, BOR Value on all other Resets
0000 000x 0000 000x 1111 1111 1111 1111
TMR1IE 0000 0000 0000 0000 CCP2IE ---- ---0 ---- ---0 TMR1IF 0000 0000 0000 0000 CCP2IF ---- ---0 ---- ---0
Legend: - = Unimplemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the Capture, Compare and PWM.
DS41417A-page 44
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
5.0 LOW DROPOUT (LDO) VOLTAGE REGULATOR
The PIC16F722A/723A devices differ from the PIC16LF722A/723A devices due to an internal Low Dropout (LDO) voltage regulator. The PIC16F722A/ 723A contain an internal LDO, while the PIC16LF722A/ 723A do not. The lithography of the die allows a maximum operating voltage of 3.6V on the internal digital logic. In order to continue to support 5.0V designs, a LDO voltage regulator is integrated on the die. The LDO voltage regulator allows for the internal digital logic to operate at 3.2V, while I/O's operate at 5.0V (VDD). The LDO voltage regulator requires an external bypass capacitor for stability. One of three pins, denoted as VCAP, can be configured for the external bypass capacitor. It is recommended that the capacitor be a ceramic cap between 0.1 to 1.0 F. The VCAP pin is not intended to supply power to external loads. An external voltage regulator should be used if this functionality is required. In addition, external devices should not supply power to the VCAP pin. On power-up, the external capacitor will look like a large load on the LDO voltage regulator. To prevent erroneous operation, the device is held in Reset while a constant current source charges the external capacitor. After the cap is fully charged, the device is released from Reset. For more information, refer to Section 23.0 "Electrical Specifications". See Configuration Word 2 register (Register 8-2) for VCAP enable bits.
2010 Microchip Technology Inc.
DS41417A-page 45
PIC16F/LF722A/723A
NOTES:
DS41417A-page 46
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
6.0 I/O PORTS
There are as many as thirty-five general purpose I/O pins available. Depending on which peripherals are enabled, some or all of the pins may not be available as general purpose I/O. In general, when a peripheral is enabled, the associated pin may not be used as a general purpose I/O pin.
6.1
Alternate Pin Function
The Alternate Pin Function Control (APFCON) register is used to steer specific peripheral input and output functions between different pins. The APFCON register is shown in Register 6-1. For this device family, the following functions can be moved between different pins: * SS (Slave Select) * CCP2
REGISTER 6-1:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-2 bit 1
APFCON: ALTERNATE PIN FUNCTION CONTROL REGISTER
U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 SSSEL R/W-0 CCP2SEL bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0'. SSSEL: SS Input Pin Selection bit 0 = SS function is on RA5/AN4/CPS7/SS/VCAP 1 = SS function is on RA0/AN0/SS/VCAP CCP2SEL: CCP2 Input/Output Pin Selection bit 0 = CCP2 function is on RC1/T1OSI/CCP2 1 = CCP2 function is on RB3/CCP2
bit 0
2010 Microchip Technology Inc.
DS41417A-page 47
PIC16F/LF722A/723A
6.2 PORTA and the TRISA Registers
PORTA is a 8-bit wide, bidirectional port. The corresponding data direction register is TRISA (Register 6-3). Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., disable the output driver). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., enables output driver and puts the contents of the output latch on the selected pin). Example 6-1 shows how to initialize PORTA. Reading the PORTA register (Register 6-2) reads the status of the pins, whereas writing to it will write to the PORT latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified and then written to the PORT data latch. The TRISA register (Register 6-3) controls the PORTA pin output drivers, even when they are being used as analog inputs. The user should ensure the bits in the TRISA register are maintained set when using them as analog inputs. I/O pins configured as analog input always read `0'. Note: The ANSELA register must be initialized to configure an analog channel as a digital input. Pins configured as analog inputs will read `0'.
EXAMPLE 6-1:
BANKSEL CLRF BANKSEL CLRF BANKSEL MOVLW MOVWF PORTA PORTA ANSELA ANSELA TRISA 0Ch TRISA
INITIALIZING PORTA
; ;Init PORTA ; ;digital I/O ; ;Set RA<3:2> as inputs ;and set RA<7:4,1:0> ;as outputs
REGISTER 6-2:
R/W-x RA7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
PORTA: PORTA REGISTER
R/W-x RA6 R/W-x RA5 R/W-x RA4 R/W-x RA3 R/W-x RA2 R/W-x RA1 R/W-x RA0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
RA<7:0>: PORTA I/O Pin bit 1 = Port pin is > VIH 0 = Port pin is < VIL
REGISTER 6-3:
R/W-1 TRISA7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
TRISA: PORTA TRI-STATE REGISTER
R/W-1 TRISA6 R/W-1 TRISA5 R/W-1 TRISA4 R/W-1 TRISA3 R/W-1 TRISA2 R/W-1 TRISA1 R/W-1 TRISA0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TRISA<7:0>: PORTA Tri-State Control bit 1 = PORTA pin configured as an input (tri-stated) 0 = PORTA pin configured as an output
DS41417A-page 48
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
6.2.1 ANSELA REGISTER
The ANSELA register (Register 6-4) is used to configure the Input mode of an I/O pin to analog. Setting the appropriate ANSELA bit high will cause all digital reads on the pin to be read as `0' and allow analog functions on the pin to operate correctly. The state of the ANSELA bits has no affect on digital output functions. A pin with TRIS clear and ANSEL set will still operate as a digital output, but the Input mode will be analog. This can cause unexpected behavior when executing read-modify-write instructions on the affected port.
REGISTER 6-4:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-0
ANSELA: PORTA ANALOG SELECT REGISTER
U-0 -- R/W-1 ANSA5 R/W-1 ANSA4 R/W-1 ANSA3 R/W-1 ANSA2 R/W-1 ANSA1 R/W-1 ANSA0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' ANSA<5:0>: Analog Select between Analog or Digital Function on pins RA<5:0>, respectively 0 = Digital I/O. Pin is assigned to port or digital special function. 1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled. When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to allow external control of the voltage on the pin.
Note 1:
2010 Microchip Technology Inc.
DS41417A-page 49
PIC16F/LF722A/723A
6.2.2 PIN DESCRIPTIONS AND DIAGRAMS 6.2.2.6 RA5/AN4/CPS7/SS/VCAP
Each PORTA pin is multiplexed with other functions. The pins and their combined functions are briefly described here. For specific information about individual functions such as the A/D Converter (ADC), refer to the appropriate section in this data sheet. Figure 6-4 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * * General purpose I/O Analog input for the ADC Capacitive sensing input Slave select input for the SSP(1) Voltage regulator capacitor pin (PIC16F722A/ 723A only) Note 1: SS pin location may be selected as RA5 or RA0.
6.2.2.1
RA0/AN0/SS/VCAP
Figure 6-1 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * General purpose I/O Analog input for the ADC Slave select input for the SSP(1) Voltage regulator capacitor pin (PIC16F722A/ 723A only) Note 1: SS pin location may be selected as RA5 or RA0.
6.2.2.7
RA6/OSC2/CLKOUT/VCAP
Figure 6-5 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * General purpose I/O Crystal/resonator connection Clock output Voltage regulator capacitor pin (PIC16F722A/ 723A only)
6.2.2.2
RA1/AN1
Figure 6-2 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC
6.2.2.8
RA7/OSC1/CLKIN
Figure 6-6 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Crystal/resonator connection * Clock input
6.2.2.3
RA2/AN2
Figure 6-2 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC
6.2.2.4
RA3/AN3/VREF
Figure 6-2 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC * Voltage reference input for the ADC
6.2.2.5
RA4/CPS6/T0CKI
Figure 6-3 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Capacitive sensing input * Clock input for Timer0 The Timer0 clock input function works independently of any TRIS register setting. Effectively, if TRISA4 = 0, the PORTA4 register bit will output to the pad and clock Timer0 at the same time.
DS41417A-page 50
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-1: BLOCK DIAGRAM OF RA0
PIC16F722A/723A only
To Voltage Regulator
VCAPEN = 00 VDD
Data Bus
D WR PORTA
Q I/O Pin
CK Q D Q VSS
WR TRISA RD TRISA ANSA0
CK Q
RD PORTA
TO SSP SS Input To A/D Converter
2010 Microchip Technology Inc.
DS41417A-page 51
PIC16F/LF722A/723A
FIGURE 6-2:
Data Bus
RA<3:1> BLOCK DIAGRAM
VDD
D WR PORTA
Q I/O Pin
CK Q D Q VSS
WR TRISA RD TRISA ANSAx
CK Q
RD PORTA To A/D Converter
FIGURE 6-3:
Data Bus
BLOCK DIAGRAM OF RA4
VDD
D WR PORTA
Q I/O Pin
CK Q D Q VSS
WR TRISA RD TRISA ANSA4
CK Q
RD PORTA
To Timer0 Clock MUX To Cap Sensor
DS41417A-page 52
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-4: BLOCK DIAGRAM OF RA5
PIC16F722A/723A only
VCAPEN = 01
To Voltage Regulator
Data Bus
VDD
D WR PORTA
Q I/O Pin
CK Q D Q VSS
WR TRISA RD TRISA ANSA5
CK Q
RD PORTA
To SSP SS Input To A/D Converter To Cap Sensor
2010 Microchip Technology Inc.
DS41417A-page 53
PIC16F/LF722A/723A
FIGURE 6-5: BLOCK DIAGRAM OF RA6
PIC16F722A/723A only
To Voltage Regulator
VCAPEN = 10
CLKOUT(1) Enable
Data Bus
Oscillator Circuit RA7/OSC1
VDD I/O Pin
FOSC/4 1
D WR PORTA Q
0
CK Q VSS D Q
WR TRISA RD TRISA FOSC = LP or XT or HS (00X OR 010)
CK Q
RD PORTA Note 1: CLKOUT Enable = 1 when FOSC = RC or INTOSC (No I/O Selected).
FIGURE 6-6:
BLOCK DIAGRAM OF RA7
Oscillator Circuit RA6/OSC2 D WR PORTA Q
Data Bus
VDD I/O Pin
CK Q D Q VSS
WR TRISA RD TRISA OSC = INTOSC or INTOSCIO
CK Q
RD PORTA
DS41417A-page 54
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 6-1:
Name ADCON0 ADCON1 ANSELA APFCON CPSCON0 CPSCON1 CONFIG2(1) OPTION_REG PORTA SSPCON TRISA Legend: Note 1:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Bit 7 -- -- -- -- CPSON -- -- RBPU RA7 WCOL TRISA7 Bit 6 -- ADCS2 -- -- -- -- -- INTEDG RA6 SSPOV TRISA6 Bit 5 CHS3 ADCS1 ANSA5 -- -- -- T0CS RA5 SSPEN TRISA5 Bit 4 CHS2 ADCS0 ANSA4 -- -- -- T0SE RA4 CKP TRISA4 Bit 3 CHS1 -- ANSA3 -- CPSCH3 -- PSA RA3 SSPM3 TRISA3 Bit 2 CHS0 -- ANSA2 -- CPSCH2 -- PS2 RA2 SSPM2 TRISA2 Bit 1 GO/DONE ADREF1 ANSA1 SSSEL CPSOUT CPSCH1 -- PS1 RA1 SSPM1 TRISA1 Bit 0 ADON ADREF0 ANSA0 CCP2SEL T0XCS CPSCH0 -- PS0 RA0 SSPM0 TRISA0 Value on POR, BOR 0000 0000 -000 --00 --11 1111 ---- --00 0--- 0000 ---- 0000 -- 1111 1111 xxxx xxxx 0000 0000 1111 1111 Value on all other Resets 0000 0000 -000 --00 --11 1111 ---- --00 0--- 0000 ---- 0000 -- 1111 1111 xxxx xxxx 0000 0000 1111 1111
CPSRNG1 CPSRNG0
VCAPEN1 VCAPEN0
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by PORTA. PIC16F722A/723A only.
2010 Microchip Technology Inc.
DS41417A-page 55
PIC16F/LF722A/723A
6.3 PORTB and TRISB Registers
6.3.1 ANSELB REGISTER
PORTB is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISB (Register 6-6). Setting a TRISB bit (= 1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a High-Impedance mode). Clearing a TRISB bit (= 0) will make the corresponding PORTB pin an output (i.e., enable the output driver and put the contents of the output latch on the selected pin). Example 6-2 shows how to initialize PORTB. Reading the PORTB register (Register 6-5) reads the status of the pins, whereas writing to it will write to the PORT latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified and then written to the PORT data latch. The TRISB register (Register 6-6) controls the PORTB pin output drivers, even when they are being used as analog inputs. The user should ensure the bits in the TRISB register are maintained set when using them as analog inputs. I/O pins configured as analog input always read `0'. Example 6-2 shows how to initialize PORTB. The ANSELB register (Register 6-9) is used to configure the Input mode of an I/O pin to analog. Setting the appropriate ANSELB bit high will cause all digital reads on the pin to be read as `0' and allow analog functions on the pin to operate correctly. The state of the ANSELB bits has no affect on digital output functions. A pin with TRIS clear and ANSELB set will still operate as a digital output, but the Input mode will be analog. This can cause unexpected behavior when executing read-modify-write instructions on the affected port.
6.3.2
WEAK PULL-UPS
Each of the PORTB pins has an individually configurable internal weak pull-up. Control bits WPUB<7:0> enable or disable each pull-up (see Register 6-7). Each weak pullup is automatically turned off when the port pin is configured as an output. All pull-ups are disabled on a Power-on Reset by the RBPU bit of the OPTION register.
6.3.3
INTERRUPT-ON-CHANGE
EXAMPLE 6-2:
BANKSEL CLRF BANKSEL CLRF BANKSEL MOVLW MOVWF
INITIALIZING PORTB
PORTB ; PORTB ;Init PORTB ANSELB ANSELB ;Make RB<7:0> digital TRISB ; B'11110000';Set RB<7:4> as inputs ;and RB<3:0> as outputs TRISB ;
All of the PORTB pins are individually configurable as an interrupt-on-change pin. Control bits IOCB<7:0> enable or disable the interrupt function for each pin. Refer to Register 6-8. The interrupt-on-change feature is disabled on a Power-on Reset. For enabled interrupt-on-change pins, the present value is compared with the old value latched on the last read of PORTB to determine which bits have changed or mismatched the old value. The `mismatch' outputs of the last read are OR'd together to set the PORTB Change Interrupt flag bit (RBIF) in the INTCON register. This interrupt can wake the device from Sleep. The user, in the Interrupt Service Routine, clears the interrupt by: a) b) Any read or write of PORTB. This will end the mismatch condition. Clear the flag bit RBIF.
Note:
The ANSELB register must be initialized to configure an analog channel as a digital input. Pins configured as analog inputs will read `0'.
A mismatch condition will continue to set flag bit RBIF. Reading or writing PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. The latch holding the last read value is not affected by a MCLR nor Brown-out Reset. After these Resets, the RBIF flag will continue to be set if a mismatch is present. Note: When a pin change occurs at the same time as a read operation on PORTB, the RBIF flag will always be set. If multiple PORTB pins are configured for the interrupt-on-change, the user may not be able to identify which pin changed state.
DS41417A-page 56
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 6-5:
R/W-x RB7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
PORTB: PORTB REGISTER
R/W-x RB6 R/W-x RB5 R/W-x RB4 R/W-x RB3 R/W-x RB2 R/W-x RB1 R/W-x RB0 bit 0
RB<7:0>: PORTB I/O Pin bits 1 = Port pin is > VIH 0 = Port pin is < VIL
REGISTER 6-6:
R/W-1 TRISB7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
TRISB: PORTB TRI-STATE REGISTER
R/W-1 TRISB6 R/W-1 TRISB5 R/W-1 TRISB4 R/W-1 TRISB3 R/W-1 TRISB2 R/W-1 TRISB1 R/W-1 TRISB0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TRISB<7:0>: PORTB Tri-State Control bits 1 = PORTB pin configured as an input (tri-stated) 0 = PORTB pin configured as an output
REGISTER 6-7:
R/W-1 WPUB7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
WPUB: WEAK PULL-UP PORTB REGISTER
R/W-1 WPUB6 R/W-1 WPUB5 R/W-1 WPUB4 R/W-1 WPUB3 R/W-1 WPUB2 R/W-1 WPUB1 R/W-1 WPUB0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
WPUB<7:0>: Weak Pull-up Register bits 1 = Pull-up enabled 0 = Pull-up disabled Global RBPU bit of the OPTION register must be cleared for individual pull-ups to be enabled. The weak pull-up device is automatically disabled if the pin is in configured as an output.
Note 1: 2:
2010 Microchip Technology Inc.
DS41417A-page 57
PIC16F/LF722A/723A
REGISTER 6-8:
R/W-0 IOCB7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
IOCB: INTERRUPT-ON-CHANGE PORTB REGISTER
R/W-0 IOCB6 R/W-0 IOCB5 R/W-0 IOCB4 R/W-0 IOCB3 R/W-0 IOCB2 R/W-0 IOCB1 R/W-0 IOCB0 bit 0
IOCB<7:0>: Interrupt-on-Change PORTB Control bits 1 = Interrupt-on-change enabled 0 = Interrupt-on-change disabled
REGISTER 6-9:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-0
ANSELB: PORTB ANALOG SELECT REGISTER
U-0 -- R/W-1 ANSB5 R/W-1 ANSB4 R/W-1 ANSB3 R/W-1 ANSB2 R/W-1 ANSB1 R/W-1 ANSB0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' ANSB<5:0>: Analog Select between Analog or Digital Function on Pins RB<5:0>, respectively 0 = Digital I/O. Pin is assigned to port or digital special function. 1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled. When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to allow external control of the voltage on the pin.
Note 1:
DS41417A-page 58
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
6.3.4 PIN DESCRIPTIONS AND DIAGRAMS 6.3.4.6 RB5/AN13/CPS5/T1G
Each PORTB pin is multiplexed with other functions. The pins and their combined functions are briefly described here. For specific information about individual functions such as the SSP, I2C or interrupts, refer to the appropriate section in this data sheet. Figure 6-10 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * General purpose I/O Analog input for the ADC Capacitive sensing input Timer1 gate input
6.3.4.1
RB0/AN12/CPS0/INT
Figure 6-7 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * General purpose I/O Analog input for the ADC Capacitive sensing input External edge triggered interrupt
6.3.4.7
RB6/ICSPCLK
Figure 6-11 shows the diagram for this pin. This pin is configurable to function as one of the following: * a general purpose I/O * In-Circuit Serial Programming clock
6.3.4.8
RB7/ICSPDAT
6.3.4.2
RB1/AN10/CPS1
Figure 6-8 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC * Capacitive sensing input
Figure 6-12 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * In-Circuit Serial Programming data
6.3.4.3
RB2/AN8/CPS2
Figure 6-8 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC * Capacitive sensing input
6.3.4.4
RB3/AN9/CPS3/CCP2
Figure 6-9 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * * General purpose I/O Analog input for the ADC Capacitive sensing input Capture 2 input, Compare 2 output, and PWM2 output Note: CCP2 pin location may be selected as RB3 or RC1.
6.3.4.5
RB4/AN11/CPS4
Figure 6-8 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Analog input for the ADC * Capacitive sensing input
2010 Microchip Technology Inc.
DS41417A-page 59
PIC16F/LF722A/723A
FIGURE 6-7:
Data Bus
BLOCK DIAGRAM OF RB0
D WR WPUB RD WPUB
D WR PORTB
Q
VDD Weak RBPU
VDD
CK Q
Q I/O Pin
CK Q
D WR TRISB RD TRISB ANSB0
Q
VSS
CK Q
RD PORTB
D
Q Q D EN
Q3
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB To External Interrupt Logic
To A/D Converter To Cap Sensor
DS41417A-page 60
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-8: BLOCK DIAGRAM OF RB4, RB<2:1>
Data Bus
D WR WPUB RD WPUB
D WR PORTB
Q
VDD Weak RBPU
VDD
CK Q
Q I/O Pin
CK Q
D WR TRISB RD TRISB ANSB<4,2,1>
Q
VSS
CK Q
RD PORTB
D
Q Q D EN
Q3 To A/D Converter To Cap Sensor
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB
2010 Microchip Technology Inc.
DS41417A-page 61
PIC16F/LF722A/723A
FIGURE 6-9: BLOCK DIAGRAM OF RB3
Data Bus
D WR WPUB RD WPUB
D WR PORTB
Q CCP2OUT Enable CCP2OUT 1
Q
VDD Weak
VDD
CK Q RBPU
0
I/O Pin
CK Q VSS
D WR TRISB RD TRISB ANSB<5,3>
Q
CK Q
RD PORTB
D
Q Q D EN
Q3
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB
To CCP2(1)
To A/D Converter To Cap Sensor
Note
1: CCP2 input is controlled by CCP2SEL in the APFCON register.
DS41417A-page 62
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-10: BLOCK DIAGRAM OF RB5
Data Bus
D WR WPUB RD WPUB
D WR PORTB
Q CCP2OUT Enable CCP2OUT 1
Q
VDD Weak
VDD
CK Q RBPU
0
I/O Pin
CK Q VSS
D WR TRISB RD TRISB ANSB<5,3>
Q
CK Q
RD PORTB
D
Q Q D EN
Q3
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB
To Timer1 Gate
To A/D Converter To Cap Sensor
2010 Microchip Technology Inc.
DS41417A-page 63
PIC16F/LF722A/723A
FIGURE 6-11: BLOCK DIAGRAM OF RB6
ICSPTM Mode Debug
Data Bus
D WR WPUB RD WPUB
D WR PORTB
Q
VDD Weak RBPU PORT_ICDCLK
VDD
CK Q
Q
1 0
I/O Pin
CK Q
D WR TRISB RD TRISB RD PORTB
Q
VSS
CK Q
0 1 TRIS_ICDCLK
D
Q Q D EN
Q3
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB
ICSPCLK
DS41417A-page 64
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-12: BLOCK DIAGRAM OF RB7
ICSPTM Mode Debug
Data Bus
D WR WPUB RD WPUB
D WR PORTB
Q
VDD Weak RBPU PORT_ICDDAT
VDD
CK Q
Q
1 0
I/O Pin
CK Q
D WR TRISB RD TRISB RD PORTB
Q
VSS
CK Q
0 1 TRIS_ICDDAT
D
Q Q D EN
Q3
WR IOCB RD IOCB
CK Q
Q
D EN
Interrupt-onChange RD PORTB
ICSPDAT_IN
2010 Microchip Technology Inc.
DS41417A-page 65
PIC16F/LF722A/723A
TABLE 6-2:
Name ADCON0 ANSELB APFCON CCP2CON CPSCON0 CPSCON1 INTCON IOCB OPTION_REG PORTB T1GCON TRISB WPUB Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Bit 7 -- -- -- -- CPSON -- GIE IOCB7 RBPU RB7 TMR1GE TRISB7 WPUB7 Bit 6 -- -- -- -- -- -- PEIE IOCB6 INTEDG RB6 T1GPOL TRISB6 WPUB6 Bit 5 CHS3 ANSB5 -- DC2B1 -- -- T0IE IOCB5 T0CS RB5 T1GTM TRISB5 WPUB5 Bit 4 CHS2 ANSB4 -- DC2B0 -- -- INTE IOCB4 T0SE RB4 T1GSPM TRISB4 WPUB4 Bit 3 CHS1 ANSB3 -- CCP2M3 CPSRNG1 CPSCH3 RBIE IOCB3 PSA RB3 T1GGO/ DONE TRISB3 WPUB3 Bit 2 CHS0 ANSB2 -- CCP2M2 CPSRNG0 CPSCH2 T0IF IOCB2 PS2 RB2 T1GVAL TRISB2 WPUB2 Bit 1 GO/DONE ANSB1 SSSEL CCP2M1 CPSOUT CPSCH1 INTF IOCB1 PS1 RB1 T1GSS1 TRISB1 WPUB1 Bit 0 ADON ANSB0 CCP2SEL CCP2M0 T0XCS CPSCH0 RBIF IOCB0 PS0 RB0 T1GSS0 TRISB0 WPUB0 Value on POR, BOR --00 0000 --11 1111 ---- --00 --00 0000 0--- 0000 ---- 0000 0000 000x 0000 0000 1111 1111 xxxx xxxx 0000 0x00 1111 1111 1111 1111 Value on all other Resets --00 0000 --11 1111 ---- --00 --00 0000 0--- 0000 ---- 0000 0000 000X 0000 0000 1111 1111 xxxx xxxx uuuu uxuu 1111 1111 1111 1111
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by PORTB.
DS41417A-page 66
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
6.4 PORTC and TRISC Registers
PORTC is a 8-bit wide, bidirectional port. The corresponding data direction register is TRISC (Register 6-11). Setting a TRISC bit (= 1) will make the corresponding PORTC pin an input (i.e., put the corresponding output driver in a High-Impedance mode). Clearing a TRISC bit (= 0) will make the corresponding PORTC pin an output (i.e., enable the output driver and put the contents of the output latch on the selected pin). Example 6-3 shows how to initialize PORTC. Reading the PORTC register (Register 6-10) reads the status of the pins, whereas writing to it will write to the PORT latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified and then written to the PORT data latch. The TRISC register (Register 6-11) controls the PORTC pin output drivers, even when they are being used as analog inputs. The user should ensure the bits in the TRISC register are maintained set when using them as analog inputs. I/O pins configured as analog input always read `0'.
EXAMPLE 6-3:
BANKSEL CLRF BANKSEL MOVLW MOVWF
INITIALIZING PORTC
; ;Init PORTC ; ;Set RC<3:2> as inputs ;and set RC<7:4,1:0> ;as outputs
PORTC PORTC TRISC B`00001100' TRISC
The location of the CCP2 function is controlled by the CCP2SEL bit in the APFCON register (refer to Register 6-1).
REGISTER 6-10:
R/W-x RC7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
PORTC: PORTC REGISTER
R/W-x RC6 R/W-x RC5 R/W-x RC4 R/W-x RC3 R/W-x RC2 R/W-x RC1 R/W-x RC0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
RC<7:0>: PORTC General Purpose I/O Pin bits 1 = Port pin is > VIH 0 = Port pin is < VIL
REGISTER 6-11:
R/W-1 TRISC7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
TRISC: PORTC TRI-STATE REGISTER
R/W-1 R/W-1 TRISC5 R/W-1 TRISC4 R/W-1 TRISC3 R/W-1 TRISC2 R/W-1 TRISC1 R/W-1 TRISC0 bit 0
TRISC6
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TRISC<7:0>: PORTC Tri-State Control bits 1 = PORTC pin configured as an input (tri-stated) 0 = PORTC pin configured as an output
2010 Microchip Technology Inc.
DS41417A-page 67
PIC16F/LF722A/723A
6.4.1 RC0/T1OSO/T1CKI 6.4.8 RC7/RX/DT
Figure 6-13 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Timer1 oscillator output * Timer1 clock input Figure 6-20 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Asynchronous serial input * Synchronous serial data I/O
6.4.2
RC1/T1OSI/CCP2
Figure 6-14 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Timer1 oscillator input * Capture 2 input, Compare 2 output, and PWM2 output Note: CCP2 pin location may be selected as RB3 or RC1.
6.4.3
RC2/CCP1
Figure 6-15 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Capture 1 input, Compare 1 output, and PWM1 output
6.4.4
RC3/SCK/SCL
Figure 6-16 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * General purpose I/O SPI clock I2CTM clock
6.4.5
RC4/SDI/SDA
Figure 6-17 shows the diagram for this pin. This pin is configurable to function as one of the following: * * * General purpose I/O SPI data input I2C data I/O
6.4.6
RC5/SDO
Figure 6-18 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * SPI data output
6.4.7
RC6/TX/CK
Figure 6-19 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose I/O * Asynchronous serial output * Synchronous clock I/O
DS41417A-page 68
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-13: BLOCK DIAGRAM OF RC0
Data Bus
Oscillator Circuit RC1/T1OSI D Q
VDD
WR PORTC
CK Q D Q VSS
I/O Pin
WR TRISC RD TRISC T1OSCEN
CK Q
RD PORTC To Timer1 CLK Input
FIGURE 6-14:
BLOCK DIAGRAM OF RC1
CCP2OUT Enable CCP2OUT 1 D Q 0 I/O Pin Oscillator Circuit RC0/T1OSO
Data Bus
VDD
WR PORTC
CK Q D Q VSS
WR TRISC RD TRISC T1OSCEN
CK Q
RD PORTC To CCP2(1) Input
Note
1: CCP2 input is controlled by CCP2SEL in the APFCON register.
2010 Microchip Technology Inc.
DS41417A-page 69
PIC16F/LF722A/723A
FIGURE 6-15: BLOCK DIAGRAM OF RC2
CCP1OUT Enable CCP1OUT 1 D WR PORTC Q 0 I/O Pin
Data Bus
VDD
CK Q D Q VSS
WR TRISC RD TRISC RD PORTC
CK Q
To CCP1 Input
FIGURE 6-16:
BLOCK DIAGRAM OF RC3
SSPM = SPI Mode SCK_MASTER
Data Bus
1 0
SSPEN 1 0
(2)
VDD
D WR PORTC
Q
I/O Pin
CK Q
SCL
D WR TRISC RD TRISC Q CK Q
VSS
To SSP SPI CLOCK Input
1 0 RD PORTC 0 1
SSPEN SSPM = I2CTM Mode
TO SSP I2CTM SCL Input
I2CTM(1)
Note
1: I2CTM Schmitt Trigger has special input levels. 2: I2CTM Slew Rate limiting controlled by SMP bit of SSPSTAT register.
DS41417A-page 70
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 6-17: BLOCK DIAGRAM OF RC4
SSPEN SSPM = I2CTM Mode
Data Bus
VDD
1
D WR PORTC Q
0
(2)
I/O Pin
CK Q VSS D Q
WR TRISC RD TRISC
CK Q
To SSP SPI Data Input
1 0 RD PORTC 0 1
SDA from SSP
To SSP I2CTM SDA Input
I2CTM(1)
Note
1: I2CTM Schmitt Trigger has special input levels. 2: I2CTM Slew Rate limiting controlled by SMP bit of SSPSTAT register.
FIGURE 6-18:
BLOCK DIAGRAM OF RC5
VDD
SSPEN SSPM = SPI Mode
Data Bus
SDO 1
D WR PORTC Q
0
I/O Pin
CK Q VSS D Q
WR TRISC RD TRISC RD PORTC
CK Q
SDO EN
2010 Microchip Technology Inc.
DS41417A-page 71
PIC16F/LF722A/723A
FIGURE 6-19: BLOCK DIAGRAM OF RC6
SYNC USART_TX USART_CK Data Bus D WR PORTC Q CK Q D WR TRISC RD TRISC RD PORTC SPEN TXEN CSRC SYNC To USART Sync Clock Input 0 1 Q VSS 0 1 1 0 I/O Pin VDD
CK Q
FIGURE 6-20:
BLOCK DIAGRAM OF RC7
SPEN SYNC
Data Bus
VDD
USART_DT 1
D WR PORTC Q
0
I/O Pin
CK Q
D WR TRISC RD TRISC RD PORTC
Q
VSS
CK Q
SPEN SYNC TXEN SREN CREN
To USART Data Input
DS41417A-page 72
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 6-3:
Name APFCON CCP1CON CCP2CON PORTC RCSTA SSPCON SSPSTAT T1CON TXSTA TRISC Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Bit 7 -- -- -- RC7 SPEN WCOL SMP TMR1CS1 CSRC TRISC7 Bit 6 -- -- -- RC6 RX9 SSPOV CKE TMR1CS0 TX9 TRISC6 Bit 5 -- DC1B1 DC2B1 RC5 SREN SSPEN D/A T1CKPS1 TXEN TRISC5 Bit 4 -- DC1B0 DC2B0 RC4 CREN CKP P Bit 3 -- CCP1M3 CCP2M3 RC3 ADDEN SSPM3 S Bit 2 -- CCP1M2 CCP2M2 RC2 FERR SSPM2 R/W T1SYNC BRGH TRISC2 Bit 1 SSSEL CCP1M1 CCP2M1 RC1 OERR SSPM1 UA -- TRMT TRISC1 Bit 0 CCP2SEL CCP1M0 CCP2M0 RC0 RX9D SSPM0 BF TMR1ON TX9D TRISC0 Value on POR, BOR ---- --00 --00 0000 --00 0000 xxxx xxxx 0000 000x 0000 0000 0000 0000 0000 00-0 0000 -010 1111 1111 Value on all other Resets ---- --00 --00 0000 --00 0000 xxxx xxxx 0000 000x 0000 0000 0000 0000 uuuu uu-u 0000 -010 1111 1111
T1CKPS0 T1OSCEN SYNC TRISC4 -- TRISC3
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by PORTB.
2010 Microchip Technology Inc.
DS41417A-page 73
PIC16F/LF722A/723A
6.5 PORTE and TRISE Registers
PORTE(1) is an 1-bit wide, input only port. RE3 is input only and its TRIS bit will always read as `1'. Reading the PORTE register (Register 6-12) reads the status of the pins. RE3 reads `0' when MCLRE = 1.
REGISTER 6-12:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-4 bit 3
PORTE: PORTE REGISTER
U-0 -- U-0 -- U-0 -- R-x RE3 U-0 -- U-0 -- U-0 -- bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' RE3: PORTE I/O Pin bits(1) 1 = Port pin is > VIH 0 = Port pin is < VIL Unimplemented: Read as `0'
bit 2-0
REGISTER 6-13:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-4 bit 3 bit 2-0
TRISE: PORTE TRI-STATE REGISTER
U-0 -- U-0 -- U-0 -- R-1 TRISE3 U-0 -- U-0 -- U-0 -- bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' TRISE3: RE3 Port Tri-state Control bit This bit is always `1' as RE3 is an input only Unimplemented: Read as `0'
TABLE 6-4:
Name PORTE TRISE Legend: Note 1: Bit 7 -- --
SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Bit 6 -- -- Bit 5 -- -- Bit 4 -- -- Bit 3 RE3 TRISE3(1) Bit 2 -- -- Bit 1 -- -- Bit 0 -- -- Value on POR, BOR ---- x------ 1--Value on all other Resets ---- x------ 1---
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by PORTE This bit is always `1' as RE3 is input only.
DS41417A-page 74
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
6.5.1 RE3/MCLR/VPP
Figure 6-21 shows the diagram for this pin. This pin is configurable to function as one of the following: * General purpose input * Master Clear Reset with weak pull-up * Programming voltage reference input
FIGURE 6-21:
BLOCK DIAGRAM OF RE3
VDD
ICSPTM Mode Detect
Weak
In-Circuit Serial ProgrammingTM Mode
High-Voltage Detect
I/O Pin
MCLR Circuit
Data Bus RD TRISE VSS RD PORTE
MCLR Pulse Filter
VSS
Power for Programming Flash
2010 Microchip Technology Inc.
DS41417A-page 75
PIC16F/LF722A/723A
NOTES:
DS41417A-page 76
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
7.0
7.1
OSCILLATOR MODULE
Overview
Clock source modes are configured by the FOSC bits in Configuration Word 1 (CONFIG1). The oscillator module can be configured for one of eight modes of operation. 1. 2. 3. 4. 5. 6. 7. 8. RC - External Resistor-Capacitor (RC) with FOSC/4 output on OSC2/CLKOUT. RCIO - External Resistor-Capacitor (RC) with I/O on OSC2/CLKOUT. INTOSC - Internal oscillator with FOSC/4 output on OSC2 and I/O on OSC1/CLKIN. INTOSCIO - Internal oscillator with I/O on OSC1/CLKIN and OSC2/CLKOUT. EC - External clock with I/O on OSC2/CLKOUT. HS - High Gain Crystal or Ceramic Resonator mode. XT - Medium Gain Crystal or Ceramic Resonator Oscillator mode. LP - Low-Power Crystal mode.
The oscillator module has a wide variety of clock sources and selection features that allow it to be used in a wide range of applications while maximizing performance and minimizing power consumption. Figure 7-1 illustrates a block diagram of the oscillator module. Clock sources can be configured from external oscillators, quartz crystal resonators, ceramic resonators and Resistor-Capacitor (RC) circuits. In addition, the system can be configured to use an internal calibrated high-frequency oscillator as clock source, with a choice of selectable speeds via software.
FIGURE 7-1:
SIMPLIFIED PIC(R) MCU CLOCK SOURCE BLOCK DIAGRAM
FOSC<2:0> (Configuration Word 1)
External Oscillator OSC2 Sleep OSC1
LP, XT, HS, RC, EC MUX
Internal Oscillator 500 kHz 0 MUX
IRCF<1:0> (OSCCON Register)
System Clock (CPU and Peripherals)
INTOSC
16 MHz/500 kHz
11
32x PLL
1 Postscaler
8 MHz/250 kHz
10 MUX 01 00
4 MHz/125 kHz
2 MHz/62.5 kHz
PLLEN (Configuration Word 1)
2010 Microchip Technology Inc.
DS41417A-page 77
PIC16F/LF722A/723A
7.2 Clock Source Modes
7.3.2 FREQUENCY SELECT BITS (IRCF)
Clock source modes can be classified as external or internal. * Internal clock source (INTOSC) is contained within the oscillator module and derived from a 500 kHz high precision oscillator. The oscillator module has eight selectable output frequencies, with a maximum internal frequency of 16 MHz. * External clock modes rely on external circuitry for the clock source. Examples are: oscillator modules (EC mode), quartz crystal resonators or ceramic resonators (LP, XT and HS modes) and Resistor-Capacitor (RC) mode circuits. The system clock can be selected between external or internal clock sources via the FOSC bits of the Configuration Word 1. The output of the 500 kHz INTOSC and 16 MHz INTOSC, with Phase Locked Loop enabled, connect to a postscaler and multiplexer (see Figure 7-1). The Internal Oscillator Frequency Select bits (IRCF) of the OSCCON register select the frequency output of the internal oscillator. Depending upon the PLLEN bit, one of four frequencies of two frequency sets can be selected via software: If PLLEN = 1, frequency selection is as follows: * * * * * * * * 16 MHz 8 MHz (Default after Reset) 4 MHz 2 MHz 500 kHz 250 kHz (Default after Reset) 125 kHz 62.5 kHz Note: Following any Reset, the IRCF<1:0> bits of the OSCCON register are set to `10' and the frequency selection is set to 8 MHz or 250 kHz. The user can modify the IRCF bits to select a different frequency.
If PLLEN = 0, frequency selection is as follows:
7.3
Internal Clock Modes
The oscillator module has eight output frequencies derived from a 500 kHz high precision oscillator. The IRCF bits of the OSCCON register select the postscaler applied to the clock source dividing the frequency by 1, 2, 4 or 8. Setting the PLLEN bit of the Configuration Word 1 locks the internal clock source to 16 MHz before the postscaler is selected by the IRCF bits. The PLLEN bit must be set or cleared at the time of programming; therefore, only the upper or low four clock source frequencies are selectable in software.
7.3.1
INTOSC AND INTOSCIO MODES
There is no start-up delay before a new frequency selected in the IRCF bits takes effect. This is because the old and new frequencies are derived from INTOSC via the postscaler and multiplexer. Start-up delay specifications are located in Table 23-2 in Section 23.0 "Electrical Specifications".
The INTOSC and INTOSCIO modes configure the internal oscillators as the system clock source when the device is programmed using the oscillator selection or the FOSC<2:0> bits in the CONFIG1 register. See Section 8.0 "Device Configuration" for more information. In INTOSC mode, OSC1/CLKIN is available for general purpose I/O. OSC2/CLKOUT outputs the selected internal oscillator frequency divided by 4. The CLKOUT signal may be used to provide a clock for external circuitry, synchronization, calibration, test or other application requirements. In INTOSCIO mode, OSC1/CLKIN and OSC2/ CLKOUT are available for general purpose I/O.
DS41417A-page 78
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
7.4 Oscillator Control
The Oscillator Control (OSCCON) register (Figure 7-1) displays the status and allows frequency selection of the internal oscillator (INTOSC) system clock. The OSCCON register contains the following bits: * Frequency selection bits (IRCF) * Status Locked bits (ICSL) * Status Stable bits (ICSS)
REGISTER 7-1:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR
OSCCON: OSCILLATOR CONTROL REGISTER
U-0 -- R/W-1 IRCF1 R/W-0 IRCF0 R-q ICSL R-q ICSS U-0 -- U-0 -- bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
q = Value depends on condition bit 7-6 bit 5-4 Unimplemented: Read as `0' IRCF<1:0>: Internal Oscillator Frequency Select bits
When PLLEN = 1 (16 MHz INTOSC) 11 = 16 MHz 10 = 8 MHz (POR value) 01 = 4 MHz 00 = 2 MHz When PLLEN = 0 (500 kHz INTOSC) 11 = 500 kHz 10 = 250 kHz (POR value) 01 = 125 kHz 00 = 62.5 kHz
bit 3
ICSL: Internal Clock Oscillator Status Locked bit (2% Stable) 1 = 16 MHz/500 kHz Internal Oscillator (HFIOSC) is in lock 0 = 16 MHz/500 kHz Internal Oscillator (HFIOSC) has not yet locked ICSS: Internal Clock Oscillator Status Stable bit (0.5% Stable) 1 = 16 MHz/500 kHz Internal Oscillator (HFIOSC) has stabilized to its maximum accuracy 0 = 16 MHz/500 kHz Internal Oscillator (HFIOSC) has not yet reached its maximum accuracy Unimplemented: Read as `0'
bit 2
bit 1-0
2010 Microchip Technology Inc.
DS41417A-page 79
PIC16F/LF722A/723A
7.5 Oscillator Tuning
The INTOSC is factory calibrated but can be adjusted in software by writing to the OSCTUNE register (Register 7-2). The default value of the OSCTUNE register is `0'. The value is a 6-bit two's complement number. When the OSCTUNE register is modified, the INTOSC frequency will begin shifting to the new frequency. Code execution continues during this shift. There is no indication that the shift has occurred.
REGISTER 7-2:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-0
OSCTUNE: OSCILLATOR TUNING REGISTER
U-0 -- R/W-0 TUN5 R/W-0 TUN4 R/W-0 TUN3 R/W-0 TUN2 R/W-0 TUN1 R/W-0 TUN0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' TUN<5:0>: Frequency Tuning bits 01 1111 = Maximum frequency 01 1110 = * * * 00 0001 = 00 0000 = Oscillator module is running at the factory-calibrated frequency. 11 1111 = * * * 10 0000 = Minimum frequency
DS41417A-page 80
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
7.6
7.6.1
External Clock Modes
OSCILLATOR START-UP TIMER (OST)
If the oscillator module is configured for LP, XT or HS modes, the Oscillator Start-up Timer (OST) counts 1024 oscillations on the OSC1 pin before the device is released from Reset. This occurs following a Power-on Reset (POR) and when the Power-up Timer (PWRT) has expired (if configured), or a wake-up from Sleep. During this time, the program counter does not increment and program execution is suspended. The OST ensures that the oscillator circuit, using a quartz crystal resonator or ceramic resonator, has started and is providing a stable system clock to the oscillator module.
XT Oscillator mode selects the intermediate gain setting of the internal inverter-amplifier. XT mode current consumption is the medium of the three modes. This mode is best suited to drive resonators with a medium drive level specification. HS Oscillator mode selects the highest gain setting of the internal inverter-amplifier. HS mode current consumption is the highest of the three modes. This mode is best suited for resonators that require a high drive setting. Figure 7-3 and Figure 7-4 show typical circuits for quartz crystal and ceramic resonators, respectively.
FIGURE 7-3:
QUARTZ CRYSTAL OPERATION (LP, XT OR HS MODE)
PIC(R) MCU
OSC1/CLKIN
7.6.2
EC MODE
The External Clock (EC) mode allows an externally generated logic level as the system clock source. When operating in this mode, an external clock source is connected to the OSC1 input and the OSC2 is available for general purpose I/O. Figure 7-2 shows the pin connections for EC mode. The Oscillator Start-up Timer (OST) is disabled when EC mode is selected. Therefore, there is no delay in operation after a Power-on Reset (POR) or wake-up from Sleep. Because the PIC(R) MCU design is fully static, stopping the external clock input will have the effect of halting the device while leaving all data intact. Upon restarting the external clock, the device will resume operation as if no time had elapsed.
C1 Quartz Crystal RF(2)
To Internal Logic Sleep
C2
RS(1)
OSC2/CLKOUT
Note 1: 2:
A series resistor (RS) may be required for quartz crystals with low drive level. The value of RF varies with the Oscillator mode selected.
FIGURE 7-2:
EXTERNAL CLOCK (EC) MODE OPERATION
OSC1/CLKIN PIC(R) MCU I/O OSC2/CLKOUT(1)
Clock from Ext. System
Note 1: Quartz crystal characteristics vary according to type, package and manufacturer. The user should consult the manufacturer data sheets for specifications and recommended application. 2: Always verify oscillator performance over the VDD and temperature range that is expected for the application. 3: For oscillator design assistance, reference the following Microchip Applications Notes: * AN826, "Crystal Oscillator Basics and Crystal Selection for rfPIC(R) and PIC(R) Devices" (DS00826) * AN849, "Basic PIC(R) Oscillator Design" (DS00849) * AN943, "Practical PIC(R) Oscillator Analysis and Design" (DS00943) * AN949, "Making Your Oscillator Work" (DS00949)
Note 1:
Alternate pin functions are described in Section 6.1 "Alternate Pin Function".
7.6.3
LP, XT, HS MODES
The LP, XT and HS modes support the use of quartz crystal resonators or ceramic resonators connected to OSC1 and OSC2 (Figure 7-3). The mode selects a low, medium or high gain setting of the internal inverteramplifier to support various resonator types and speed. LP Oscillator mode selects the lowest gain setting of the internal inverter-amplifier. LP mode current consumption is the least of the three modes. This mode is best suited to drive resonators with a low drive level specification, for example, tuning fork type crystals.
2010 Microchip Technology Inc.
DS41417A-page 81
PIC16F/LF722A/723A
FIGURE 7-4: CERAMIC RESONATOR OPERATION (XT OR HS MODE)
PIC(R) MCU
OSC1/CLKIN C1
FIGURE 7-5:
VDD REXT
EXTERNAL RC MODES
PIC(R) MCU
OSC1/CLKIN CEXT
To Internal Logic RP(3) RF
(2)
Internal Clock
VSS FOSC/4 or I/O(2) OSC2/CLKOUT(1)
Sleep
C2 Ceramic RS(1) Resonator
OSC2/CLKOUT
Note 1: A series resistor (RS) may be required for ceramic resonators with low drive level. 2: The value of RF varies with the Oscillator mode selected. 3: An additional parallel feedback resistor (RP) may be required for proper ceramic resonator operation.
Recommended values: 10 k REXT 100 k, <3V 3 k REXT 100 k, 3-5V CEXT > 20 pF, 2-5V Note 1: 2: Alternate pin functions are described in Section 6.1 "Alternate Pin Function". Output depends upon RC or RCIO clock mode.
In RCIO mode, the RC circuit is connected to OSC1. OSC2 becomes an additional general purpose I/O pin. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values and the operating temperature. Other factors affecting the oscillator frequency are: * threshold voltage variation * component tolerances * packaging variations in capacitance The user also needs to take into account variation due to tolerance of external RC components used.
7.6.4
EXTERNAL RC MODES
The external Resistor-Capacitor (RC) modes support the use of an external RC circuit. This allows the designer maximum flexibility in frequency choice while keeping costs to a minimum when clock accuracy is not required. There are two modes: RC and RCIO. In RC mode, the RC circuit connects to OSC1. OSC2/ CLKOUT outputs the RC oscillator frequency divided by 4. This signal may be used to provide a clock for external circuitry, synchronization, calibration, test or other application requirements. Figure 7-5 shows the external RC mode connections.
TABLE 7-1:
Name CONFIG1(1) OSCCON OSCTUNE Legend: Note 1:
SUMMARY OF REGISTERS ASSOCIATED WITH CLOCK SOURCES
Bit 7 -- -- -- Bit 6 CP -- -- Bit 5 MCLRE IRCF1 TUN5 Bit 4 PWRTE IRCF0 TUN4 Bit 3 WDTE ICSL TUN3 Bit 2 FOSC2 ICSS TUN2 Bit 1 FOSC1 -- TUN1 Bit 0 FOSC0 -- TUN0 Value on POR, BOR -- --10 qq---00 0000 Value on all other Resets(1) -- --10 qq---uu uuuu
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by oscillators. See Configuration Word 1 (Register 8-1) for operation of all bits.
DS41417A-page 82
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
8.0 DEVICE CONFIGURATION
8.1 Configuration Words
Device configuration consists of Configuration Word 1 and Configuration Word 2 registers, code protection and device ID. There are several Configuration Word bits that allow different oscillator and memory protection options. These are implemented as Configuration Word 1 register at 2007h and Configuration Word 2 register at 2008h. These registers are only accessible during programming.
REGISTER 8-1:
-- bit 15 U-1(4) -- bit 7 Legend: R = Readable bit -n = Value at POR bit 13
CONFIG1: CONFIGURATION WORD REGISTER 1
R/P-1 -- DEBUG R/P-1 PLLEN U-1(4) -- R/P-1 BORV R/P-1 BOREN1 R/P-1 BOREN0 bit 8 R/P-1 CP R/P-1 MCLRE R/P-1 PWRTE R/P-1 WDTE R/P-1 FOSC2 R/P-1 FOSC1 R/P-1 FOSC0 bit 0 P = Programmable bit W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
DEBUG: In-Circuit Debugger Mode bit 1 = In-circuit debugger disabled, RB6/ICSPCLK and RB7/ICSPDAT are general purpose I/O pins 0 = In-circuit debugger enabled, RB6/ICSPCLK and RB7/ICSPDAT are dedicated to the debugger PLLEN: INTOSC PLL Enable bit 0 = INTOSC frequency is 500 kHz 1 = INTOSC frequency is 16 MHz (32x) Unimplemented: Read as `1' BORV: Brown-out Reset Voltage selection bit 0 = Brown-out Reset Voltage (VBOR) set to 2.5 V nominal 1 = Brown-out Reset Voltage (VBOR) set to 1.9 V nominal BOREN<1:0>: Brown-out Reset Selection bits(1) 0x = BOR disabled (preconditioned state) 10 = BOR enabled during operation and disabled in Sleep 11 = BOR enabled Unimplemented: Read as `1' CP: Code Protection bit(2) 1 = Program memory code protection is disabled 0 = Program memory code protection is enabled MCLRE: RE3/MCLR Pin Function Select bit(3) 1 = RE3/MCLR pin function is MCLR 0 = RE3/MCLR pin function is digital input, MCLR internally tied to VDD PWRTE: Power-up Timer Enable bit 1 = PWRT disabled 0 = PWRT enabled WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled Enabling Brown-out Reset does not automatically enable Power-up Timer. The entire program memory will be erased when the code protection is turned off. When MCLR is asserted in INTOSC or RC mode, the internal clock oscillator is disabled. MPLAB(R) IDE masks unimplemented Configuration bits to `0'.
bit 12
bit 11 bit 10
bit 9-8
bit 7 bit 6
bit 5
bit 4
bit 3
Note 1: 2: 3: 4:
2010 Microchip Technology Inc.
DS41417A-page 83
PIC16F/LF722A/723A
REGISTER 8-1:
bit 2-0
CONFIG1: CONFIGURATION WORD REGISTER 1 (CONTINUED)
FOSC<2:0>: Oscillator Selection bits 111 = RC oscillator: CLKOUT function on RA6/OSC2/CLKOUT pin, RC on RA7/OSC1/CLKIN 110 = RCIO oscillator: I/O function on RA6/OSC2/CLKOUT pin, RC on RA7/OSC1/CLKIN 101 = INTOSC oscillator: CLKOUT function on RA6/OSC2/CLKOUT pin, I/O function on RA7/OSC1/CLKIN 100 = INTOSCIO oscillator: I/O function on RA6/OSC2/CLKOUT pin, I/O function on RA7/OSC1/CLKIN 011 = EC: I/O function on RA6/OSC2/CLKOUT pin, CLKIN on RA7/OSC1/CLKIN 010 = HS oscillator: High-speed crystal/resonator on RA6/OSC2/CLKOUT and RA7/OSC1/CLKIN 001 = XT oscillator: Crystal/resonator on RA6/OSC2/CLKOUT and RA7/OSC1/CLKIN 000 = LP oscillator: Low-power crystal on RA6/OSC2/CLKOUT and RA7/OSC1/CLKIN Enabling Brown-out Reset does not automatically enable Power-up Timer. The entire program memory will be erased when the code protection is turned off. When MCLR is asserted in INTOSC or RC mode, the internal clock oscillator is disabled. MPLAB(R) IDE masks unimplemented Configuration bits to `0'.
Note 1: 2: 3: 4:
REGISTER 8-2:
-- bit 15 U-1(1) -- bit 7 Legend: R = Readable bit -n = Value at POR bit 13-6 bit 5-4
CONFIG2: CONFIGURATION WORD REGISTER 2
U-1(1) -- -- U-1(1) -- U-1(1) -- U-1(1) -- U-1(1) -- U-1(1) -- bit 8 U-1(1) -- R/P-1 VCAPEN1 R/P-1 VCAPEN0 U-1(1) -- U-1(1) -- U-1(1) -- U-1(1) -- bit 0 P = Programmable bit W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `1' VCAPEN<1:0>: Voltage Regulator Capacitor Enable bits For the PIC16LF722A/723A: These bits are ignored. All VCAP pin functions are disabled. For the PIC16F722A/723A: 00 = VCAP functionality is enabled on RA0 01 = VCAP functionality is enabled on RA5 10 = VCAP functionality is enabled on RA6 11 = All VCAP functions are disabled (not recommended) Unimplemented: Read as `1' MPLAB(R) IDE masks unimplemented Configuration bits to `0'.
bit 3-0 Note 1:
DS41417A-page 84
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
8.2 Code Protection
If the code protection bit(s) have not been programmed, the on-chip program memory can be read out using ICSPTM for verification purposes. Note: The entire Flash program memory will be erased when the code protection is turned off. See the "PIC16F72X/PIC16LF72X Memory Programming Specification" (DS41332) for more information.
8.3
User ID
Four memory locations (2000h-2003h) are designated as ID locations where the user can store checksum or other code identification numbers. These locations are not accessible during normal execution, but are readable and writable during Program/Verify mode. Only the Least Significant 7 bits of the ID locations are reported when using MPLAB IDE. See the "PIC16F72X/PIC16LF72X Memory Programming Specification" (DS41332) for more information.
2010 Microchip Technology Inc.
DS41417A-page 85
PIC16F/LF722A/723A
NOTES:
DS41417A-page 86
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
9.0 ANALOG-TO-DIGITAL CONVERTER (ADC) MODULE
The Analog-to-Digital Converter (ADC) allows conversion of an analog input signal to a 8-bit binary representation of that signal. This device uses analog inputs, which are multiplexed into a single sample and hold circuit. The output of the sample and hold is connected to the input of the converter. The converter generates a 8-bit binary result via successive approximation and stores the conversion result into the ADC result register (ADRES). Figure 9-1 shows the block diagram of the ADC. The ADC voltage reference is software selectable to be either internally generated or externally supplied. The ADC can generate an interrupt upon completion of a conversion. This interrupt can be used to wake-up the device from Sleep.
FIGURE 9-1:
ADC BLOCK DIAGRAM
AVDD ADREF = 0x ADREF = 11 VREF+ AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 Reserved Reserved Reserved Reserved FVREF 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ADON VSS ADRES GO/DONE ADC 8 ADREF = 10
CHS<3:0>
2010 Microchip Technology Inc.
DS41417A-page 87
PIC16F/LF722A/723A
9.1 ADC Configuration
When configuring and using the ADC the following functions must be considered: * * * * * * Port configuration Channel selection ADC voltage reference selection ADC conversion clock source Interrupt control Results formatting For correct conversion, the appropriate TAD specification must be met. Refer to the A/D conversion requirements in Section 23.0 "Electrical Specifications" for more information. Table 9-1 gives examples of appropriate ADC clock selections. Note: Unless using the FRC, any changes in the system clock frequency will change the ADC clock frequency, which may adversely affect the ADC result.
9.1.1
PORT CONFIGURATION
The ADC can be used to convert both analog and digital signals. When converting analog signals, the I/O pin should be configured for analog by setting the associated TRIS and ANSEL bits. Refer to Section 6.0 "I/O Ports" for more information. Note: Analog voltages on any pin that is defined as a digital input may cause the input buffer to conduct excess current.
9.1.2
CHANNEL SELECTION
The CHS bits of the ADCON0 register determine which channel is connected to the sample and hold circuit. When changing channels, a delay is required before starting the next conversion. Refer to Section 9.2 "ADC Operation" for more information.
9.1.3
ADC VOLTAGE REFERENCE
The ADREF bits of the ADCON1 register provides control of the positive voltage reference. The positive voltage reference can be either VDD, an external voltage source or the internal Fixed Voltage Reference. The negative voltage reference is always connected to the ground reference. See Section 10.0 "Fixed Voltage Reference" for more details.
9.1.4
CONVERSION CLOCK
The source of the conversion clock is software selectable via the ADCS bits of the ADCON1 register. There are seven possible clock options: * * * * * * * FOSC/2 FOSC/4 FOSC/8 FOSC/16 FOSC/32 FOSC/64 FRC (dedicated internal oscillator)
The time to complete one bit conversion is defined as TAD. One full 8-bit conversion requires 10 TAD periods as shown in Figure 9-2.
DS41417A-page 88
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 9-1:
ADC Clock Source Fosc/2 Fosc/4 Fosc/8 Fosc/16 Fosc/32 Fosc/64 FRC Legend: Note 1: 2: 3: 4:
ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES
Device Frequency (FOSC) 20 MHz 100 ns(2) 200 ns 400 ns
(2) (2)
ADC Clock Period (TAD) ADCS<2:0> 000 100 001 101 010 110 x11
16 MHz 125 ns(2) 250 ns 0.5 s
(2) (2)
8 MHz 250 ns(2) 500 ns
(2)
4 MHz 500 ns(2) 1.0 s 2.0 s 4.0 s 8.0 s(3) 16.0 s
(3)
1 MHz 2.0 s 4.0 s 8.0 s(3) 16.0 s(3) 32.0 s(3) 64.0 s(3) 1.0-6.0 s(1,4)
1.0 s 2.0 s 4.0 s 8.0 s
(3)
800 ns 1.6 s 3.2 s 1.0-6.0 s(1,4)
1.0 s 2.0 s 4.0 s 1.0-6.0 s(1,4)
1.0-6.0 s(1,4)
1.0-6.0 s(1,4)
Shaded cells are outside of recommended range. The FRC source has a typical TAD time of 1.6 s for VDD. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. When the device frequency is greater than 1 MHz, the FRC clock source is only recommended if the conversion will be performed during Sleep.
FIGURE 9-2:
Tcy to TAD TAD0
ANALOG-TO-DIGITAL CONVERSION TAD CYCLES
TAD1 TAD2 b7 Conversion Starts Holding Capacitor is Disconnected from Analog Input (typically 100 ns) TAD3 b6
TAD4
TAD5 b4
TAD6 b3
TAD7
TAD8
TAD9
b5
b2
b1
b0
Set GO/DONE bit
ADRES register is loaded, GO/DONE bit is cleared, ADIF bit is set, Holding capacitor is connected to analog input
2010 Microchip Technology Inc.
DS41417A-page 89
PIC16F/LF722A/723A
9.1.5 INTERRUPTS 9.2.3 TERMINATING A CONVERSION
The ADC module allows for the ability to generate an interrupt upon completion of an Analog-to-Digital conversion. The ADC interrupt flag is the ADIF bit in the PIR1 register. The ADC interrupt enable is the ADIE bit in the PIE1 register. The ADIF bit must be cleared in software. Note 1: The ADIF bit is set at the completion of every conversion, regardless of whether or not the ADC interrupt is enabled. 2: The ADC operates during Sleep only when the FRC oscillator is selected. This interrupt can be generated while the device is operating or while in Sleep. If the device is in Sleep, the interrupt will wake-up the device. Upon waking from Sleep, the next instruction following the SLEEP instruction is always executed. If the user is attempting to wake-up from Sleep and resume in-line code execution, the GIE and PEIE bits of the INTCON register must be disabled. If the GIE and PEIE bits of the INTCON register are enabled, execution will switch to the Interrupt Service Routine. Please refer to Section 9.1.5 "Interrupts" for more information. If a conversion must be terminated before completion, the GO/DONE bit can be cleared in software. The ADRES register will be updated with the partially complete Analog-to-Digital conversion sample. Incomplete bits will match the last bit converted. Note: A device Reset forces all registers to their Reset state. Thus, the ADC module is turned off and any pending conversion is terminated.
9.2.4
ADC OPERATION DURING SLEEP
The ADC module can operate during Sleep. This requires the ADC clock source to be set to the FRC option. When the FRC clock source is selected, the ADC waits one additional instruction before starting the conversion. This allows the SLEEP instruction to be executed, which can reduce system noise during the conversion. If the ADC interrupt is enabled, the device will wake-up from Sleep when the conversion completes. If the ADC interrupt is disabled, the ADC module is turned off after the conversion completes, although the ADON bit remains set. When the ADC clock source is something other than FRC, a SLEEP instruction causes the present conversion to be aborted and the ADC module is turned off, although the ADON bit remains set.
9.2
9.2.1
ADC Operation
STARTING A CONVERSION
9.2.5
SPECIAL EVENT TRIGGER
To enable the ADC module, the ADON bit of the ADCON0 register must be set to a `1'. Setting the GO/ DONE bit of the ADCON0 register to a `1' will start the Analog-to-Digital conversion. Note: The GO/DONE bit should not be set in the same instruction that turns on the ADC. Refer to Section 9.2.6 "A/D Conversion Procedure".
The Special Event Trigger of the CCP module allows periodic ADC measurements without software intervention. When this trigger occurs, the GO/DONE bit is set by hardware and the Timer1 counter resets to zero. Using the Special Event Trigger does not assure proper ADC timing. It is the user's responsibility to ensure that the ADC timing requirements are met. Refer to Section 15.0 "Capture/Compare/PWM (CCP) Module" for more information.
9.2.2
COMPLETION OF A CONVERSION
When the conversion is complete, the ADC module will: * Clear the GO/DONE bit * Set the ADIF Interrupt Flag bit * Update the ADRES register with new conversion result
DS41417A-page 90
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
9.2.6 A/D CONVERSION PROCEDURE EXAMPLE 9-1: A/D CONVERSION
This is an example procedure for using the ADC to perform an Analog-to-Digital conversion: 1. Configure Port: * Disable pin output driver (Refer to the TRIS register) * Configure pin as analog (Refer to the ANSEL register) Configure the ADC module: * Select ADC conversion clock * Configure voltage reference * Select ADC input channel * Turn on ADC module Configure ADC interrupt (optional): * Clear ADC interrupt flag * Enable ADC interrupt * Enable peripheral interrupt * Enable global interrupt(1) Wait the required acquisition time(2). Start conversion by setting the GO/DONE bit. Wait for ADC conversion to complete by one of the following: * Polling the GO/DONE bit * Waiting for the ADC interrupt (interrupts enabled) Read ADC Result. Clear the ADC interrupt flag (required if interrupt is enabled). Note 1: The global interrupt can be disabled if the user is attempting to wake-up from Sleep and resume in-line code execution. 2: Refer to Section 9.3 "A/D Acquisition Requirements".
;This code block configures the ADC ;for polling, Vdd reference, Frc clock ;and AN0 input. ; ;Conversion start & polling for completion ; are included. ; BANKSEL ADCON1 ; MOVLW B'01110000' ;ADC Frc clock, ;VDD reference MOVWF ADCON1 ; BANKSEL TRISA ; BSF TRISA,0 ;Set RA0 to input BANKSEL ANSELA ; BSF ANSELA,0 ;Set RA0 to analog BANKSEL ADCON0 ; MOVLW B'00000001';AN0, On MOVWF ADCON0 ; CALL SampleTime ;Acquisiton delay BSF ADCON0,GO ;Start conversion BTFSC ADCON0,GO ;Is conversion done? GOTO $-1 ;No, test again BANKSEL ADRES ; MOVF ADRES,W ;Read result MOVWF RESULT ;store in GPR space
2.
3.
4. 5. 6.
7. 8.
2010 Microchip Technology Inc.
DS41417A-page 91
PIC16F/LF722A/723A
9.2.7 ADC REGISTER DEFINITIONS
The following registers are used to control the operation of the ADC.
REGISTER 9-1:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-2
ADCON0: A/D CONTROL REGISTER 0
U-0 -- R/W-0 CHS3 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 R/W-0 GO/DONE R/W-0 ADON bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' CHS<3:0>: Analog Channel Select bits 0000 = AN0 0001 = AN1 0010 = AN2 0011 = AN3 0100 = AN4 0101 = AN5 0110 = AN6 0111 = AN7 1000 = AN8 1001 = AN9 1010 = AN10 1011 = Reserved 1100 = Reserved 1101 = Reserved 1110 = Reserved 1111 = Fixed Voltage Reference (FVREF) GO/DONE: A/D Conversion Status bit 1 = A/D conversion cycle in progress. Setting this bit starts an A/D conversion cycle. This bit is automatically cleared by hardware when the A/D conversion has completed. 0 = A/D conversion completed/not in progress ADON: ADC Enable bit 1 = ADC is enabled 0 = ADC is disabled and consumes no operating current
bit 1
bit 0
DS41417A-page 92
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 9-2:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7 bit 6-4 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
ADCON1: A/D CONTROL REGISTER 1
R/W-0
ADCS2
R/W-0
ADCS1
R/W-0
ADCS0
U-0 --
U-0 --
R/W-0
ADREF1
R/W-0
ADREF0
bit 0
Unimplemented: Read as `0' ADCS<2:0>: A/D Conversion Clock Select bits 000 = FOSC/2 001 = FOSC/8 010 = FOSC/32 011 = FRC (clock supplied from a dedicated RC oscillator) 100 = FOSC/4 101 = FOSC/16 110 = FOSC/64 111 = FRC (clock supplied from a dedicated RC oscillator) Unimplemented: Read as `0' ADREF<1:0>: Voltage Reference Configuration bits 0x = VREF is connected to VDD 10 = VREF is connected to external VREF (RA3/AN3) 11 = VREF is connected to internal Fixed Voltage Reference
bit 3-2 bit 1-0
REGISTER 9-3:
R/W-x ADRES7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
ADRES: ADC RESULT REGISTER
R/W-x ADRES6 R/W-x ADRES5 R/W-x ADRES4 R/W-x ADRES3 R/W-x ADRES2 R/W-x ADRES1 R/W-x ADRES0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
ADRES<7:0>: ADC Result Register bits 8-bit conversion result.
2010 Microchip Technology Inc.
DS41417A-page 93
PIC16F/LF722A/723A
9.3 A/D Acquisition Requirements
For the ADC to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The Analog Input model is shown in Figure 9-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), refer to Figure 9-3. The maximum recommended impedance for analog sources is 10 k. As the source impedance is decreased, the acquisition time may be decreased. After the analog input channel is selected (or changed), an A/D acquisition must be done before the conversion can be started. To calculate the minimum acquisition time, Equation 9-1 may be used. This equation assumes that 1/2 LSb error is used (256 steps for the ADC). The 1/2 LSb error is the maximum error allowed for the ADC to meet its specified resolution.
EQUATION 9-1: Assumptions:
ACQUISITION TIME EXAMPLE Temperature = 50C and external impedance of 10k 5.0V VDD
TACQ = Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient = TAMP + TC + TCOFF = 2s + TC + Temperature - 25C 0.05s/C The value for TC can be approximated with the following equations:
1 VAPPLIED 1 - -------------------------- = VCHOLD n+1 2 -1
--------- RC VAPPLIED 1 - e = VCHOLD - Tc - TC
;[1] VCHOLD charged to within 1/2 lsb
;[2] VCHOLD charge response to VAPPLIED
-------- 1 RC VAPPLIED 1 - e = VAPPLIED 1 - -------------------------- ;combining [1] and [2] n+1 2 -1
Note: Where n = number of bits of the ADC. Solving for TC:
TC = - CHOLD RIC + RSS + RS ln(1/511) = - 10pF 1k + 7k + 10k ln(0.001957) = 1.12 s
Therefore: TACQ = 2s + 1.12s + 50C- 25C 0.05s/C = 4.42s
Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out. 2: The charge holding capacitor (CHOLD) is not discharged after each conversion. 3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification.
DS41417A-page 94
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 9-3: ANALOG INPUT MODEL
VDD Rs VA ANx CPIN 5 pF VT 0.6V RIC 1k I LEAKAGE(1) Sampling Switch SS Rss CHOLD = 10 pF VSS/VREF-
VT 0.6V
Legend: CHOLD CPIN
= Sample/Hold Capacitance = Input Capacitance
6V 5V VDD 4V 3V 2V
RSS
I LEAKAGE = Leakage current at the pin due to various junctions = Interconnect Resistance RIC RSS = Resistance of Sampling Switch SS VT = Sampling Switch = Threshold Voltage
5 6 7 8 9 10 11 Sampling Switch (k)
Note 1: Refer to Section 23.0 "Electrical Specifications".
FIGURE 9-4:
ADC TRANSFER FUNCTION
Full-Scale Range
FFh FEh FDh ADC Output Code FCh FBh Full-Scale Transition 1 LSB ideal
04h 03h 02h 01h 00h 1 LSB ideal VSS Zero-Scale Transition VREF
Analog Input Voltage
2010 Microchip Technology Inc.
DS41417A-page 95
PIC16F/LF722A/723A
TABLE 9-2:
Name ADCON0 ADCON1 ANSELA ANSELB ADRES CCP2CON FVRCON INTCON PIE1 PIR1 TRISA TRISB Legend: -- FVRRDY GIE TMR1GIE TMR1GIF TRISA7 TRISB7 -- FVREN PEIE ADIE ADIF TRISA6 TRISB6 DC2B1 -- T0IE RCIE RCIF TRISA5 TRISB5
SUMMARY OF ASSOCIATED ADC REGISTERS
Bit 7 -- -- -- -- Bit 6 -- ADCS2 -- -- Bit 5 CHS3 ADCS1 ANSA5 ANSB5 Bit 4 CHS2 ADCS0 ANSA4 ANSB4 DC2B0 -- INTE TXIE TXIF TRISA4 TRISB4 Bit 3 CHS1 -- ANSA3 ANSB3 CCP2M3 -- RBIE SSPIE SSPIF TRISA3 TRISB3 Bit 2 CHS0 -- ANSA2 ANSB2 CCP2M2 -- T0IF CCP1IE CCP1IF TRISA2 TRISB2 Bit 1 GO/DONE ADREF1 ANSA1 ANSB1 CCP2M1 ADFVR1 INTF TMR2IE TMR2IF TRISA1 TRISB1 Bit 0 ADON ADREF0 ANSA0 ANSB0 CCP2M0 ADFVR0 RBIF TMR1IE TMR1IF TRISA0 TRISB0 Value on POR, BOR --00 0000 -000 --00 --11 1111 --11 1111 xxxx xxxx --00 0000 q0-- --00 0000 000x 0000 0000 0000 0000 1111 1111 1111 1111 Value on all other Resets --00 0000 -000 --00 --11 1111 --11 1111 uuuu uuuu --00 0000 q0-- --00 0000 000x 0000 0000 0000 0000 1111 1111 1111 1111
A/D Result Register Byte
x = unknown, u = unchanged, -- = unimplemented read as `0', q = value depends on condition. Shaded cells are not used for ADC module.
DS41417A-page 96
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
10.0 FIXED VOLTAGE REFERENCE
This device contains an internal voltage regulator. To provide a reference for the regulator, a band gap reference is provided. This band gap is also user accessible via an A/D converter channel. User level band gap functions are controlled by the FVRCON register, which is shown in Register 10-1.
REGISTER 10-1:
R-q FVRRDY bit 7 Legend: R = Readable bit -n = Value at POR
FVRCON: FIXED VOLTAGE REFERENCE REGISTER
R/W-0 U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 ADFVR1 R/W-0 ADFVR0 bit 0
FVREN
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
q = Value depends on condition bit 7 FVRRDY: Fixed Voltage Reference Ready Flag bit 0 = Fixed Voltage Reference output is not active or stable 1 = Fixed Voltage Reference output is ready for use FVREN(1): Fixed Voltage Reference Enable bit 0 = Fixed Voltage Reference is disabled 1 = Fixed Voltage Reference is enabled Unimplemented: Read as `0' ADFVR<1:0>: A/D Converter Fixed Voltage Reference Selection bits 00 = A/D Converter Fixed Voltage Reference Peripheral output is off. 01 = A/D Converter Fixed Voltage Reference Peripheral output is 1x (1.024V) 10 = A/D Converter Fixed Voltage Reference Peripheral output is 2x (2.048V)(1) 11 = A/D Converter Fixed Voltage Reference Peripheral output is 4x (4.096V)(1)
bit 6
bit 5-2 bit 1-0
Note 1: Fixed Voltage Reference output cannot exceed VDD.
2010 Microchip Technology Inc.
DS41417A-page 97
PIC16F/LF722A/723A
NOTES:
DS41417A-page 98
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
11.0 TIMER0 MODULE
The Timer0 module is an 8-bit timer/counter with the following features: * * * * * * 8-bit timer/counter register (TMR0) 8-bit prescaler (shared with Watchdog Timer) Programmable internal or external clock source Programmable external clock edge selection Interrupt on overflow TMR0 can be used to gate Timer1 When TMR0 is written, the increment is inhibited for two instruction cycles immediately following the write. Note: The value written to the TMR0 register can be adjusted, in order to account for the two instruction cycle delay when TMR0 is written.
11.1.2
8-BIT COUNTER MODE
Figure 11-1 is a block diagram of the Timer0 module.
In 8-Bit Counter mode, the Timer0 module will increment on every rising or falling edge of the T0CKI pin or the Capacitive Sensing Oscillator (CPSOSC) signal. 8-Bit Counter mode using the T0CKI pin is selected by setting the T0CS bit in the OPTION register to `1' and resetting the T0XCS bit in the CPSCON0 register to `0'. 8-Bit Counter Mode using the Capacitive Sensing Oscillator (CPSOSC) signal is selected by setting the T0CS bit in the OPTION register to `1' and setting the T0XCS bit in the CPSCON0 register to `1'. The rising or falling transition of the incrementing edge for either input source is determined by the T0SE bit in the OPTION register.
11.1
Timer0 Operation
The Timer0 module can be used as either an 8-bit timer or an 8-bit counter.
11.1.1
8-BIT TIMER MODE
The Timer0 module will increment every instruction cycle, if used without a prescaler. 8-Bit Timer mode is selected by clearing the T0CS bit of the OPTION register.
FIGURE 11-1:
FOSC/4
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
Data Bus T0XCS T0CKI 0 Cap. Sensing Oscillator T1GSS = 11 TMR1GE PSA WDTE 8 1 0 8-Bit Prescaler 1 0 0 1 SYNC 2 TCY 8 TMR0 Set Flag bit T0IF on Overflow Overflow to Timer1
1
T0SE
T0CS
PSA
Low-Power WDT OSC Divide by 512
PS<2:0>
1 WDT Time-out 0 PSA
2010 Microchip Technology Inc.
DS41417A-page 99
PIC16F/LF722A/723A
11.1.3 SOFTWARE PROGRAMMABLE PRESCALER
A single software programmable prescaler is available for use with either Timer0 or the Watchdog Timer (WDT), but not both simultaneously. The prescaler assignment is controlled by the PSA bit of the OPTION register. To assign the prescaler to Timer0, the PSA bit must be cleared to a `0'. There are 8 prescaler options for the Timer0 module ranging from 1:2 to 1:256. The pres ca le values are selectable via the PS<2:0> bits of the OPTION register. In order to have a 1:1 prescaler value for the Timer0 module, the prescaler must be assigned to the WDT module. The prescaler is not readable or writable. When assigned to the Timer0 module, all instructions writing to the TMR0 register will clear the prescaler. Note: When the prescaler is assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT.
11.1.4
TIMER0 INTERRUPT
Timer0 will generate an interrupt when the TMR0 register overflows from PH to 00h. The T0IF interrupt flag bit of the INTCON register is set every time the TMR0 register overflows, regardless of whether or not the Timer0 interrupt is enabled. The T0IF bit can only be cleared in software. The Timer0 interrupt enable is the T0IE bit of the INTCON register. Note: The Timer0 interrupt cannot wake the processor from Sleep since the timer is frozen during Sleep. 8-BIT COUNTER MODE SYNCHRONIZATION
11.1.5
When in 8-Bit Counter mode, the incrementing edge on the T0CKI pin must be synchronized to the instruction clock. Synchronization can be accomplished by sampling the prescaler output on the Q2 and Q4 cycles of the instruction clock. The high and low periods of the external clocking source must meet the timing requirements as shown in Section 23.0 "Electrical Specifications".
DS41417A-page 100
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 11-1:
R/W-1 RBPU bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
OPTION_REG: OPTION REGISTER
R/W-1 R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0
INTEDG
RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual PORT latch values INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of INT pin 0 = Interrupt on falling edge of INT pin T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin or CPSOSC signal 0 = Internal instruction cycle clock (FOSC/4) T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module PS<2:0>: Prescaler Rate Select bits
BIT VALUE 000 001 010 011 100 101 110 111 TMR0 RATE 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 WDT RATE 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128
bit 6
bit 5
bit 4
bit 3
bit 2-0
TABLE 11-1:
Name CPSCON0 INTCON OPTION_REG TMR0 TRISA Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH TIMER0
Bit 7 CPSON GIE RBPU TRISA7 Bit 6 -- PEIE INTEDG TRISA6 Bit 5 -- T0IE T0CS TRISA5 Bit 4 -- INTE T0SE TRISA4 Bit 3 Bit 2 Bit 1 CPSOUT INTF PS1 TRISA1 Bit 0 T0XCS RBIF PS0 TRISA0 Value on POR, BOR 0--- 0000 0000 000x 1111 1111 xxxx xxxx TRISA3 TRISA2 1111 1111 Value on all other Resets 0--- 0000 0000 000x 1111 1111 uuuu uuuu 1111 1111
CPSRNG1 CPSRNG0 RBIE PSA T0IF PS2
Timer0 Module Register
- = Un implemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the Timer0 module.
2010 Microchip Technology Inc.
DS41417A-page 101
PIC16F/LF722A/723A
NOTES:
DS41417A-page 102
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
12.0 TIMER1 MODULE WITH GATE CONTROL
* * * * * Selectable Gate Source Polarity Gate Toggle Mode Gate Single-pulse Mode Gate Value Status Gate Event Interrupt
The Timer1 module is a 16-bit timer/counter with the following features: 16-bit timer/counter register pair (TMR1H:TMR1L) Programmable internal or external clock source 3-bit prescaler Dedicated LP oscillator circuit Synchronous or asynchronous operation Multiple Timer1 gate (count enable) sources Interrupt on overflow Wake-up on overflow (external clock, Asynchronous mode only) * Time base for the Capture/Compare function * Special Event Trigger (with CCP) * * * * * * * *
Figure 12-1 is a block diagram of the Timer1 module.
FIGURE 12-1:
T1GSS<1:0> T1G From Timer0 Overflow From Timer2 Match PR2 From WDT Overflow
TIMER1 BLOCK DIAGRAM
00 01 10 D 11
TMR1ON T1GPOL Set flag bit TMR1IF on Overflow T1GTM T1G_IN
T1GSPM 0 0 Single Pulse Data Bus
T1GVAL Q1
D EN
Q
Q
1
Acq. Control T1GGO/DONE
1
RD T1GCON
Set TMR1GIF
CK Q R
Interrupt det TMR1GE TMR1ON
TMR1(2) TMR1H TMR1L
EN Q D
T1CLK
0
Synchronized Clock Input
1
TMR1CS<1:0> T1OSO/T1CKI OUT T1OSC T1OSI EN 1 Cap. Sensing Oscillator T1SYNC
11 10
Prescaler 1, 2, 4, 8 2 T1CKPS<1:0> FOSC/2 Internal Clock
Synchronize(3) det
0
T1OSCEN
(1)
FOSC Internal Clock FOSC/4 Internal Clock
01
Sleep Input
00
T1CKI
Note 1: ST Buffer is high speed type when using T1CKI. 2: Timer1 register increments on rising edge. 3: Synchronize does not operate while in Sleep.
2010 Microchip Technology Inc.
DS41417A-page 103
PIC16F/LF722A/723A
12.1 Timer1 Operation 12.2 Clock Source Selection
The Timer1 module is a 16-bit incrementing counter which is accessed through the TMR1H:TMR1L register pair. Writes to TMR1H or TMR1L directly update the counter. When used with an internal clock source, the module is a timer and increments on every instruction cycle. When used with an external clock source, the module can be used as either a timer or counter and increments on every selected edge of the external source. Timer1 is enabled by configuring the TMR1ON and TMR1GE bits in the T1CON and T1GCON registers, respectively. Table 12-1 displays the Timer1 enable selections. The TMR1CS<1:0> and T1OSCEN bits of the T1CON register are used to select the clock source for Timer1. Table 12-2 displays the clock source selections.
12.2.1
INTERNAL CLOCK SOURCE
When the internal clock source is selected the TMR1H:TMR1L register pair will increment on multiples of FISC as determined by the Timer1 prescaler.
12.2.2
EXTERNAL CLOCK SOURCE
When the external clock source is selected, the Timer1 module may work as a timer or a counter. When enabled to count, Timer1 is increment ed on the rising edge of the external clock input T1CKI or the capacitive sensing oscillator signal. Either of these external clock sources can be synchronized to the microcontroller system clock or they can run asynchronously. When used as a timer with a clock oscillator, an external 32.768 kHz crystal can be used in conjunction with the dedicated internal oscillator circuit. Note: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge after any one or more of the following conditions: *Timer1 enabled after POR *Write to TMR1H or TMR1L *Timer1 is disabled *Timer1 is disabled (TMR1ON = 0) when T1CKI is high then Timer1 is enabled (TMR1ON=1) when T1CKI is low.
TABLE 12-1:
TMR1ON 0 0 1 1
TIMER1 ENABLE SELECTIONS
TMR1GE 0 1 0 1 Timer1 Operation Off Off Always On Count Enabled
TABLE 12-2:
TMR1CS1 0 0 1 1 1
CLOCK SOURCE SELECTIONS
TMR1CS0 1 0 1 0 0 T1OSCEN x x x 0 1 System Clock (FOSC) Instruction Clock (FOSC/4) Capacitive Sensing Oscillator External Clocking on T1CKI Pin Oscillator Circuit on T1OSI/T1OSO Pins Clock Source
DS41417A-page 104
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
12.3 Timer1 Prescaler
12.5.1
Timer1 has four prescaler options allowing 1, 2, 4 or 8 divisions of the clock input. The T1CKPS bits of the T1CON register control the prescale counter. The prescale counter is not directly readable or writable; however, the prescaler counter is cleared upon a write to TMR1H or TMR1L.
READING AND WRITING TIMER1 IN ASYNCHRONOUS COUNTER MODE
12.4
Timer1 Oscillator
Reading TMR1H or TMR1L while the timer is running from an external asynchronous clock will ensure a valid read (taken care of in hardware). However, the user should keep in mind that reading the 16-bit timer in two 8-bit values itself, poses certain problems, since the timer may overflow between the reads. For writes, it is recommended that the user simply stop the timer and write the desired values. A write contention may occur by writing to the timer registers, while the register is incrementing. This may produce an unpredictable value in the TMR1H:TMR1L register pair.
A dedicated low-power 32.768 kHz oscillator circuit is built-in between pins T1OSI (input) and T1OSO (amplifier output). This internal circuit is to be used in conjunction with an external 32.768 kHz crystal. The oscillator circuit is enabled by setting the T1OSCEN bit of the T1CON register. The oscillator will continue to run during Sleep. Note: The oscillator requires a start-up and stabilization time before use. Thus, T1OSCEN should be set and a suitable delay observed prior to enabling Timer1.
12.5
Timer1 Operation in Asynchronous Counter Mode
If control bit T1SYNC of the T1CON register is set, the external clock input is not synchronized. The timer increments asynchronously to the internal phase clocks. If external clock source is selected then the timer will continue to run during Sleep and can generate an interrupt on overflow, which will wake-up the processor. However, special precautions in software are needed to read/write the timer (see Section 12.5.1 "Reading and Writing Timer1 in Asynchronous Counter Mode"). Note: When switching from synchronous to asynchronous operation, it is possible to skip an increment. When switching from asynchronous to synchronous operation, it is possible to produce an additional increment.
2010 Microchip Technology Inc.
DS41417A-page 105
PIC16F/LF722A/723A
12.6 Timer1 Gate
12.6.2.1 T1G Pin Gate Operation
Timer1 can be configured to count freely or the count can be enabled and disabled using Timer1 gate circuitry. This is also referred to as Timer1 Gate Count Enable. Timer1 gate can also be driven by multiple selectable sources. The T1G pin is one source for Timer1 gate control. It can be used to supply an external source to the Timer1 gate circuitry.
12.6.2.2
Timer0 Overflow Gate Operation
12.6.1
TIMER1 GATE COUNT ENABLE
When Timer0 increments from FFh to 00h, a low-tohigh pulse will automatically be generated and internally supplied to the Timer1 gate circuitry.
The Timer1 gate is enabled by setting the TMR1GE bit of the T1GCON register. The polarity of the Timer1 gate is configured using the T1GPOL bit of the T1GCON register. When Timer1 Gate (T1G) input is active, Timer1 will increment on the rising edge of the Timer1 clock source. When Timer1 gate input is inactive, no incrementing will occur and Timer1 will hold the current count. See Figure 12-3 for timing details.
12.6.2.3
Timer2 Match Gate Operation
The TMR2 register will increment until it matches the value in the PR2 register. On the very next increment cycle, TMR2 will be reset to 00h. When this Reset occurs, a low-to-high pulse will automatically be generated and internally supplied to the Timer1 gate circuitry.
12.6.2.4
Watchdog Overflow Gate Operation
TABLE 12-3:
T1CLK
TIMER1 GATE ENABLE SELECTIONS
T1G 0 1 0 1 Timer1 Operation Counts Holds Count Holds Count Counts 0 0 1 1
T1GPOL
The Watchdog Timer oscillator, prescaler and counter will be automatically turned on when TMR1GE = 1 and T1GSS selects the WDT as a gate source for Timer1 (T1GSS = 11). TMR1ON does not factor into the oscillator, prescaler and counter enable. See Table 12-5. The PSA and PS bits of the OPTION register still control what time-out interval is selected. Changing the prescaler during operation may result in a spurious capture. Enabling the Watchdog Timer oscillator does not automatically enable a Watchdog Reset or Wake-up from Sleep upon counter overflow. Note: When using the WDT as a gate source for Timer1, operations that clear the Watchdog Timer (CLRWDT, SLEEP instructions) will affect the time interval being measured for capacitive sensing. This includes waking from Sleep. All other interrupts that might wake the device from Sleep should be disabled to prevent them from disturbing the measurement period.
12.6.2
TIMER1 GATE SOURCE SELECTION
The Timer1 gate source can be selected from one of four different sources. Source selection is controlled by the T1GSS bits of the T1GCON register. The polarity for each available source is also selectable. Polarity selection is controlled by the T1GPOL bit of the T1GCON register.
TABLE 12-4:
T1GSS 00 01 10 11
TIMER1 GATE SOURCES
Timer1 Gate Source
Timer1 Gate Pin Overflow of Timer0 (TMR0 increments from FFh to 00h) Timer2 match PR2 (TMR2 increments to match PR2) Count Enabled by WDT Overflow (Watchdog Time-out interval expired)
As the gate signal coming from the WDT counter will generate different pulse widths depending on if the WDT is enabled, when the CLRWDT instruction is executed, and so on, Toggle mode must be used. A specific sequence is required to put the device into the correct state to capture the next WDT counter interval.
DS41417A-page 106
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 12-5:
WDTE 1 1 0 0
WDT/TIMER1 GATE INTERACTION
TMR1GE = 1 and T1GSS = 11
N Y Y N
WDT Oscillator Enable Y Y Y N
WDT Reset Y Y N N
Wake-up Y Y N N
WDT Available for T1G Source N Y Y N
12.6.3
TIMER1 GATE TOGGLE MODE
12.6.4
When Timer1 Gate Toggle mode is enabled, it is possible to measure the full-cycle length of a Timer1 gate signal, as opposed to the duration of a single level pulse. The Timer1 gate source is routed through a flip-flop that changes state on every incrementing edge of the signal. See Figure 12-4 for timing details. Timer1 Gate Toggle mode is enabled by setting the T1GTM bit of the T1GCON register. When the T1GTM bit is cleared, the flip-flop is cleared and held clear. This is necessary in order to control which edge is measured. Note: Enabling Toggle mode at the same time as changing the gate polarity may result in indeterminate operation.
TIMER1 GATE SINGLE-PULSE MODE
When Timer1 Gate Single-Pulse mode is enabled, it is possible to capture a single pulse gate event. Timer1 Gate Single-Pulse mode is first enabled by setting the T1GSPM bit in the T1GCON register. Next, the T1GGO/DONE bit in the T1GCON register must be set. The Timer1 will be fully enabled on the next incrementing edge. On the next trailing edge of the pulse, the T1GGO/DONE bit will automatically be cleared. No other gate events will be allowed to increment Timer1 until the T1GGO/DONE bit is once again set in software. Clearing the T1GSPM bit of the T1GCON register will also clear the T1GGO/DONE bit. See Figure 12-5 for timing details. Enabling the Toggle mode and the Single-Pulse mode simultaneously will permit both sections to work together. This allows the cycle times on the Timer1 gate source to be measured. See Figure 12-6 for timing details.
12.6.5
TIMER1 GATE VALUE STATUS
When Timer1 gate value status is utilized, it is possible to read the most current level of the gate control value. The value is stored in the T1GVAL bit in the T1GCON register. The T1GVAL bit is valid even when the Timer1 gate is not enabled (TMR1GE bit is cleared).
12.6.6
TIMER1 GATE EVENT INTERRUPT
When Timer1 gate event interrupt is enabled, it is possible to generate an interrupt upon the completion of a gate event. When the falling edge of T1GVAL occurs, the TMR1GIF flag bit in the PIR1 register will be set. If the TMR1GIE bit in the PIE1 register is set, then an interrupt will be recognized. The TMR1GIF flag bit operates even when the Timer1 gate is not enabled (TMR1GE bit is cleared).
2010 Microchip Technology Inc.
DS41417A-page 107
PIC16F/LF722A/723A
12.7 Timer1 Interrupt 12.9 CCP Capture/Compare Time Base
The Timer1 register pair (TMR1H:TMR1L) increments to FFFFh and rolls over to 0000h. When Timer1 rolls over, the Timer1 interrupt flag bit of the PIR1 register is set. To enable the interrupt on rollover, you must set these bits: * * * * TMR1ON bit of the T1CON register TMR1IE bit of the PIE1 register PEIE bit of the INTCON register GIE bit of the INTCON register The CCP module uses the TMR1H:TMR1L register pair as the time base when operating in Capture or Compare mode. In Capture mode, the value in the TMR1H:TMR1L register pair is copied into the CCPR1H:CCPR1L register pair on a configured event. In Compare mode, an event is triggered when the value CCPR1H:CCPR1L register pair matches the value in the TMR1H:TMR1L register pair. This event can be a Special Event Trigger. For more information, see Section 15.0 "Capture/ Compare/PWM (CCP) Module".
The interrupt is cleared by clearing the TMR1IF bit in the Interrupt Service Routine. Note: The TMR1H:TMR1L register pair and the TMR1IF bit should be cleared before enabling interrupts.
12.10 CCP Special Event Trigger
When the CCP is configured to trigger a special event, the trigger will clear the TMR1H:TMR1L register pair. This special event does not cause a Timer1 interrupt. The CCP module may still be configured to generate a CCP interrupt. In this mode of operation, the CCPR1H:CCPR1L register pair becomes the period register for Timer1. Timer1 should be synchronized to the FOSC/4 to utilize the Special Event Trigger. Asynchronous operation of Timer1 can cause a Special Event Trigger to be missed. In the event that a write to TMR1H or TMR1L coincides with a Special Event Trigger from the CCP, the write will take precedence. For more information, see Section 9.2.5 "Special Event Trigger".
12.8
Timer1 Operation During Sleep
Timer1 can only operate during Sleep when setup in Asynchronous Counter mode. In this mode, an external crystal or clock source can be used to increment the counter. To set up the timer to wake the device: * * * * * TMR1ON bit of the T1CON register must be set TMR1IE bit of the PIE1 register must be set PEIE bit of the INTCON register must be set T1SYNC bit of the T1CON register must be set TMR1CS bits of the T1CON register must be configured * T1OSCEN bit of the T1CON register must be configured * TMR1GIE bit of the T1GCON register must be configured The device will wake-up on an overflow and execute the next instructions. If the GIE bit of the INTCON register is set, the device will call the Interrupt Service Routine (0004h).
FIGURE 12-2:
T1CKI = 1 when TMR1 Enabled
TIMER1 INCREMENTING EDGE
T1CKI = 0 when TMR1 Enabled Note 1: 2: Arrows indicate counter increments. In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock.
DS41417A-page 108
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 12-3: TIMER1 GATE COUNT ENABLE MODE
TMR1GE T1GPOL T1G_IN
T1CKI
T1GVAL
TIMER1
N
N+1
N+2
N+3
N+4
FIGURE 12-4:
TIMER1 GATE TOGGLE MODE
TMR1GE T1GPOL T1GTM T1G_IN T1CKI
T1GVAL TIMER1 N
N+1 N+2 N+3
N+4
N+5 N+6 N+7 N+8
2010 Microchip Technology Inc.
DS41417A-page 109
PIC16F/LF722A/723A
FIGURE 12-5: TIMER1 GATE SINGLE-PULSE MODE
TMR1GE T1GPOL T1GSPM T1GGO/ DONE T1G_IN Set by software Counting enabled on rising edge of T1G Cleared by hardware on falling edge of T1GVAL
T1CKI
T1GVAL
TIMER1
N
N+1
N+2 Set by hardware on falling edge of T1GVAL Cleared by software
TMR1GIF
Cleared by software
DS41417A-page 110
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 12-6:
TMR1GE T1GPOL T1GSPM T1GTM T1GGO/ DONE T1G_IN Set by software Counting enabled on rising edge of T1G Cleared by hardware on falling edge of T1GVAL
TIMER1 GATE SINGLE-PULSE AND TOGGLE COMBINED MODE
T1CKI
T1GVAL
TIMER1
N
N+1
N+2
N+3
N+4 Cleared by software
TMR1GIF
Cleared by software
Set by hardware on falling edge of T1GVAL
2010 Microchip Technology Inc.
DS41417A-page 111
PIC16F/LF722A/723A
12.11 Timer1 Control Register
The Timer1 Control register (T1CON), shown in Register 12-1, is used to control Timer1 and select the various features of the Timer1 module.
REGISTER 12-1:
R/W-0 TMR1CS1 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6
T1CON: TIMER1 CONTROL REGISTER
R/W-0 R/W-0 T1CKPS1 R/W-0 T1CKPS0 R/W-0 T1OSCEN R/W-0 T1SYNC U-0 -- R/W-0 TMR1ON bit 0
TMR1CS0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TMR1CS<1:0>: Timer1 Clock Source Select bits 11 = Timer1 clock source is Capacitive Sensing Oscillator (CAPOSC) 10 = Timer1 clock source is pin or oscillator: If T1OSCEN = 0: External clock from T1CKI pin (on the rising edge) If T1OSCEN = 1: Crystal oscillator on T1OSI/T1OSO pins 01 = Timer1 clock source is system clock (FOSC) 00 = Timer1 clock source is instruction clock (FOSC/4) T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value T1OSCEN: LP Oscillator Enable Control bit 1 = Dedicated Timer1 oscillator circuit enabled 0 = Dedicated Timer1 oscillator circuit disabled T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS<1:0> = 1X 1 = Do not synchronize external clock input 0 = Synchronize external clock input with system clock (FOSC) TMR1CS<1:0> = 0X This bit is ignored. Timer1 uses the internal clock when TMR1CS<1:0> = 1X.
bit 5-4
bit 3
bit 2
bit 1 bit 0
Unimplemented: Read as `0' TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 Clears Timer1 gate flip-flop
DS41417A-page 112
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
12.12 Timer1 Gate Control Register
The Timer1 Gate Control register (T1GCON), shown in Register 12-2, is used to control Timer1 gate.
REGISTER 12-2:
R/W-0 TMR1GE bit 7 Legend: R = Readable bit -n = Value at POR bit 7
T1GCON: TIMER1 GATE CONTROL REGISTER
R/W-0 R/W-0 T1GTM R/W-0 T1GSPM R/W-0 T1GGO/ DONE R-x T1GVAL R/W-0 T1GSS1 R/W-0 T1GSS0 bit 0
T1GPOL
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TMR1GE: Timer1 Gate Enable bit If TMR1ON = 0: This bit is ignored If TMR1ON = 1: 1 = Timer1 counting is controlled by the Timer1 gate function 0 = Timer1 counts regardless of Timer1 gate function T1GPOL: Timer1 Gate Polarity bit 1 = Timer1 gate is active-high (Timer1 counts when gate is high) 0 = Timer1 gate is active-low (Timer1 counts when gate is low) T1GTM: Timer1 Gate Toggle Mode bit 1 = Timer1 Gate Toggle mode is enabled. 0 = Timer1 Gate Toggle mode is disabled and toggle flip flop is cleared Timer1 gate flip-flop toggles on every rising edge. T1GSPM: Timer1 Gate Single Pulse Mode bit 1 = Timer1 Gate Single-Pulse mode is enabled and is controlling Timer1 gate 0 = Timer1 Gate Single-Pulse mode is disabled T1GGO/DONE: Timer1 Gate Single-Pulse Acquisition Status bit 1 = Timer1 gate single-pulse acquisition is ready, waiting for an edge 0 = Timer1 gate single-pulse acquisition has completed or has not been started This bit is automatically cleared when T1GSPM is cleared. T1GVAL: Timer1 Gate Current State bit Indicates the current state of the Timer1 gate that could be provided to TMR1H:TMR1L. Unaffected by Timer1 Gate Enable (TMR1GE). T1GSS<1:0>: Timer1 Gate Source Select bits 00 = Timer1 gate pin 01 = Timer0 Overflow output 10 = TMR2 Match PR2 output 11 = Watchdog Timer scaler overflow Watchdog Timer oscillator is turned on if TMR1GE = 1, regardless of the state of TMR1ON
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1-0
2010 Microchip Technology Inc.
DS41417A-page 113
PIC16F/LF722A/723A
TABLE 12-6:
Name ANSELB CCP1CON CCP2CON INTCON PIE1 PIR1 PORTB TMR1H TMR1L TRISB TRISC T1CON T1GCON Legend: Bit 7 -- -- -- GIE TMR1GIE TMR1GIF RB7
SUMMARY OF REGISTERS ASSOCIATED WITH TIMER1
Bit 6 -- -- -- PEIE ADIE ADIF RB6 Bit 5 ANSB5 DC1B1 DC2B1 T0IE RCIE RCIF RB5 Bit 4 ANSB4 DC1B0 DC2B0 INTE TXIE TXIF RB4 Bit 3 ANSB3 CCP1M3 CCP2M3 RBIE SSPIE SSPIF RB3 Bit 2 ANSB2 CCP1M2 CCP2M2 T0IF CCP1IE CCP1IF RB2 Bit 1 ANSB1 CCP1M1 CCP2M1 INTF TMR2IE TMR2IF RB1 Bit 0 ANSB0 CCP1M0 CCP2M0 RBIF TMR1IE TMR1IF RB0 Value on POR, BOR --11 1111 --00 0000 --00 0000 0000 000x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx xxxx xxxx TRISB1 TRISC1 -- T1GSS1 TRISB0 TRISC0 TMR1ON T1GSS0 1111 1111 1111 1111 0000 00-0 0000 0x00 Value on all other Resets --11 1111 --00 0000 --00 0000 0000 000x 0000 0000 0000 0000 xxxx xxxx uuuu uuuu uuuu uuuu 1111 1111 1111 1111 uuuu uu-u uuuu uxuu
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register Holding Register for the Least Significant Byte of the 16-bit TMR1 Register TRISB7 TRISC7 TRISB6 TRISC6 TRISB5 TRISC5 T1CKPS1 T1GTM TRISB4 TRISC4 T1CKPS0 T1GSPM TRISB3 TRISC3 T1OSCEN T1GGO/ DONE TRISB2 TRISC2 T1SYNC T1GVAL
TMR1CS1 TMR1CS0 TMR1GE T1GPOL
x = unknown, u = unchanged, -- = unimplemented, read as `0'. Shaded cells are not used by the Timer1 module.
DS41417A-page 114
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
13.0 TIMER2 MODULE
The Timer2 module is an 8-bit timer with the following features: * * * * * 8-bit timer register (TMR2) 8-bit period register (PR2) Interrupt on TMR2 match with PR2 Software programmable prescaler (1:1, 1:4, 1:16) Software programmable postscaler (1:1 to 1:16) The TMR2 and PR2 registers are both fully readable and writable. On any Reset, the TMR2 register is set to 00h and the PR2 register is set to FFh. Timer2 is turned on by setting the TMR2ON bit in the T2CON register to a `1'. Timer2 is turned off by clearing the TMR2ON bit to a `0'. The Timer2 prescaler is controlled by the T2CKPS bits in the T2CON register. The Timer2 postscaler is controlled by the TOUTPS bits in the T2CON register. The prescaler and postscaler counters are cleared when: * A write to TMR2 occurs. * A write to T2CON occurs. * Any device Reset occurs (Power-on Reset, MCLR Reset, Watchdog Timer Reset, or Brown-out Reset). Note: TMR2 is not cleared when T2CON is written.
See Figure 13-1 for a block diagram of Timer2.
13.1
Timer2 Operation
The clock input to the Timer2 module is the system instruction clock (FOSC/4). The clock is fed into the Timer2 prescaler, which has prescale options of 1:1, 1:4 or 1:16. The output of the prescaler is then used to increment the TMR2 register. The values of TMR2 and PR2 are constantly compared to determine when they match. TMR2 will increment from 00h until it matches the value in PR2. When a match occurs, two things happen: * TMR2 is reset to 00h on the next increment cycle. * The Timer2 postscaler is incremented. The match output of the Timer2/PR2 comparator is then fed into the Timer2 postscaler. The postscaler has postscale options of 1:1 to 1:16 inclusive. The output of the Timer2 postscaler is used to set the TMR2IF interrupt flag bit in the PIR1 register.
FIGURE 13-1:
TIMER2 BLOCK DIAGRAM
TMR2 Output Sets Flag bit TMR2IF
FOSC/4
Prescaler 1:1, 1:4, 1:16 2 T2CKPS<1:0>
TMR2 Comparator
Reset Postscaler 1:1 to 1:16 4 TOUTPS<3:0>
EQ
PR2
2010 Microchip Technology Inc.
DS41417A-page 115
PIC16F/LF722A/723A
REGISTER 13-1:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7 bit 6-3 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
T2CON: TIMER2 CONTROL REGISTER
R/W-0 R/W-0 TOUTPS2 R/W-0 TOUTPS1 R/W-0 TOUTPS0 R/W-0 TMR2ON R/W-0 T2CKPS1 R/W-0 T2CKPS0 bit 0
TOUTPS3
Unimplemented: Read as `0' TOUTPS<3:0>: Timer2 Output Postscaler Select bits 0000 = 1:1 Postscaler 0001 = 1:2 Postscaler 0010 = 1:3 Postscaler 0011 = 1:4 Postscaler 0100 = 1:5 Postscaler 0101 = 1:6 Postscaler 0110 = 1:7 Postscaler 0111 = 1:8 Postscaler 1000 = 1:9 Postscaler 1001 = 1:10 Postscaler 1010 = 1:11 Postscaler 1011 = 1:12 Postscaler 1100 = 1:13 Postscaler 1101 = 1:14 Postscaler 1110 = 1:15 Postscaler 1111 = 1:16 Postscaler TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off T2CKPS<1:0>: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16
bit 2
bit 1-0
TABLE 13-1:
Name INTCON PIE1 PIR1 PR2 TMR2 T2CON Legend: Bit 7 GIE TMR1GIE TMR1GIF
SUMMARY OF REGISTERS ASSOCIATED WITH TIMER2
Bit 6 PEIE ADIE ADIF Bit 5 T0IE RCIE RCIF Bit 4 INTE TXIE TXIF Bit 3 RBIE SSPIE SSPIF Bit 2 T0IF CCP1IE CCP1IF Bit 1 INTF TMR2IE TMR2IF Bit 0 RBIF TMR1IE TMR1IF Value on POR, BOR 0000 000x 0000 0000 0000 0000 1111 1111 0000 0000 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 TOUTPS1 Value on all other Resets 0000 000x 0000 0000 0000 0000 1111 1111 0000 0000 -000 0000
Timer2 Module Period Register Holding Register for the 8-bit TMR2 Register -- TOUTPS3 TOUTPS2
x = unknown, u = unchanged, - = unimplemented read as `0'. Shaded cells are not used for Timer2 module.
DS41417A-page 116
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
14.0 CAPACITIVE SENSING MODULE
sensing module. The capacitive sensing module requires software and at least one timer resource to determine the change in frequency. Key features of this module include: * * * * * Analog MUX for monitoring multiple inputs Capacitive sensing oscillator Multiple timer resources Software control Operation during Sleep
The capacitive sensing module allows for an interaction with an end user without a mechanical interface. In a typical application, the capacitive sensing module is attached to a pad on a printed circuit board (PCB), which is electrically isolated from the end user. When the end user places their finger over the PCB pad, a capacitive load is added, causing a frequency shift in the capacitive
FIGURE 14-1:
CAPACITIVE SENSING BLOCK DIAGRAM
Timer0 Module T0CS FOSC/4 0 1 0 1 TMR0 Overflow Set T0IF
T0XCS T0CKI
CPSCH<2:0> CPSON(1)
Timer1 Module CPS0 CPS1 CPS2 CPS3 CPS4 CPS5 CPS6 CPS7 Capacitive Sensing Oscillator CPSOSC CPSON T1CS<1:0> FOSC CPSCLK CPSOUT FOSC/4 T1OSC/ T1CKI T1GSEL<1:0> T1G Timer1 Gate Control Logic EN TMR1H:TMR1L
CPSRNG<1:0>
Watchdog Timer Module
WDT Event TMR2
Timer2 Module Overflow Postscaler Set TMR2IF
LP WDT OSC PS<2:0>
WDT Overflow Scaler
Note 1:
If CPSON = 0, disabling capacitive sensing, no channel is selected.
2010 Microchip Technology Inc.
DS41417A-page 117
PIC16F/LF722A/723A
14.1 Analog MUX
14.4.1 TIMER0
The capacitive sensing module can monitor up to 16 inputs. The capacitive sensing inputs are defined as CPS<15:0>. To determine if a frequency change has occurred the user must: * Select the appropriate CPS pin by setting the CPSCH<3:0> bits of the CPSCON1 register * Set the corresponding ANSEL bit * Set the corresponding TRIS bit * Run the software algorithm Selection of the CPSx pin while the module is enabled will cause the capacitive sensing oscillator to be on the CPSx pin. Failure to set the corresponding ANSEL and TRIS bits can cause the capacitive sensing oscillator to stop, leading to false frequency readings. To select Timer0 as the timer resource for the capacitive sensing module: * Set the T0XCS bit of the CPSCON0 register * Clear the T0CS bit of the OPTION register When Timer0 is chosen as the timer resource, the capacitive sensing oscillator will be the clock source for Timer0. Refer to Section 11.0 "Timer0 Module" for additional information.
14.4.2
TIMER1
14.2
Capacitive Sensing Oscillator
The capacitive sensing oscillator consists of a constant current source and a constant current sink, to produce a triangle waveform. The CPSOUT bit of the CPSCON0 register shows the status of the capacitive sensing oscillator, whether it is a sinking or sourcing current. The oscillator is designed to drive a capacitive load (single PCB pad) and at the same time, be a clock source to either Timer0 or Timer1. The oscillator has three different current settings as defined by CPSRNG<1:0> of the CPSCON0 register. The different current settings for the oscillator serve two purposes: * Maximize the number of counts in a timer for a fixed time base * Maximize the count differential in the timer during a change in frequency
To select Timer1 as the timer resource for the capacitive sensing module, set the TMR1CS<1:0> of the T1CON register to `11'. When Timer1 is chosen as the timer resource, the capacitive sensing oscillator will be the clock source for Timer1. Because the Timer1 module has a gate control, developing a time base for the frequency measurement can be simplified using either: * The Timer0 overflow flag * The Timer2 overflow flag * The WDT overflow flag It is recommended that one of these flags, in conjunction with the toggle mode of the Timer1 gate, is used to develop the fixed time base required by the software portion of the capacitive sensing module. Refer to Section 12.0 "Timer1 Module with Gate Control" for additional information.
TABLE 14-1:
TMR1ON 0 0 1 1
TIMER1 ENABLE FUNCTION
TMR1GE 0 1 0 1 Timer1 Operation Off Off On Count Enabled by input
14.3
Timer Resources
To measure the change in frequency of the capacitive sensing oscillator, a fixed time base is required. For the period of the fixed time base, the capacitive sensing oscillator is used to clock either Timer0 or Timer1. The frequency of the capacitive sensing oscillator is equal to the number of counts in the timer divided by the period of the fixed time base.
14.4
Fixed Time Base
To measure the frequency of the capacitive sensing oscillator, a fixed time base is required. Any timer resource or software loop can be used to establish the fixed time base. It is up to the end user to determine the method in which the fixed time base is generated. Note: The fixed time base can not be generated by the timer resource the capacitive sensing oscillator is clocking.
DS41417A-page 118
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
14.5 Software Control
14.5.3 FREQUENCY THRESHOLD
The software portion of the capacitive sensing module is required to determine the change in frequency of the capacitive sensing oscillator. This is accomplished by the following: * Setting a fixed time base to acquire counts on Timer0 or Timer1 * Establishing the nominal frequency for the capacitive sensing oscillator * Establishing the reduced frequency for the capacitive sensing oscillator due to an additional capacitive load * Set the frequency threshold The frequency threshold should be placed midway between the value of nominal frequency and the reduced frequency of the capacitive sensing oscillator. Refer to Application Note AN1103, "Software Handling for Capacitive Sensing" (DS01103) for more detailed information the software required for capacitive sensing module. Note: For more information on general capacitive sensing refer to Application Notes: *AN1101, "Introduction to Capacitive Sensing" (DS01101) *AN1102, "Layout and Physical Design Guidelines for Capacitive Sensing" (DS01102)
14.5.1
NOMINAL FREQUENCY (NO CAPACITIVE LOAD)
To determine the nominal frequency of the capacitive sensing oscillator: * Remove any extra capacitive load on the selected CPSx pin * At the start of the fixed time base, clear the timer resource * At the end of the fixed time base save the value in the timer resource The value of the timer resource is the number of oscillations of the capacitive sensing oscillator for the given time base. The frequency of the capacitive sensing oscillator is equal to the number of counts on in the timer divided by the period of the fixed time base.
14.5.2
REDUCED FREQUENCY (ADDITIONAL CAPACITIVE LOAD)
The extra capacitive load will cause the frequency of the capacitive sensing oscillator to decrease. To determine the reduced frequency of the capacitive sensing oscillator: * Add a typical capacitive load on the selected CPSx pin * Use the same fixed time base as the nominal frequency measurement * At the start of the fixed time base, clear the timer resource * At the end of the fixed time base save the value in the timer resource The value of the timer resource is the number of oscillations of the capacitive sensing oscillator with an additional capacitive load. The frequency of the capacitive sensing oscillator is equal to the number of counts on in the timer divided by the period of the fixed time base. This frequency should be less than the value obtained during the nominal frequency measurement.
2010 Microchip Technology Inc.
DS41417A-page 119
PIC16F/LF722A/723A
14.6 Operation During Sleep
The capacitive sensing oscillator will continue to run as long as the module is enabled, independent of the part being in Sleep. In order for the software to determine if a frequency change has occurred, the part must be awake. However, the part does not have to be awake when the timer resource is acquiring counts. One way to acquire the Timer1 counts while in Sleep is to have Timer1 gated with the overflow of the Watchdog Timer. This can be accomplished using the following steps: 1. 2. 3. 4. 5. 6. 7. 8. Configure the Watchdog Time-out overflow as the Timer1's gate source T1GSS<1:0> = 11. Set Timer1 gate to toggle mode by setting the T1GTM bit of the T1GCON register. Set the TMR1GE bit of the T1GCON register. Set TMR1ON bit of the T1CON register. Enable capacitive sensing module with the appropriate current settings and pin selection. Clear Timer1. Put the part to Sleep. On the first WDT overflow, the capacitive sensing oscillator will begin to increment Timer1. Then put the part to Sleep. On the second WDT overflow Timer1 will stop incrementing. Then run the software routine to determine if a frequency change has occurred.
9.
Refer to Section 12.0 "Timer1 Module with Gate Control" for additional information. Note 1: When using the WDT to set the interval on Timer1, any other source that wakes the part up early will cause the WDT overflow to be delayed, affecting the value captured by Timer1. 2: Timer0 does not operate when in Sleep, and therefore cannot be used for capacitive sense measurements in Sleep.
DS41417A-page 120
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 14-1:
R/W-0 CPSON bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
CPSCON0: CAPACITIVE SENSING CONTROL REGISTER 0
U-0 -- U-0 -- U-0 -- R/W-0 CPSRNG1 R/W-0 CPSRNG0 R-0 CPSOUT R/W-0 T0XCS bit 0
CPSON: Capacitive Sensing Module Enable bit 1 = Capacitive sensing module is operating 0 = Capacitive sensing module is shut off and consumes no operating current Unimplemented: Read as `0' CPSRNG<1:0>: Capacitive Sensing Oscillator Range bits 00 = Oscillator is off. 01 = Oscillator is in low range. Charge/discharge current is nominally 0.1 A. 10 = Oscillator is in medium range. Charge/discharge current is nominally 1.2 A. 11 = Oscillator is in high range. Charge/discharge current is nominally 18 A. CPSOUT: Capacitive Sensing Oscillator Status bit 1 = Oscillator is sourcing current (Current flowing out the pin) 0 = Oscillator is sinking current (Current flowing into the pin) T0XCS: Timer0 External Clock Source Select bit If T0CS = 1 The T0XCS bit controls which clock external to the core/Timer0 module supplies Timer0: 1 = Timer0 Clock Source is the capacitive sensing oscillator 0 = Timer0 Clock Source is the T0CKI pin If T0CS = 0 Timer0 clock source is controlled by the core/Timer0 module and is FOSC/4.
bit 6-4 bit 3-2
bit 1
bit 0
2010 Microchip Technology Inc.
DS41417A-page 121
PIC16F/LF722A/723A
REGISTER 14-2:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-3 bit 2-0 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
CPSCON1: CAPACITIVE SENSING CONTROL REGISTER 1
U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 CPSCH2 R/W-0 CPSCH1 R/W-0 CPSCH0 bit 0
Unimplemented: Read as `0' CPSCH<2:0>: Capacitive Sensing Channel Select bits If CPSON = 0: These bits are ignored. No channel is selected. If CPSON = 1: 0000 = channel 0, (CPS0) 0001 = channel 1, (CPS1) 0010 = channel 2, (CPS2) 0011 = channel 3, (CPS3) 0100 = channel 4, (CPS4) 0101 = channel 5, (CPS5) 0110 = channel 6, (CPS6) 0111 = channel 7, (CPS7)
TABLE 14-2:
Name ANSELA ANSELB OPTION_REG PIE1 PIR1 T1CON T2CON TRISA TRISB Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH CAPACITIVE SENSING
Bit 7 -- -- RBPU Bit 6 -- -- INTEDG ADIE ADIF TMR1CS0 TOUTPS3 TRISA6 TRISB6 Bit 5 ANSA5 ANSB5 T0CS RCIE RCIF T1CKPS1 TOUTPS2 TRISA5 TRISB5 Bit 4 ANSA4 ANSB4 T0SE TXIE TXIF T1CKPS0 TOUTPS1 TRISA4 TRISB4 Bit 3 ANSA3 ANSB3 PSA SSPIE SSPIF T1OSCEN TOUTPS0 TRISA3 TRISB3 Bit 2 ANSA2 ANSB2 PS2 CCP1IE CCP1IF T1SYNC TMR2ON TRISA2 TRISB2 Bit 1 ANSA1 ANSB1 PS1 TMR2IE TMR2IF -- T2CKPS1 TRISA1 TRISB1 Bit 0 ANSA0 ANSB0 PS0 TMR1IE TMR1IF TMR1ON T2CKPS0 TRISA0 TRISB0 Value on POR, BOR --11 1111 --11 1111 1111 1111 0000 0000 0000 0000 0000 00-0 -000 0000 1111 1111 1111 1111 Value on all other Resets --11 1111 --11 1111 1111 1111 0000 0000 0000 0000 0000 00-0 -000 0000 1111 1111 1111 1111
TMR1GIE TMR1GIF TMR1CS1 -- TRISA7 TRISB7
- = Unimplemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the capacitive sensing module.
DS41417A-page 122
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
15.0 CAPTURE/COMPARE/PWM (CCP) MODULE
TABLE 15-1: CCP MODE - TIMER RESOURCES REQUIRED
Timer Resource Timer1 Timer1 Timer2 CCP Mode Capture Compare PWM
The Capture/Compare/PWM module is a peripheral which allows the user to time and control different events. In Capture mode, the peripheral allows the timing of the duration of an event. The Compare mode allows the user to trigger an external event when a predetermined amount of time has expired. The PWM mode can generate a Pulse-Width Modulated signal of varying frequency and duty cycle. The timer resources used by the module are shown in Table 15-1. Additional information on CCP modules is available in the Application Note AN594, "Using the CCP Modules" (DS00594).
TABLE 15-2:
CCP1 Mode Capture Capture Compare PWM PWM PWM Note 1: 2:
INTERACTION OF TWO CCP MODULES
CCP2 Mode Capture Compare Compare PWM Capture Compare Same TMR1 time base Same TMR1 time base(1, 2) Same TMR1 time base(1, 2) The PWMs will have the same frequency and update rate (TMR2 interrupt). The rising edges will be aligned. None None Interaction
If CCP2 is configured as a Special Event Trigger, CCP1 will clear Timer1, affecting the value captured on the CCP2 pin. If CCP1 is in Capture mode and CCP2 is configured as a Special Event Trigger, CCP2 will clear Timer1, affecting the value captured on the CCP1 pin.
Note:
CCPRx and CCPx throughout this document refer to CCPR1 or CCPR2 and CCP1 or CCP2, respectively.
2010 Microchip Technology Inc.
DS41417A-page 123
PIC16F/LF722A/723A
REGISTER 15-1:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-4 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
CCPxCON: CCPx CONTROL REGISTER
U-0 -- R/W-0 DCxB1 R/W-0 DCxB0 R/W-0 CCPxM3 R/W-0 CCPxM2 R/W-0 CCPxM1 R/W-0 CCPxM0 bit 0
Unimplemented: Read as `0' DCxB<1:0>: PWM Duty Cycle Least Significant bits Capture mode: Unused Compare mode: Unused PWM mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL. CCPxM<3:0>: CCP Mode Select bits 0000 = Capture/Compare/PWM off (resets CCP module) 0001 = Unused (reserved) 0010 = Compare mode, toggle output on match (CCPxIF bit of the PIRx register is set) 0011 = Unused (reserved) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (CCPxIF bit of the PIRx register is set) 1001 = Compare mode, clear output on match (CCPxIF bit of the PIRx register is set) 1010 = Compare mode, generate software interrupt on match (CCPxIF bit is set of the PIRx register, CCPx pin is unaffected) 1011 = Compare mode, trigger special event (CCPxIF bit of the PIRx register is set, TMR1 is reset and A/D conversion(1) is started if the ADC module is enabled. CCPx pin is unaffected.) 11xx = PWM mode.
bit 3-0
Note 1: A/D conversion start feature is available only on CCP2.
DS41417A-page 124
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
15.1 Capture Mode
15.1.3 SOFTWARE INTERRUPT
In Capture mode, CCPRxH:CCPRxL captures the 16-bit value of the TMR1 register when an event occurs on pin CCPx. An event is defined as one of the following and is configured by the CCPxM<3:0> bits of the CCPxCON register: * * * * Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCPxIE interrupt enable bit of the PIEx register clear to avoid false interrupts. Additionally, the user should clear the CCPxIF interrupt flag bit of the PIRx register following any change in operating mode. Note: Clocking Timer1 from the system clock (FOSC) should not be used in Capture mode. In order for Capture mode to recognize the trigger event on the CCPx pin, Timer1 must be clocked from the instruction clock (FOSC/4) or from an external clock source.
When a capture is made, the Interrupt Request Flag bit CCPxIF of the PIRx register is set. The interrupt flag must be cleared in software. If another capture occurs before the value in the CCPRxH, CCPRxL register pair is read, the old captured value is overwritten by the new captured value (refer to Figure 15-1).
15.1.4
CCP PRESCALER
15.1.1
CCPx PIN CONFIGURATION
In Capture mode, the CCPx pin should be configured as an input by setting the associated TRIS control bit. Either RC1 or RB3 can be selected as the CCP2 pin. Refer to Section 6.1 "Alternate Pin Function" for more information. Note: If the CCPx pin is configured as an output, a write to the port can cause a capture condition.
There are four prescaler settings specified by the CCPxM<3:0> bits of the CCPxCON register. Whenever the CCP module is turned off, or the CCP module is not in Capture mode, the prescaler counter is cleared. Any Reset will clear the prescaler counter. Switching from one capture prescaler to another does not clear the prescaler and may generate a false interrupt. To avoid this unexpected operation, turn the module off by clearing the CCPxCON register before changing the prescaler (refer to Example 15-1).
EXAMPLE 15-1:
BANKSEL CCP1CON CLRF MOVLW
FIGURE 15-1:
CAPTURE MODE OPERATION BLOCK DIAGRAM
Set Flag bit CCPxIF (PIRx register)
CHANGING BETWEEN CAPTURE PRESCALERS
Prescaler 1, 4, 16 CCPx
CCPRxH and Edge Detect Capture Enable TMR1H
CCPRxL
MOVWF
;Set Bank bits to point ;to CCP1CON CCP1CON ;Turn CCP module off NEW_CAPT_PS ;Load the W reg with ; the new prescaler ; move value and CCP ON CCP1CON ;Load CCP1CON with this ; value
15.1.5
TMR1L
CAPTURE DURING SLEEP
CCPxCON<3:0> System Clock (FOSC)
15.1.2
TIMER1 MODE SELECTION
Capture mode depends upon the Timer1 module for proper operation. There are two options for driving the Timer1 module in Capture mode. It can be driven by the instruction clock (FOSC/4), or by an external clock source. If Timer1 is clocked by FOSC/4, then Timer1 will not increment during Sleep. When the device wakes from Sleep, Timer1 will continue from its previous state. If Timer1 is clocked by an external clock source, then Capture mode will operate as defined in Section 15.1 "Capture Mode".
Timer1 must be running in Timer mode or Synchronized Counter mode for the CCP module to use the capture feature. In Asynchronous Counter mode or when Timer1 is clocked at FOSC, the capture operation may not work.
2010 Microchip Technology Inc.
DS41417A-page 125
PIC16F/LF722A/723A
TABLE 15-3:
Name ANSELB APFCON CCP1CON CCP2CON CCPRxL CCPRxH INTCON PIE1 PIE2 PIR1 PIR2 T1CON T1GCON TMR1L TMR1H TRISB TRISC Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH CAPTURE
Bit 7 -- -- -- -- Bit 6 -- -- -- -- Bit 5 ANSB5 -- DC1B1 DC2B1 Bit 4 ANSB4 -- DC1B0 DC2B0 Bit 3 ANSB3 -- CCP1M3 CCP2M3 Bit 2 ANSB2 -- CCP1M2 CCP2M2 Bit 1 ANSB1 SSSEL CCP1M1 CCP2M1 Bit 0 ANSB0 CCP2SEL CCP1M0 CCP2M0 Value on POR, BOR --11 1111 ---- --00 --00 0000 --00 0000 xxxx xxxx xxxx xxxx RBIE SSPIE -- SSPIF -- T1OSCEN T1GGO/ DONE T0IF CCP1IE -- CCP1IF -- T1SYNC T1GVAL INTF TMR2IE -- TMR2IF -- -- T1GSS1 RBIF TMR1IE CCP2IE TMR1IF CCP2IF TMR1ON T1GSS0 0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 0000 00-0 0000 0x00 xxxx xxxx xxxx xxxx TRISB1 TRISC1 TRISB0 TRISC0 1111 1111 1111 1111 Value on all other Resets --11 1111 ---- --00 --00 0000 --00 0000 uuuu uuuu uuuu uuuu 0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 uuuu uu-u 0000 0x00 uuuu uuuu uuuu uuuu 1111 1111 1111 1111
Capture/Compare/PWM Register X Low Byte Capture/Compare/PWM Register X High Byte GIE TMR1GIE -- TMR1GIF -- TMR1CS1 TMR1GE PEIE ADIE -- ADIF -- TMR1CS0 T1GPOL T0IE RCIE -- RCIF -- T1CKPS1 T1GTM INTE TXIE -- TXIF -- T1CKPS0 T1GSPM
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register Holding Register for the Most Significant Byte of the 16-bit TMR1 Register TRISB7 TRISC7 TRISB6 TRISC6 TRISB5 TRISC5 TRISB4 TRISC4 TRISB3 TRISC3 TRISB2 TRISC2
- = Unimplemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the Capture.
DS41417A-page 126
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
15.2 Compare Mode
15.2.2 TIMER1 MODE SELECTION
In Compare mode, the 16-bit CCPRx register value is constantly compared against the TMR1 register pair value. When a match occurs, the CCPx module may: * * * * * Toggle the CCPx output Set the CCPx output Clear the CCPx output Generate a Special Event Trigger Generate a Software Interrupt In Compare mode, Timer1 must be running in either Timer mode or Synchronized Counter mode. The compare operation may not work in Asynchronous Counter mode. Note: Clocking Timer1 from the system clock (FOSC) should not be used in Compare mode. For the Compare operation of the TMR1 register to the CCPRx register to occur, Timer1 must be clocked from the instruction clock (FOSC/4) or from an external clock source.
The action on the pin is based on the value of the CCPxM<3:0> control bits of the CCPxCON register. All Compare modes can generate an interrupt.
15.2.3
SOFTWARE INTERRUPT MODE
FIGURE 15-2:
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPxCON<3:0> Mode Select Set CCPxIF Interrupt Flag (PIRx) 4 CCPRxH CCPRxL
When Software Interrupt mode is chosen (CCPxM<3:0> = 1010), the CCPxIF bit in the PIRx register is set and the CCPx module does not assert control of the CCPx pin (refer to the CCPxCON register).
15.2.4
SPECIAL EVENT TRIGGER
CCPx Q S R TRIS Output Enable
When Special Event Trigger mode is chosen (CCPxM<3:0> = 1011), the CCPx module does the following: * Resets Timer1 * Starts an ADC conversion if ADC is enabled (CCP2 only) The CCPx module does not assert control of the CCPx pin in this mode (refer to the CCPxCON register). The Special Event Trigger output of the CCP occurs immediately upon a match between the TMR1H, TMR1L register pair and the CCPRxH, CCPRxL register pair. The TMR1H, TMR1L register pair is not reset until the next rising edge of the Timer1 clock. This allows the CCPRxH, CCPRxL register pair to effectively provide a 16-bit programmable period register for Timer1. Note 1: The Special Event Trigger from the CCP module does not set interrupt flag bit TMR1IF of the PIR1 register. 2: Removing the match condition by changing the contents of the CCPRxH and CCPRxL register pair, between the clock edge that generates the Special Event Trigger and the clock edge that generates the Timer1 Reset, will preclude the Reset from occurring.
Output Logic
Match
Comparator TMR1H TMR1L
Special Event Trigger Special Event Trigger will: * Clear TMR1H and TMR1L registers. * NOT set interrupt flag bit TMR1IF of the PIR1 register. * Set the GO/DONE bit to start the ADC conversion (CCP2 only).
15.2.1
CCPx PIN CONFIGURATION
The user must configure the CCPx pin as an output by clearing the associated TRIS bit. Either RC1 or RB3 can be selected as the CCP2 pin. Refer to Section 6.1 "Alternate Pin Function" for more information. Note: Clearing the CCPxCON register will force the CCPx compare output latch to the default low level. This is not the PORT I/O data latch.
15.2.5
COMPARE DURING SLEEP
The Compare mode is dependent upon the system clock (FOSC) for proper operation. Since FOSC is shut down during Sleep mode, the Compare mode will not function properly during Sleep.
2010 Microchip Technology Inc.
DS41417A-page 127
PIC16F/LF722A/723A
TABLE 15-4:
Name ADCON0 ANSELB APFCON CCP1CON CCP2CON CCPRxL CCPRxH INTCON PIE1 PIE2 PIR1 PIR2 T1CON T1GCON TMR1L TMR1H TRISB TRISC Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH COMPARE
Bit 7 -- -- -- -- -- Bit 6 -- -- -- -- -- Bit 5 CHS3 ANSB5 -- DC1B1 DC2B1 Bit 4 CHS2 ANSB4 -- DC1B0 DC2B0 Bit 3 CHS1 ANSB3 -- CCP1M3 CCP2M3 Bit 2 CHS0 ANSB2 -- CCP1M2 CCP2M2 Bit 1 GO/DONE ANSB1 SSSEL CCP1M1 CCP2M1 Bit 0 ADON ANSB0 CCP2SEL CCP1M0 CCP2M0 Value on POR, BOR --00 0000 --11 1111 ---- --00 --00 0000 --00 0000 xxxx xxxx xxxx xxxx RBIE SSPIE -- SSPIF -- T1OSCEN T1GGO/ DONE T0IF CCP1IE -- CCP1IF -- T1SYNC T1GVAL INTF TMR2IE -- TMR2IF -- -- T1GSS1 RBIF TMR1IE CCP2IE TMR1IF CCP2IF TMR1ON T1GSS0 0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 0000 00-0 0000 0x00 xxxx xxxx xxxx xxxx TRISB1 TRISC1 TRISB0 TRISC0 1111 1111 1111 1111 Value on all other Resets --00 0000 --11 1111 ---- --00 --00 0000 --00 0000 uuuu uuuu uuuu uuuu 0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 uuuu uu-u 0000 0x00 uuuu uuuu uuuu uuuu 1111 1111 1111 1111
Capture/Compare/PWM Register X Low Byte Capture/Compare/PWM Register X High Byte GIE TMR1GIE -- TMR1GIF -- TMR1CS1 TMR1GE PEIE ADIE -- ADIF -- TMR1CS0 T1GPOL T0IE RCIE -- RCIF -- T1CKPS1 T1GTM INTE TXIE -- TXIF -- T1CKPS0 T1GSPM
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register Holding Register for the Most Significant Byte of the 16-bit TMR1 Register TRISB7 TRISC7 TRISB6 TRISC6 TRISB5 TRISC5 TRISB4 TRISC4 TRISB3 TRISC3 TRISB2 TRISC2
- = Unimplemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the Compare.
DS41417A-page 128
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
15.3 PWM Mode
The PWM mode generates a Pulse-Width Modulated signal on the CCPx pin. The duty cycle, period and resolution are determined by the following registers: * * * * PR2 T2CON CCPRxL CCPxCON The PWM output (Figure 15-4) has a time base (period) and a time that the output stays high (duty cycle).
FIGURE 15-4:
Period Pulse Width
CCP PWM OUTPUT
TMR2 = PR2 TMR2 = CCPRxL:CCPxCON<5:4>
In Pulse-Width Modulation (PWM) mode, the CCP module produces up to a 10-bit resolution PWM output on the CCPx pin. Figure 15-3 shows a simplified block diagram of PWM operation. Figure 15-4 shows a typical waveform of the PWM signal. For a step-by-step procedure on how to set up the CCP module for PWM operation, refer to Section 15.3.8 "Setup for PWM Operation".
TMR2 = 0
15.3.1
CCPX PIN CONFIGURATION
In PWM mode, the CCPx pin is multiplexed with the PORT data latch. The user must configure the CCPx pin as an output by clearing the associated TRIS bit. Either RC1 or RB3 can be selected as the CCP2 pin. Refer to Section 6.1 "Alternate Pin Function" for more information. Note: Clearing the CCPxCON register will relinquish CCPx control of the CCPx pin.
FIGURE 15-3:
SIMPLIFIED PWM BLOCK DIAGRAM
CCPxCON<5:4>
Duty Cycle Registers CCPRxL
CCPRxH(2) (Slave) CCPx Comparator
(1)
R S
Q
TMR2
TRIS Comparator
PR2
Clear Timer2, toggle CCPx pin and latch duty cycle
Note 1:
2:
The 8-bit timer TMR2 register is concatenated with the 2-bit internal system clock (FOSC), or 2 bits of the prescaler, to create the 10-bit time base. In PWM mode, CCPRxH is a read-only register.
2010 Microchip Technology Inc.
DS41417A-page 129
PIC16F/LF722A/723A
15.3.2 PWM PERIOD EQUATION 15-2: PULSE WIDTH
The PWM period is specified by the PR2 register of Timer2. The PWM period can be calculated using the formula of Equation 15-1. Pulse Width = CCPRxL:CCPxCON<5:4> TOSC (TMR2 Prescale Value) Note: TOSC = 1/FOSC
EQUATION 15-1:
PWM PERIOD
PWM Period = PR2 + 1 4 TOSC (TMR2 Prescale Value) Note: TOSC = 1/FOSC
EQUATION 15-3:
DUTY CYCLE RATIO
CCPRxL:CCPxCON<5:4> Duty Cycle Ratio = ---------------------------------------------------------------------4 PR2 + 1 The CCPRxH register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. The 8-bit timer TMR2 register is concatenated with either the 2-bit internal system clock (FOSC), or 2 bits of the prescaler, to create the 10-bit time base. The system clock is used if the Timer2 prescaler is set to 1:1. When the 10-bit time base matches the CCPRxH and 2-bit latch, then the CCPx pin is cleared (refer to Figure 15-3).
When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCPx pin is set. (Exception: If the PWM duty cycle = 0%, the pin will not be set.) * The PWM duty cycle is latched from CCPRxL into CCPRxH. Note: The Timer2 postscaler (refer to Section 13.1 "Timer2 Operation") is not used in the determination of the PWM frequency.
15.3.3
PWM DUTY CYCLE
The PWM duty cycle is specified by writing a 10-bit value to multiple registers: CCPRxL register and DCxB<1:0> bits of the CCPxCON register. The CCPRxL contains the eight MSbs and the DCxB<1:0> bits of the CCPxCON register contain the two LSbs. CCPRxL and DCxB<1:0> bits of the CCPxCON register can be written to at any time. The duty cycle value is not latched into CCPRxH until after the period completes (i.e., a match between PR2 and TMR2 registers occurs). While using the PWM, the CCPRxH register is read-only. Equation 15-2 is used to calculate the PWM pulse width. Equation 15-3 is used to calculate the PWM duty cycle ratio.
DS41417A-page 130
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
15.3.4 PWM RESOLUTION EQUATION 15-4: PWM RESOLUTION
The resolution determines the number of available duty cycles for a given period. For example, a 10-bit resolution will result in 1024 discrete duty cycles, whereas an 8-bit resolution will result in 256 discrete duty cycles. The maximum PWM resolution is 10 bits when PR2 is 255. The resolution is a function of the PR2 register value as shown by Equation 15-4. Note: log 4 PR2 + 1 Resolution = ----------------------------------------- bits log 2
If the pulse width value is greater than the period the assigned PWM pin(s) will remain unchanged.
TABLE 15-5:
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 20 MHz)
1.22 kHz 16 0xFF 10 4.88 kHz 4 0xFF 10 19.53 kHz 1 0xFF 10 78.12 kHz 1 0x3F 8 156.3 kHz 1 0x1F 7 208.3 kHz 1 0x17 6.6
PWM Frequency Timer Prescale (1, 4, 16) PR2 Value Maximum Resolution (bits)
TABLE 15-6:
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 8 MHz)
1.22 kHz 16 0x65 8 4.90 kHz 4 0x65 8 19.61 kHz 1 0x65 8 76.92 kHz 1 0x19 6 153.85 kHz 1 0x0C 5 200.0 kHz 1 0x09 5
PWM Frequency Timer Prescale (1, 4, 16) PR2 Value Maximum Resolution (bits)
15.3.5
OPERATION IN SLEEP MODE
15.3.8
SETUP FOR PWM OPERATION
In Sleep mode, the TMR2 register will not increment and the state of the module will not change. If the CCPx pin is driving a value, it will continue to drive that value. When the device wakes up, TMR2 will continue from its previous state.
The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. Disable the PWM pin (CCPx) output driver(s) by setting the associated TRIS bit(s). Load the PR2 register with the PWM period value. Configure the CCP module for the PWM mode by loading the CCPxCON register with the appropriate values. Load the CCPRxL register and the DCxBx bits of the CCPxCON register, with the PWM duty cycle value. Configure and start Timer2: Clear the TMR2IF interrupt flag bit of the PIR1 register. See Note below. Configure the T2CKPS bits of the T2CON register with the Timer2 prescale value. Enable Timer2 by setting the TMR2ON bit of the T2CON register. Enable PWM output pin: Wait until Timer2 overflows, TMR2IF bit of the PIR1 register is set. See Note below. Enable the PWM pin (CCPx) output driver(s) by clearing the associated TRIS bit(s). In order to send a complete duty cycle and period on the first PWM output, the above steps must be included in the setup sequence. If it is not critical to start with a complete PWM signal on the first output, then step 6 may be ignored.
15.3.6
CHANGES IN SYSTEM CLOCK FREQUENCY
The PWM frequency is derived from the system clock frequency (FOSC). Any changes in the system clock frequency will result in changes to the PWM frequency. Refer to Section 7.0 "Oscillator Module" for additional details.
4.
5. * * * 6. * *
15.3.7
EFFECTS OF RESET
Any Reset will force all ports to Input mode and the CCP registers to their Reset states.
Note:
2010 Microchip Technology Inc.
DS41417A-page 131
PIC16F/LF722A/723A
TABLE 15-7:
Name ANSELB APFCON CCP1CON CCP2CON CCPRxL CCPRxH PR2 T2CON TMR2 TRISB TRISC Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH PWM
Bit 7 -- -- -- -- Bit 6 -- -- -- -- Bit 5 ANSB5 -- DC1B1 DC2B1 Bit 4 ANSB4 -- DC1B0 DC2B0 Bit 3 ANSB3 -- CCP1M3 CCP2M3 Bit 2 ANSB2 -- CCP1M2 CCP2M2 Bit 1 ANSB1 SSSEL CCP1M1 CCP2M1 Bit 0 ANSB0 CCP2SEL CCP1M0 CCP2M0 Value on POR, BOR --11 1111 ---- --00 --00 0000 --00 0000 xxxx xxxx xxxx xxxx 1111 1111 TOUTPS2 TRISB5 TRISC5 TOUTPS1 TRISB4 TRISC4 TOUTPS0 TRISB3 TRISC3 TMR2ON TRISB2 TRISC2 T2CKPS1 TRISB1 TRISC1 T2CKPS0 TRISB0 TRISC0 -000 0000 0000 0000 1111 1111 1111 1111 Value on all other Resets --11 1111 ---- --00 --00 0000 --00 0000 uuuu uuuu uuuu uuuu 1111 1111 -000 0000 0000 0000 1111 1111 1111 1111
Capture/Compare/PWM Register X Low Byte Capture/Compare/PWM Register X High Byte Timer2 Period Register -- TRISB7 TRISC7 TOUTPS3 TRISB6 TRISC6
Timer2 Module Register
- = Unimplemented locations, read as `0', u = unchanged, x = unknown. Shaded cells are not used by the PWM.
DS41417A-page 132
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.0 ADDRESSABLE UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER (AUSART)
The AUSART module includes the following capabilities: * * * * * * * * * * Full-duplex asynchronous transmit and receive Two-character input buffer One-character output buffer Programmable 8-bit or 9-bit character length Address detection in 9-bit mode Input buffer overrun error detection Received character framing error detection Half-duplex synchronous master Half-duplex synchronous slave Sleep operation
The Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART) module is a serial I/O communications peripheral. It contains all the clock generators, shift registers and data buffers necessary to perform an input or output serial data transfer independent of device program execution. The AUSART, also known as a Serial Communications Interface (SCI), can be configured as a full-duplex asynchronous system or half-duplex synchronous system. Full-Duplex mode is useful for communications with peripheral systems, such as CRT terminals and personal computers. Half-Duplex Synchronous mode is intended for communications with peripheral devices, such as A/D or D/A integrated circuits, serial EEPROMs or other microcontrollers. These devices typically do not have internal clocks for baud rate generation and require the external clock signal provided by a master synchronous device.
Block diagrams of the AUSART transmitter and receiver are shown in Figure 16-1 and Figure 16-2.
FIGURE 16-1:
AUSART TRANSMIT BLOCK DIAGRAM
Data Bus TXIE TXIF LSb Interrupt
TXREG Register 8 MSb (8)
TX/CK Pin Buffer and Control
***
Transmit Shift Register (TSR)
0
TXEN Baud Rate Generator TRMT FOSC /n n +1 SPBRG Multiplier SYNC BRGH x4 1 x x16 x64 0 1 0 0 TX9D TX9 SPEN
2010 Microchip Technology Inc.
DS41417A-page 133
PIC16F/LF722A/723A
FIGURE 16-2: AUSART RECEIVE BLOCK DIAGRAM
SPEN CREN OERR
RX/DT Pin Buffer and Control Baud Rate Generator FOSC Data Recovery
MSb Stop (8) 7
RSR Register
LSb 0 START
***
RX9
1
/n
+1 SPBRG
Multiplier SYNC BRGH
x4 1 x
x16 x64 0 1 0 0
n FIFO
FERR
RX9D
RCREG Register 8
Data Bus RCIF RCIE Interrupt
The operation of the AUSART module is controlled through two registers: * Transmit Status and Control (TXSTA) * Receive Status and Control (RCSTA) These registers are detailed in Register 16-1 and Register 16-2, respectively.
DS41417A-page 134
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.1 AUSART Asynchronous Mode
Note 1: When the SPEN bit is set the RX/DT I/O pin is automatically configured as an input, regardless of the state of the corresponding TRIS bit and whether or not the AUSART receiver is enabled. The RX/DT pin data can be read via a normal PORT read but PORT latch data output is precluded. 2: The TXIF transmitter interrupt flag is set when the TXEN enable bit is set. The AUSART transmits and receives data using the standard non-return-to-zero (NRZ) format. NRZ is implemented with two levels: a VOH mark state which represents a `1' data bit, and a VOL space state which represents a `0' data bit. NRZ refers to the fact that consecutively transmitted data bits of the same value stay at the output level of that bit without returning to a neutral level between each bit transmission. An NRZ transmission port idles in the mark state. Each character transmission consists of one Start bit followed by eight or nine data bits and is always terminated by one or more Stop bits. The Start bit is always a space and the Stop bits are always marks. The most common data format is 8 bits. Each transmitted bit persists for a period of 1/(Baud Rate). An on-chip dedicated 8-bit Baud Rate Generator is used to derive standard baud rate frequencies from the system oscillator. Refer to Table 16-5 for examples of baud rate configurations. The AUSART transmits and receives the LSb first. The AUSART's transmitter and receiver are functionally independent, but share the same data format and baud rate. Parity is not supported by the hardware, but can be implemented in software and stored as the ninth data bit.
16.1.1.2
Transmitting Data
16.1.1
AUSART ASYNCHRONOUS TRANSMITTER
A transmission is initiated by writing a character to the TXREG register. If this is the first character, or the previous character has been completely flushed from the TSR, the data in the TXREG is immediately transferred to the TSR register. If the TSR still contains all or part of a previous character, the new character data is held in the TXREG until the Stop bit of the previous character has been transmitted. The pending character in the TXREG is then transferred to the TSR in one TCY immediately following the Stop bit transmission. The transmission of the Start bit, data bits and Stop bit sequence commences immediately following the transfer of the data to the TSR from the TXREG.
16.1.1.3
Transmit Interrupt Flag
The AUSART transmitter block diagram is shown in Figure 16-1. The heart of the transmitter is the serial Transmit Shift Register (TSR), which is not directly accessible by software. The TSR obtains its data from the transmit buffer, which is the TXREG register.
16.1.1.1
Enabling the Transmitter
The AUSART transmitter is enabled for asynchronous operations by configuring the following three control bits: * TXEN = 1 * SYNC = 0 * SPEN = 1 All other AUSART control bits are assumed to be in their default state. Setting the TXEN bit of the TXSTA register enables the transmitter circuitry of the AUSART. Clearing the SYNC bit of the TXSTA register configures the AUSART for asynchronous operation. Setting the SPEN bit of the RCSTA register enables the AUSART and automatically configures the TX/CK I/O pin as an output.
The TXIF interrupt flag bit of the PIR1 register is set whenever the AUSART transmitter is enabled and no character is being held for transmission in the TXREG. In other words, the TXIF bit is only clear when the TSR is busy with a character and a new character has been queued for transmission in the TXREG. The TXIF flag bit is not cleared immediately upon writing TXREG. TXIF becomes valid in the second instruction cycle following the write execution. Polling TXIF immediately following the TXREG write will return invalid results. The TXIF bit is read-only, it cannot be set or cleared by software. The TXIF interrupt can be enabled by setting the TXIE interrupt enable bit of the PIE1 register. However, the TXIF flag bit will be set whenever the TXREG is empty, regardless of the state of TXIE enable bit. To use interrupts when transmitting data, set the TXIE bit only when there is more data to send. Clear the TXIE interrupt enable bit upon writing the last character of the transmission to the TXREG.
2010 Microchip Technology Inc.
DS41417A-page 135
PIC16F/LF722A/723A
16.1.1.4 TSR Status 16.1.1.6
1.
Asynchronous Transmission Set-up:
The TRMT bit of the TXSTA register indicates the status of the TSR register. This is a read-only bit. The TRMT bit is set when the TSR register is empty and is cleared when a character is transferred to the TSR register from the TXREG. The TRMT bit remains clear until all bits have been shifted out of the TSR register. No interrupt logic is tied to this bit, so the user has to poll this bit to determine the TSR status. Note: The TSR register is not mapped in data memory, so it is not available to the user.
2. 3.
16.1.1.5
Transmitting 9-Bit Characters
4.
The AUSART supports 9-bit character transmissions. When the TX9 bit of the TXSTA register is set, the AUSART will shift 9 bits out for each character transmitted. The TX9D bit of the TXSTA register is the ninth, and Most Significant, data bit. When transmitting 9-bit data, the TX9D data bit must be written before writing the 8 Least Significant bits into the TXREG. All nine bits of data will be transferred to the TSR shift register immediately after the TXREG is written. A special 9-bit Address mode is available for use with multiple receivers. Refer to Section 16.1.2.7 "Address Detection" for more information on the Address mode.
5.
6. 7.
Initialize the SPBRG register and the BRGH bit to achieve the desired baud rate (Refer to Section 16.2 "AUSART Baud Rate Generator (BRG)"). Enable the asynchronous serial port by clearing the SYNC bit and setting the SPEN bit. If 9-bit transmission is desired, set the TX9 control bit. A set ninth data bit will indicate that the 8 Least Significant data bits are an address when the receiver is set for address detection. Enable the transmission by setting the TXEN control bit. This will cause the TXIF interrupt bit to be set. If interrupts are desired, set the TXIE interrupt enable bit of the PIE1 register. An interrupt will occur immediately provided that the GIE and PEIE bits of the INTCON register are also set. If 9-bit transmission is selected, the ninth bit should be loaded into the TX9D data bit. Load 8-bit data into the TXREG register. This will start the transmission.
FIGURE 16-3:
Write to TXREG BRG Output (Shift Clock) TX/CK pin TXIF bit (Transmit Buffer Empty Flag)
ASYNCHRONOUS TRANSMISSION
Word 1
Start bit 1 TCY
bit 0
bit 1 Word 1
bit 7/8
Stop bit
TRMT bit (Transmit Shift Reg. Empty Flag)
Word 1 Transmit Shift Reg
FIGURE 16-4:
Write to TXREG BRG Output (Shift Clock) TX/CK pin TXIF bit (Transmit Buffer Empty Flag) TRMT bit (Transmit Shift Reg. Empty Flag)
ASYNCHRONOUS TRANSMISSION (BACK-TO-BACK)
Word 1 Word 2
Start bit 1 TCY
bit 0
bit 1 Word 1
bit 7/8
Stop bit
Start bit Word 2
bit 0
1 TCY Word 1 Transmit Shift Reg. Word 2 Transmit Shift Reg.
Note:
This timing diagram shows two consecutive transmissions.
DS41417A-page 136
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 16-1:
Name INTCON PIE1 PIR1 RCSTA SPBRG TRISC TXREG TXSTA Legend:
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Bit 6 PEIE ADIE ADIF RX9 BRG6 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN BRG5 TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN BRG4 TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN BRG3 TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR BRG2 TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR BRG1 TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D BRG0 TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 0000 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 0000 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN BRG7 TRISC7 CSRC
AUSART Transmit Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Asynchronous Transmission.
2010 Microchip Technology Inc.
DS41417A-page 137
PIC16F/LF722A/723A
16.1.2 AUSART ASYNCHRONOUS RECEIVER 16.1.2.2 Receiving Data
The Asynchronous mode is typically used in RS-232 systems. The receiver block diagram is shown in Figure 16-2. The data is received on the RX/DT pin and drives the data recovery block. The data recovery block is actually a high-speed shifter operating at 16 times the baud rate, whereas the serial Receive Shift Register (RSR) operates at the bit rate. When all 8 or 9 bits of the character have been shifted in, they are immediately transferred to a two character First-In First-Out (FIFO) memory. The FIFO buffering allows reception of two complete characters and the start of a third character before software must start servicing the AUSART receiver. The FIFO and RSR registers are not directly accessible by software. Access to the received data is via the RCREG register. The receiver data recovery circuit initiates character reception on the falling edge of the first bit. The first bit, also known as the Start bit, is always a zero. The data recovery circuit counts one-half bit time to the center of the Start bit and verifies that the bit is still a zero. If it is not a zero then the data recovery circuit aborts character reception, without generating an error, and resumes looking for the falling edge of the Start bit. If the Start bit zero verification succeeds then the data recovery circuit counts a full bit time to the center of the next bit. The bit is then sampled by a majority detect circuit and the resulting `0' or `1' is shifted into the RSR. This repeats until all data bits have been sampled and shifted into the RSR. One final bit time is measured and the level sampled. This is the Stop bit, which is always a `1'. If the data recovery circuit samples a `0' in the Stop bit position then a framing error is set for this character, otherwise the framing error is cleared for this character. Refer to Section 16.1.2.4 "Receive Framing Error" for more information on framing errors. Immediately after all data bits and the Stop bit have been received, the character in the RSR is transferred to the AUSART receive FIFO and the RCIF interrupt flag bit of the PIR1 register is set. The top character in the FIFO is transferred out of the FIFO by reading the RCREG register. Note: If the receive FIFO is overrun, no additional characters will be received until the overrun condition is cleared. Refer to Section 16.1.2.5 "Receive Overrun Error" for more information on overrun errors.
16.1.2.1
Enabling the Receiver
The AUSART receiver is enabled for asynchronous operation by configuring the following three control bits: * CREN = 1 * SYNC = 0 * SPEN = 1 All other AUSART control bits are assumed to be in their default state. Setting the CREN bit of the RCSTA register enables the receiver circuitry of the AUSART. Clearing the SYNC bit of the TXSTA register configures the AUSART for asynchronous operation. Setting the SPEN bit of the RCSTA register enables the AUSART and automatically configures the RX/DT I/O pin as an input. Note: When the SPEN bit is set the TX/CK I/O pin is automatically configured as an output, regardless of the state of the corresponding TRIS bit and whether or not the AUSART transmitter is enabled. The PORT latch is disconnected from the output driver so it is not possible to use the TX/CK pin as a general purpose output.
16.1.2.3
Receive Interrupts
The RCIF interrupt flag bit of the PIR1 register is set whenever the AUSART receiver is enabled and there is an unread character in the receive FIFO. The RCIF interrupt flag bit is read-only, it cannot be set or cleared by software. RCIF interrupts are enabled by setting all of the following bits: * RCIE, Receive Interrupt Enable bit of the PIE1 register * PEIE, Peripheral Interrupt Enable bit of the INTCON register * GIE, Global Interrupt Enable bit of the INTCON register The RCIF interrupt flag bit of the PIR1 register will be set when there is an unread character in the FIFO, regardless of the state of interrupt enable bits.
DS41417A-page 138
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.1.2.4 Receive Framing Error 16.1.2.7 Address Detection
Each character in the receive FIFO buffer has a corresponding framing error Status bit. A framing error indicates that a Stop bit was not seen at the expected time. The framing error status is accessed via the FERR bit of the RCSTA register. The FERR bit represents the status of the top unread character in the receive FIFO. Therefore, the FERR bit must be read before reading the RCREG. The FERR bit is read-only and only applies to the top unread character in the receive FIFO. A framing error (FERR = 1) does not preclude reception of additional characters. It is not necessary to clear the FERR bit. Reading the next character from the FIFO buffer will advance the FIFO to the next character and the next corresponding framing error. The FERR bit can be forced clear by clearing the SPEN bit of the RCSTA register which resets the AUSART. Clearing the CREN bit of the RCSTA register does not affect the FERR bit. A framing error by itself does not generate an interrupt. Note: If all receive characters in the receive FIFO have framing errors, repeated reads of the RCREG will not clear the FERR bit. A special Address Detection mode is available for use when multiple receivers share the same transmission line, such as in RS-485 systems. Address detection is enabled by setting the ADDEN bit of the RCSTA register. Address detection requires 9-bit character reception. When address detection is enabled, only characters with the ninth data bit set will be transferred to the receive FIFO buffer, thereby setting the RCIF interrupt bit of the PIR1 register. All other characters will be ignored. Upon receiving an address character, user software determines if the address matches its own. Upon address match, user software must disable address detection by clearing the ADDEN bit before the next Stop bit occurs. When user software detects the end of the message, determined by the message protocol used, software places the receiver back into the Address Detection mode by setting the ADDEN bit.
16.1.2.5
Receive Overrun Error
The receive FIFO buffer can hold two characters. An overrun error will be generated if a third character, in its entirety, is received before the FIFO is accessed. When this happens the OERR bit of the RCSTA register is set. The characters already in the FIFO buffer can be read but no additional characters will be received until the error is cleared. The error must be cleared by either clearing the CREN bit of the RCSTA register or by setting the AUSART by clearing the SPEN bit of the RCSTA register.
16.1.2.6
Receiving 9-bit Characters
The AUSART supports 9-bit character reception. When the RX9 bit of the RCSTA register is set the AUSART will shift 9 bits into the RSR for each character received. The RX9D bit of the RCSTA register is the ninth and Most Significant data bit of the top unread character in the receive FIFO. When reading 9-bit data from the receive FIFO buffer, the RX9D data bit must be read before reading the 8 Least Significant bits from the RCREG.
2010 Microchip Technology Inc.
DS41417A-page 139
PIC16F/LF722A/723A
16.1.2.8
1.
Asynchronous Reception Set-up:
16.1.2.9
9-bit Address Detection Mode Set-up
2.
3.
4. 5. 6.
7.
8.
9.
Initialize the SPBRG register and the BRGH bit to achieve the desired baud rate (refer to Section 16.2 "AUSART Baud Rate Generator (BRG)"). Enable the serial port by setting the SPEN bit. The SYNC bit must be clear for asynchronous operation. If interrupts are desired, set the RCIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. If 9-bit reception is desired, set the RX9 bit. Enable reception by setting the CREN bit. The RCIF interrupt flag bit of the PIR1 register will be set when a character is transferred from the RSR to the receive buffer. An interrupt will be generated if the RCIE bit of the PIE1 register was also set. Read the RCSTA register to get the error flags and, if 9-bit data reception is enabled, the ninth data bit. Get the received 8 Least Significant data bits from the receive buffer by reading the RCREG register. If an overrun occurred, clear the OERR flag by clearing the CREN receiver enable bit.
This mode would typically be used in RS-485 systems. To set up an Asynchronous Reception with Address Detect Enable: 1. Initialize the SPBRG register and the BRGH bit to achieve the desired baud rate (refer to Section 16.2 "AUSART Baud Rate Generator (BRG)"). 2. Enable the serial port by setting the SPEN bit. The SYNC bit must be clear for asynchronous operation. 3. If interrupts are desired, set the RCIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. 4. Enable 9-bit reception by setting the RX9 bit. 5. Enable address detection by setting the ADDEN bit. 6. Enable reception by setting the CREN bit. 7. The RCIF interrupt flag bit of the PIR1 register will be set when a character with the ninth bit set is transferred from the RSR to the receive buffer. An interrupt will be generated if the RCIE interrupt enable bit of the PIE1 register was also set. 8. Read the RCSTA register to get the error flags. The ninth data bit will always be set. 9. Get the received 8 Least Significant data bits from the receive buffer by reading the RCREG register. Software determines if this is the device's address. 10. If an overrun occurred, clear the OERR flag by clearing the CREN receiver enable bit. 11. If the device has been addressed, clear the ADDEN bit to allow all received data into the receive buffer and generate interrupts.
FIGURE 16-5:
RX/DT pin Rcv Shift Reg Rcv Buffer Reg Read Rcv Buffer Reg RCREG RCIF (Interrupt Flag) OERR bit CREN
ASYNCHRONOUS RECEPTION
Start bit bit 0 bit 1 bit 7/8 Stop bit Start bit bit 0 bit 7/8 Stop bit Start bit bit 7/8 Stop bit
Word 1 RCREG
Word 2 RCREG
Note:
This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word, causing the OERR (overrun) bit to be set.
DS41417A-page 140
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 16-2:
Name INTCON PIE1 PIR1 RCREG RCSTA SPBRG TRISC TXSTA Legend:
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Bit 6 PEIE ADIE ADIF RX9 BRG6 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN BRG5 TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN BRG4 TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN BRG3 TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR BRG2 TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR BRG1 TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D BRG0 TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN BRG7 TRISC7 CSRC
AUSART Receive Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Asynchronous Reception.
2010 Microchip Technology Inc.
DS41417A-page 141
PIC16F/LF722A/723A
REGISTER 16-1:
R/W-0 CSRC bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
TXSTA: TRANSMIT STATUS AND CONTROL REGISTER
R/W-0 TX9 R/W-0 TXEN(1) R/W-0 SYNC U-0 -- R/W-0 BRGH R-1 TRMT R/W-0 TX9D bit 0
CSRC: Clock Source Select bit Asynchronous mode: Don't care Synchronous mode: 1 = Master mode (clock generated internally from BRG) 0 = Slave mode (clock from external source) TX9: 9-bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission TXEN: Transmit Enable bit(1) 1 = Transmit enabled 0 = Transmit disabled SYNC: AUSART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode Unimplemented: Read as `0' BRGH: High Baud Rate Select bit Asynchronous mode: 1 = High speed 0 = Low speed Synchronous mode: Unused in this mode TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full TX9D: Ninth bit of Transmit Data Can be address/data bit or a parity bit. SREN/CREN overrides TXEN in Synchronous mode.
bit 6
bit 5
bit 4
bit 3 bit 2
bit 1
bit 0 Note 1:
DS41417A-page 142
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 16-2:
R/W-0 SPEN bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
RCSTA: RECEIVE STATUS AND CONTROL REGISTER
R/W-0 RX9 R/W-0 SREN R/W-0 CREN R/W-0 ADDEN R-0 FERR R-0 OERR R-x RX9D bit 0
SPEN: Serial Port Enable bit(1) 1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins) 0 = Serial port disabled (held in Reset) RX9: 9-bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception SREN: Single Receive Enable bit Asynchronous mode: Don't care Synchronous mode - Master: 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode - Slave: Don't care CREN: Continuous Receive Enable bit Asynchronous mode: 1 = Enables receiver 0 = Disables receiver Synchronous mode: 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive ADDEN: Address Detect Enable bit Asynchronous mode 9-bit (RX9 = 1): 1 = Enables address detection, enable interrupt and load the receive buffer when RSR<8> is set 0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit Asynchronous mode 8-bit (RX9 = 0): Don't care Synchronous mode: Must be set to `0' FERR: Framing Error bit 1 = Framing error (can be updated by reading RCREG register and receive next valid byte) 0 = No framing error OERR: Overrun Error bit 1 = Overrun error (can be cleared by clearing bit CREN) 0 = No overrun error RX9D: Ninth bit of Received Data This can be address/data bit or a parity bit and must be calculated by user firmware.
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1: The AUSART module automatically changes the pin from tri-state to drive as needed. Configure TRISx = 1.
2010 Microchip Technology Inc.
DS41417A-page 143
PIC16F/LF722A/723A
16.2 AUSART Baud Rate Generator (BRG)
EXAMPLE 16-1: CALCULATING BAUD RATE ERROR
For a device with FOSC of 16 MHz, desired baud rate of 9600, and Asynchronous mode with SYNC = 0 and BRGH = 0 (as seen in Table 16-3): FOSC Desired Baud Rate = -------------------------------------64 SPBRG + 1 Solving for SPBRG: FOSC SPBRG = -------------------------------------------------------- - 1 64 Desired Baud Rate 16000000 = ----------------------- - 1 64 9600 = 25.042 = 25 16000000 Actual Baud Rate = -------------------------64 25 + 1 = 9615 Actual Baud Rate - Desired Baud Rate % Error = ------------------------------------------------------------------------------------------------- 100 Desired Baud Rate 9615 - 9600 = ----------------------------- 100 = 0.16% 9600
The Baud Rate Generator (BRG) is an 8-bit timer that is dedicated to the support of both the asynchronous and synchronous AUSART operation. The SPBRG register determines the period of the free running baud rate timer. In Asynchronous mode the multiplier of the baud rate period is determined by the BRGH bit of the TXSTA register. In Synchronous mode, the BRGH bit is ignored. Table 16-3 contains the formulas for determining the baud rate. Example 16-1 provides a sample calculation for determining the baud rate and baud rate error. Typical baud rates and error values for various asynchronous modes have been computed for your convenience and are shown in Table 16-3. It may be advantageous to use the high baud rate (BRGH = 1), to reduce the baud rate error. Writing a new value to the SPBRG register causes the BRG timer to be reset (or cleared). This ensures that the BRG does not wait for a timer overflow before outputting the new baud rate.
TABLE 16-3:
SYNC 0 0 1 Legend:
BAUD RATE FORMULAS
BRGH 0 1 x AUSART Mode Asynchronous Asynchronous Synchronous Baud Rate Formula FOSC/[64 (n+1)] FOSC/[16 (n+1)] FOSC/[4 (n+1)]
Configuration Bits
x = Don't care, n = value of SPBRG register
TABLE 16-4:
Name RCSTA SPBRG TXSTA Legend:
REGISTERS ASSOCIATED WITH THE BAUD RATE GENERATOR
Bit 6 RX9 BRG6 TX9 Bit 5 SREN BRG5 TXEN Bit 4 CREN BRG4 SYNC Bit 3 ADDEN BRG3 -- Bit 2 FERR BRG2 BRGH Bit 1 OERR BRG1 TRMT Bit 0 RX9D BRG0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 -010
Bit 7 SPEN BRG7 CSRC
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for the Baud Rate Generator.
DS41417A-page 144
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 16-5:
BAUD RATE
BAUD RATES FOR ASYNCHRONOUS MODES
SYNC = 0, BRGH = 0 FOSC = 18.432 MHz Actual Rate -- 1200 2400 9600 10286 19.20k 57.60k -- % Error -- 0.00 0.00 0.00 -1.26 0.00 0.00 -- SPBRG value (decimal) -- 239 119 29 27 14 7 -- FOSC = 16.0000 MHz Actual Rate -- 1201 2403 9615 10416 19.23k -- -- % Error -- 0.08 0.16 0.16 -0.01 0.16 -- -- SPBRG value (decimal) -- 207 103 25 23 12 -- -- FOSC = 11.0592 MHz Actual Rate -- 1200 2400 9600 10165 19.20k 57.60k -- % Error -- 0.00 0.00 0.00 -2.42 0.00 0.00 -- SPBRG value (decimal) -- 143 71 17 16 8 2 --
FOSC = 20.000 MHz Actual Rate -- 1221 2404 9470 10417 19.53k -- -- % Error -- 1.73 0.16 -1.36 0.00 1.73 -- -- SPBRG value (decimal) -- 255 129 32 29 15 -- --
300 1200 2400 9600 10417 19.2k 57.6k 115.2k
SYNC = 0, BRGH = 0 BAUD RATE FOSC = 8.000 MHz Actual Rate -- 1202 2404 9615 10417 -- -- -- % Error -- 0.16 0.16 0.16 0.00 -- -- -- SPBRG value (decimal) -- 103 51 12 11 -- -- -- FOSC = 4.000 MHz Actual Rate 300 1202 2404 -- 10417 -- -- -- % Error 0.16 0.16 0.16 -- 0.00 -- -- -- SPBRG value (decimal) 207 51 25 -- 5 -- -- -- FOSC = 3.6864 MHz Actual Rate 300 1200 2400 9600 -- 19.20k 57.60k -- % Error 0.00 0.00 0.00 0.00 -- 0.00 0.00 -- SPBRG value (decimal) 191 47 23 5 -- 2 0 -- FOSC = 1.000 MHz Actual Rate 300 1202 -- -- -- -- -- -- % Error 0.16 0.16 -- -- -- -- -- -- SPBRG value (decimal) 51 12 -- -- -- -- -- --
300 1200 2400 9600 10417 19.2k 57.6k 115.2k
SYNC = 0, BRGH = 1 BAUD RATE FOSC = 20.000 MHz Actual Rate -- -- -- 9615 10417 19.23k 56.82k 113.64k % Error -- -- -- 0.16 0.00 0.16 -1.36 -1.36 SPBRG value (decimal) -- -- -- 129 119 64 21 10 FOSC = 18.432 MHz Actual Rate -- -- -- 9600 10378 19.20k 57.60k 115.2k % Error -- -- -- 0.00 -0.37 0.00 0.00 0.00 SPBRG value (decimal) -- -- -- 119 110 59 19 9 FOSC = 16.0000 MHz Actual Rate -- -- -- 9615 10417 19.23k 58.8k -- % Error -- -- -- 0.16 0.00 0.16 2.12 -- SPBRG value (decimal) -- -- -- 103 95 51 16 -- FOSC = 11.0592 MHz Actual Rate -- -- -- 9600 10473 19.20k 57.60k 115.2k % Error -- -- -- 0.00 0.53 0.00 0.00 0.00 SPBRG value (decimal) -- -- -- 71 65 35 11 5
300 1200 2400 9600 10417 19.2k 57.6k 115.2k
2010 Microchip Technology Inc.
DS41417A-page 145
PIC16F/LF722A/723A
TABLE 16-5:
BAUD RATE
BAUD RATES FOR ASYNCHRONOUS MODES
SYNC = 0, BRGH = 1 FOSC = 4.000 MHz Actual Rate -- 1202 2404 9615 10417 19.23k -- -- % Error -- 0.16 0.16 0.16 0.00 0.16 -- -- SPBRG value (decimal) -- 207 103 25 23 12 -- -- FOSC = 3.6864 MHz Actual Rate -- 1200 2400 9600 10473 19.2k 57.60k 115.2k % Error -- 0.00 0.00 0.00 0.53 0.00 0.00 0.00 SPBRG value (decimal) -- 191 95 23 21 11 3 1 FOSC = 1.000 MHz Actual Rate 300 1202 2404 -- 10417 -- -- -- % Error 0.16 0.16 0.16 -- 0.00 -- -- -- SPBRG value (decimal) 207 51 25 -- 5 -- -- --
FOSC = 8.000 MHz Actual Rate -- -- 2404 9615 10417 19231 55556 -- % Error -- -- 0.16 0.16 0.00 0.16 -3.55 -- SPBRG value (decimal) -- -- 207 51 47 25 8 --
300 1200 2400 9600 10417 19.2k 57.6k 115.2k
DS41417A-page 146
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.3 AUSART Synchronous Mode
16.3.1.2 Synchronous Master Transmission
Synchronous serial communications are typically used in systems with a single master and one or more slaves. The master device contains the necessary circuitry for baud rate generation and supplies the clock for all devices in the system. Slave devices can take advantage of the master clock by eliminating the internal clock generation circuitry. There are two signal lines in Synchronous mode: a bidirectional data line and a clock line. Slaves use the external clock supplied by the master to shift the serial data into and out of their respective receive and transmit shift registers. Since the data line is bidirectional, synchronous operation is half-duplex only. Half-duplex refers to the fact that master and slave devices can receive and transmit data but not both simultaneously. The AUSART can operate as either a master or slave device. Start and Stop bits are not used in synchronous transmissions. Data is transferred out of the device on the RX/DT pin. The RX/DT and TX/CK pin output drivers are automatically enabled when the AUSART is configured for synchronous master transmit operation. A transmission is initiated by writing a character to the TXREG register. If the TSR still contains all or part of a previous character, the new character data is held in the TXREG until the last bit of the previous character has been transmitted. If this is the first character, or the previous character has been completely flushed from the TSR, the data in the TXREG is immediately transferred to the TSR. The transmission of the character commences immediately following the transfer of the data to the TSR from the TXREG. Each data bit changes on the leading edge of the master clock and remains valid until the subsequent leading clock edge. Note: The TSR register is not mapped in data memory, so it is not available to the user.
16.3.1
SYNCHRONOUS MASTER MODE
16.3.1.3
1.
The following bits are used to configure the AUSART for Synchronous Master operation: * * * * * SYNC = 1 CSRC = 1 SREN = 0 (for transmit); SREN = 1 (for receive) CREN = 0 (for transmit); CREN = 1 (for receive) SPEN = 1
Synchronous Master Transmission Set-up:
2. 3. 4. 5. 6.
Setting the SYNC bit of the TXSTA register configures the device for synchronous operation. Setting the CSRC bit of the TXSTA register configures the device as a master. Clearing the SREN and CREN bits of the RCSTA register ensures that the device is in the Transmit mode, otherwise the device will be configured to receive. Setting the SPEN bit of the RCSTA register enables the AUSART.
7. 8.
16.3.1.1
Master Clock
Synchronous data transfers use a separate clock line, which is synchronous with the data. A device configured as a master transmits the clock on the TX/CK line. The TX/CK pin output driver is automatically enabled when the AUSART is configured for synchronous transmit or receive operation. Serial data bits change on the leading edge to ensure they are valid at the trailing edge of each clock. One clock cycle is generated for each data bit. Only as many clock cycles are generated as there are data bits.
Initialize the SPBRG register and the BRGH bit to achieve the desired baud rate (refer to Section 16.2 "AUSART Baud Rate Generator (BRG)"). Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. Disable Receive mode by clearing bits SREN and CREN. Enable Transmit mode by setting the TXEN bit. If 9-bit transmission is desired, set the TX9 bit. If interrupts are desired, set the TXIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. If 9-bit transmission is selected, the ninth bit should be loaded in the TX9D bit. Start transmission by loading data to the TXREG register.
2010 Microchip Technology Inc.
DS41417A-page 147
PIC16F/LF722A/723A
FIGURE 16-6:
RX/DT pin TX/CK pin Write to TXREG Reg TXIF bit (Interrupt Flag) TRMT bit `1' Synchronous Master mode, SPBRG = 0, continuous transmission of two 8-bit words. `1' Write Word 1 Write Word 2
SYNCHRONOUS TRANSMISSION
bit 0 bit 1 bit 2 bit 7 bit 0 bit 1 bit 7
Word 1
Word 2
TXEN bit
Note:
FIGURE 16-7:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
RX/DT pin bit 0 bit 1 bit 2 bit 6 bit 7
TX/CK pin Write to TXREG Reg
TXIF bit
TRMT bit
TXEN bit
TABLE 16-6:
Name INTCON PIE1 PIR1 RCSTA SPBRG TRISC TXREG TXSTA Legend:
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Bit 6 PEIE ADIE ADIF RX9 BRG6 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN BRG5 TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN BRG4 TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN BRG3 TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR BRG2 TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR BRG1 TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D BRG0 TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 0000 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 000x 0000 0000 1111 1111 0000 0000 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN BRG7 TRISC7 CSRC
AUSART Transmit Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Synchronous Master Transmission.
DS41417A-page 148
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.3.1.4 Synchronous Master Reception 16.3.1.7 Receiving 9-bit Characters
Data is received at the RX/DT pin. The RX/DT pin output driver is automatically disabled when the AUSART is configured for synchronous master receive operation. In Synchronous mode, reception is enabled by setting either the Single Receive Enable bit (SREN of the RCSTA register) or the Continuous Receive Enable bit (CREN of the RCSTA register). When SREN is set and CREN is clear, only as many clock cycles are generated as there are data bits in a single character. The SREN bit is automatically cleared at the completion of one character. When CREN is set, clocks are continuously generated until CREN is cleared. If CREN is cleared in the middle of a character the CK clock stops immediately and the partial character is discarded. If SREN and CREN are both set, then SREN is cleared at the completion of the first character and CREN takes precedence. To initiate reception, set either SREN or CREN. Data is sampled at the RX/DT pin on the trailing edge of the TX/CK clock pin and is shifted into the Receive Shift Register (RSR). When a complete character is received into the RSR, the RCIF bit of the PIR1 register is set and the character is automatically transferred to the two character receive FIFO. The Least Significant eight bits of the top character in the receive FIFO are available in RCREG. The RCIF bit remains set as long as there are un-read characters in the receive FIFO. The AUSART supports 9-bit character reception. When the RX9 bit of the RCSTA register is set, the AUSART will shift 9-bits into the RSR for each character received. The RX9D bit of the RCSTA register is the ninth, and Most Significant, data bit of the top unread character in the receive FIFO. When reading 9-bit data from the receive FIFO buffer, the RX9D data bit must be read before reading the 8 Least Significant bits from the RCREG. Address detection in Synchronous modes is not supported, therefore the ADDEN bit of the RCSTA register must be cleared.
16.3.1.8
1.
Synchronous Master Reception Setup:
16.3.1.5
Slave Clock
Synchronous data transfers use a separate clock line, which is synchronous with the data. A device configured as a slave receives the clock on the TX/CK line. The TX/ CK pin output driver is automatically disabled when the device is configured for synchronous slave transmit or receive operation. Serial data bits change on the leading edge to ensure they are valid at the trailing edge of each clock. One data bit is transferred for each clock cycle. Only as many clock cycles should be received as there are data bits.
16.3.1.6
Receive Overrun Error
The receive FIFO buffer can hold two characters. An overrun error will be generated if a third character, in its entirety, is received before RCREG is read to access the FIFO. When this happens the OERR bit of the RCSTA register is set. Previous data in the FIFO will not be overwritten. The two characters in the FIFO buffer can be read, however, no additional characters will be received until the error is cleared. The OERR bit can only be cleared by clearing the overrun condition. If the overrun error occurred when the SREN bit is set and CREN is clear then the error is cleared by reading RCREG. If the overrun occurred when the CREN bit is set then the error condition is cleared by either clearing the CREN bit of the RCSTA register.
Initialize the SPBRG register for the appropriate baud rate. Set or clear the BRGH bit, as required, to achieve the desired baud rate. 2. Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. 3. Ensure bits CREN and SREN are clear. 4. If interrupts are desired, set the RCIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. 5. If 9-bit reception is desired, set bit RX9. 6. Verify address detection is disabled by clearing the ADDEN bit of the RCSTA register. 7. Start reception by setting the SREN bit or for continuous reception, set the CREN bit. 8. Interrupt flag bit RCIF of the PIR1 register will be set when reception of a character is complete. An interrupt will be generated if the RCIE interrupt enable bit of the PIE1 register was set. 9. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 10. Read the 8-bit received data by reading the RCREG register. 11. If an overrun error occurs, clear the error by either clearing the CREN bit of the RCSTA register or by clearing the SPEN bit, which resets the AUSART.
2010 Microchip Technology Inc.
DS41417A-page 149
PIC16F/LF722A/723A
FIGURE 16-8:
RX/DT pin TX/CK pin Write to bit SREN SREN bit CREN bit `0' RCIF bit (Interrupt) Read RCREG Note: Timing diagram demonstrates Synchronous Master mode with bit SREN = 1 and bit BRGH = 0. `0'
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
TABLE 16-7:
Name INTCON PIE1 PIR1 RCREG RCSTA TRISC TXSTA Legend:
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Bit 6 PEIE ADIE ADIF RX9 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 0000 0000 000X 1111 1111 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 0000 0000 000X 1111 1111 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN TRISC7 CSRC
AUSART Receive Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Synchronous Master Reception.
DS41417A-page 150
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.3.2 SYNCHRONOUS SLAVE MODE
The following bits are used to configure the AUSART for Synchronous slave operation: * * * * * SYNC = 1 CSRC = 0 SREN = 0 (for transmit); SREN = 1 (for receive) CREN = 0 (for transmit); CREN = 1 (for receive) SPEN = 1 If two words are written to the TXREG and then the SLEEP instruction is executed, the following will occur: 1. 2. 3. 4. The first character will immediately transfer to the TSR register and transmit. The second word will remain in TXREG register. The TXIF bit will not be set. After the first character has been shifted out of TSR, the TXREG register will transfer the second character to the TSR and the TXIF bit will now be set. If the PEIE and TXIE bits are set, the interrupt will wake the device from Sleep and execute the next instruction. If the GIE bit is also set, the program will call the Interrupt Service Routine.
Setting the SYNC bit of the TXSTA register configures the device for synchronous operation. Clearing the CSRC bit of the TXSTA register configures the device as a slave. Clearing the SREN and CREN bits of the RCSTA register ensures that the device is in the Transmit mode, otherwise the device will be configured to receive. Setting the SPEN bit of the RCSTA register enables the AUSART.
5.
16.3.2.2
1. 2. 3.
Synchronous Slave Transmission Set-up:
16.3.2.1
AUSART Synchronous Slave Transmit
The operation of the Synchronous Master and Slave modes are identical (refer to Section 16.3.1.2 "Synchronous Master Transmission"), except in the case of the Sleep mode.
4. 5. 6. 7. 8.
Set the SYNC and SPEN bits and clear the CSRC bit. Clear the CREN and SREN bits. If using interrupts, ensure that the GIE and PEIE bits of the INTCON register are set and set the TXIE bit. If 9-bit transmission is desired, set the TX9 bit. Enable transmission by setting the TXEN bit. Verify address detection is disabled by clearing the ADDEN bit of the RCSTA register. If 9-bit transmission is selected, insert the Most Significant bit into the TX9D bit. Start transmission by writing the Least Significant 8 bits to the TXREG register.
TABLE 16-8:
Name INTCON PIE1 PIR1 RCSTA TRISC TXREG TXSTA Legend:
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Bit 6 PEIE ADIE ADIF RX9 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 000X 1111 1111 0000 0000 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 000X 1111 1111 0000 0000 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN TRISC7 CSRC
AUSART Transmit Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Synchronous Slave Transmission.
2010 Microchip Technology Inc.
DS41417A-page 151
PIC16F/LF722A/723A
16.3.2.3 AUSART Synchronous Slave Reception 16.3.2.4
1. 2.
Synchronous Slave Reception Setup:
The operation of the Synchronous Master and Slave modes is identical (Section 16.3.1.4 "Synchronous Master Reception"), with the following exceptions: * Sleep * CREN bit is always set, therefore the receiver is never Idle * SREN bit, which is a "don't care" in Slave mode A character may be received while in Sleep mode by setting the CREN bit prior to entering Sleep. Once the word is received, the RSR register will transfer the data to the RCREG register. If the RCIE interrupt enable bit of the PIE1 register is set, the interrupt generated will wake the device from Sleep and execute the next instruction. If the GIE bit is also set, the program will branch to the interrupt vector.
3. 4. 5. 6.
7.
8. 9.
Set the SYNC and SPEN bits and clear the CSRC bit. If interrupts are desired, set the RCIE bit of the PIE1 register and the GIE and PEIE bits of the INTCON register. If 9-bit reception is desired, set the RX9 bit. Verify address detection is disabled by clearing the ADDEN bit of the RCSTA register. Set the CREN bit to enable reception. The RCIF bit of the PIR1 register will be set when reception is complete. An interrupt will be generated if the RCIE bit of the PIE1 register was set. If 9-bit mode is enabled, retrieve the Most Significant bit from the RX9D bit of the RCSTA register. Retrieve the 8 Least Significant bits from the receive FIFO by reading the RCREG register. If an overrun error occurs, clear the error by either clearing the CREN bit of the RCSTA register.
TABLE 16-9:
Name INTCON PIE1 PIR1 RCREG RCSTA TRISC TXSTA Legend:
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Bit 6 PEIE ADIE ADIF RX9 TRISC6 TX9 Bit 5 T0IE RCIE RCIF SREN TRISC5 TXEN Bit 4 INTE TXIE TXIF CREN TRISC4 SYNC Bit 3 RBIE SSPIE SSPIF ADDEN TRISC3 -- Bit 2 T0IF CCP1IE CCP1IF FERR TRISC2 BRGH Bit 1 INTF TMR2IE TMR2IF OERR TRISC1 TRMT Bit 0 RBIF TMR1IE TMR1IF RX9D TRISC0 TX9D Value on POR, BOR 0000 000x 0000 0000 0000 0000 0000 0000 0000 000X 1111 1111 0000 -010 Value on all other Resets 0000 000x 0000 0000 0000 0000 0000 0000 0000 000X 1111 1111 0000 -010
Bit 7 GIE TMR1GIE TMR1GIF SPEN TRISC7 CSRC
AUSART Receive Data Register
x = unknown, - = unimplemented read as `0'. Shaded cells are not used for Synchronous Slave Reception.
DS41417A-page 152
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
16.4 AUSART Operation During Sleep
16.4.2
The AUSART will remain active during Sleep only in the Synchronous Slave mode. All other modes require the system clock and therefore can not generate the necessary signals to run the Transmit or Receive Shift registers during Sleep. Synchronous Slave mode uses an externally generated clock to run the Transmit and Receive Shift registers.
SYNCHRONOUS TRANSMIT DURING SLEEP
To transmit during Sleep, all the following conditions must be met before entering Sleep mode: * RCSTA and TXSTA Control registers must be configured for Synchronous Slave Transmission (refer to Section 16.3.2.2 "Synchronous Slave Transmission Set-up:"). * The TXIF interrupt flag must be cleared by writing the output data to the TXREG, thereby filling the TSR and transmit buffer. * If interrupts are desired, set the TXIE bit of the PIE1 register and the PEIE bit of the INTCON register. Upon entering Sleep mode, the device will be ready to accept clocks on TX/CK pin and transmit data on the RX/DT pin. When the data word in the TSR has been completely clocked out by the external device, the pending byte in the TXREG will transfer to the TSR and the TXIF flag will be set, thereby waking the processor from Sleep. At this point, the TXREG is available to accept another character for transmission, which will clear the TXIF flag. Upon waking from Sleep, the instruction following the SLEEP instruction will be executed. If the Global Interrupt Enable (GIE) bit is also set then the Interrupt Service Routine at address 0004h will be called.
16.4.1
SYNCHRONOUS RECEIVE DURING SLEEP
To receive during Sleep, all the following conditions must be met before entering Sleep mode: * RCSTA and TXSTA Control registers must be configured for Synchronous Slave Reception (refer to Section 16.3.2.4 "Synchronous Slave Reception Set-up:"). * If interrupts are desired, set the RCIE bit of the PIE1 register and the PEIE bit of the INTCON register. * The RCIF interrupt flag must be cleared by reading RCREG to unload any pending characters in the receive buffer. Upon entering Sleep mode, the device will be ready to accept data and clocks on the RX/DT and TX/CK pins, respectively. When the data word has been completely clocked in by the external device, the RCIF interrupt flag bit of the PIR1 register will be set, thereby waking the processor from Sleep. Upon waking from Sleep, the instruction following the SLEEP instruction will be executed. If the Global Interrupt Enable (GIE) bit of the INTCON register is also set, then the Interrupt Service Routine at address 0004h will be called.
2010 Microchip Technology Inc.
DS41417A-page 153
PIC16F/LF722A/723A
NOTES:
DS41417A-page 154
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.0 SSP MODULE OVERVIEW
The Synchronous Serial Port (SSP) module is a serial interface useful for communicating with other peripherals or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can operate in one of two modes: * Serial Peripheral Interface (SPI) * Inter-Integrated Circuit (I2CTM) A typical SPI connection between microcontroller devices is shown in Figure 17-1. Addressing of more than one slave device is accomplished via multiple hardware slave select lines. External hardware and additional I/O pins must be used to support multiple slave select addressing. This prevents extra overhead in software for communication. For SPI communication, typically three pins are used: * Serial Data Out (SDO) * Serial Data In (SDI) * Serial Clock (SCK) Additionally, a fourth pin may be used when in a Slave mode of operation: * Slave Select (SS)
17.1
SPI Mode
The SPI mode allows 8 bits of data to be synchronously transmitted and received, simultaneously. The SSP module can be operated in one of two SPI modes: * Master mode * Slave mode SPI is a full-duplex protocol, with all communication being bidirectional and initiated by a master device. All clocking is provided by the master device and all bits are transmitted, MSb first. Care must be taken to ensure that all devices on the SPI bus are setup to allow all controllers to send and receive data at the same time.
FIGURE 17-1:
TYPICAL SPI MASTER/SLAVE CONNECTION
SPI Slave SSPM<3:0> = 010x SDO Serial Input Buffer (SSPBUF) SDI Serial Input Buffer (SSPBUF)
SPI Master SSPM<3:0> = 00xx
Shift Register (SSPSR) MSb LSb
SDI
SDO MSb SCK SS
Shift Register (SSPSR) LSb
SCK General I/O Processor 1
Serial Clock Slave Select (optional)
Processor 2
2010 Microchip Technology Inc.
DS41417A-page 155
PIC16F/LF722A/723A
FIGURE 17-2: SPI MODE BLOCK DIAGRAM
Internal Data Bus Read SSPBUF Reg Write
SSPSR Reg SDI bit 0 Shift Clock bit 7
SDO
RA5/SS
SS Control Enable
RA0/SS
SSSEL
2 Clock Select Edge Select 2 Edge Select SCK TRISx 4 SSPM<3:0> Prescaler 4, 16, 64 TMR2 Output FOSC
DS41417A-page 156
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.1.1 MASTER MODE 17.1.1.3 Master Mode Setup
In Master mode, data transfer can be initiated at any time because the master controls the SCK line. Master mode determines when the slave (Figure 17-1, Processor 2) transmits data via control of the SCK line. In Master mode, the data is transmitted/received as soon as the SSPBUF register is loaded with a byte value. If the master is only going to receive, SDO output could be disabled (programmed and used as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. When initializing SPI Master mode operation, several options need to be specified. This is accomplished by programming the appropriate control bits in the SSPCON and SSPSTAT registers. These control bits allow the following to be specified: * * * * * SCK as clock output Idle state of SCK (CKP bit) Data input sample phase (SMP bit) Output data on rising/falling edge of SCK (CKE bit) Clock bit rate
17.1.1.1
Master Mode Operation
The SSP consists of a transmit/receive shift register (SSPSR) and a buffer register (SSPBUF). The SSPSR register shifts the data in and out of the device, MSb first. The SSPBUF register holds the data that is written out of the master until the received data is ready. Once the eight bits of data have been received, the byte is moved to the SSPBUF register. The Buffer Full Status bit, BF of the SSPSTAT register, and the SSP Interrupt Flag bit, SSPIF of the PIR1 register, are then set. Any write to the SSPBUF register during transmission/ reception of data will be ignored and the Write Collision Detect bit, WCOL of the SSPCON register, will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. When the application software is expecting to receive valid data, the SSPBUF should be read before the next byte of data is written to the SSPBUF. The BF bit of the SSPSTAT register is set when SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. The SSP interrupt may be used to determine when the transmission/reception is complete and the SSPBUF must be read and/or written. If interrupts are not used, then software polling can be done to ensure that a write collision does not occur. Example 17-1 shows the loading of the SSPBUF (SSPSR) for data transmission. Note: The SSPSR is not directly readable or writable and can only be accessed by addressing the SSPBUF register.
In Master mode, the SPI clock rate (bit rate) is user selectable to be one of the following: * * * * FOSC/4 (or TCY) FOSC/16 (or 4 TCY) FOSC/64 (or 16 TCY) (Timer2 output)/2
This allows a maximum data rate of 5 Mbps (at FOSC = 20 MHz). Figure 17-3 shows the waveforms for Master mode. The clock polarity is selected by appropriately programming the CKP bit of the SSPCON register. When the CKE bit is set, the SDO data is valid before there is a clock edge on SCK. The sample time of the input data is shown based on the state of the SMP bit and can occur at the middle or end of the data output time. The time when the SSPBUF is loaded with the received data is shown.
17.1.1.4
Sleep in Master Mode
17.1.1.2
Enabling Master I/O
To enable the serial port, the SSPEN bit of the SSPCON register, must be set. To reset or reconfigure SPI mode, clear the SSPEN bit, re-initialize the SSPCON register and then set the SSPEN bit. If a Master mode of operation is selected in the SSPM bits of the SSPCON register, the SDI, SDO and SCK pins will be assigned as serial port pins. For these pins to function as serial port pins, they must have their corresponding data direction bits set or cleared in the associated TRIS register as follows: * SDI configured as input * SDO configured as output * SCK configured as output
In Master mode, all module clocks are halted and the transmission/reception will remain in their current state, paused, until the device wakes from Sleep. After the device wakes up from Sleep, the module will continue to transmit/receive data.
2010 Microchip Technology Inc.
DS41417A-page 157
PIC16F/LF722A/723A
FIGURE 17-3:
Write to SSPBUF SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) SDO (CKE = 0) SDO (CKE = 1) SDI (SMP = 0) Input Sample (SMP = 0) SDI (SMP = 1) Input Sample (SMP = 1) SSPIF SSPSR to SSPBUF bit 7 bit 0 bit 7 bit 7 bit 6 bit 6 bit 5 bit 5 bit 4 bit 4 bit 3 bit 3 bit 2 bit 2 bit 1 bit 1 bit 0 bit 0
SPI MASTER MODE WAVEFORM
4 Clock Modes
bit 7
bit 0
EXAMPLE 17-1:
LOOP BANKSEL BTFSS GOTO BANKSEL MOVF MOVWF MOVF MOVWF
LOADING THE SSPBUF (SSPSR) REGISTER
SSPSTAT SSPSTAT, BF LOOP SSPBUF SSPBUF, W RXDATA TXDATA, W SSPBUF ; ;Has data been received(transmit complete)? ;No ; ;WREG reg = contents of SSPBUF ;Save in user RAM, if data is meaningful ;W reg = contents of TXDATA ;New data to xmit
DS41417A-page 158
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.1.2 SLAVE MODE 17.1.2.2 Enabling Slave I/O
For any SPI device acting as a slave, the data is transmitted and received as external clock pulses appear on SCK pin. This external clock must meet the minimum high and low times as specified in the electrical specifications. To enable the serial port, the SSPEN bit of the SSPCON register must be set. If a Slave mode of operation is selected in the SSPM bits of the SSPCON register, the SDI, SDO and SCK pins will be assigned as serial port pins. For these pins to function as serial port pins, they must have their corresponding data direction bits set or cleared in the associated TRIS register as follows: * SDI configured as input * SDO configured as output * SCK configured as input Optionally, a fourth pin, Slave Select (SS) may be used in Slave mode. Slave Select may be configured to operate on one of the following pins via the SSSEL bit in the APFCON register. * RA5/AN4/SS * RA0/AN0/SS Upon selection of a Slave Select pin, the appropriate bits must be set in the ANSELA and TRISA registers. Slave Select must be set as an input by setting the corresponding bit in TRISA, and digital I/O must be enabled on the SS pin by clearing the corresponding bit of the ANSELA register.
17.1.2.1
Slave Mode Operation
The SSP consists of a transmit/receive shift register (SSPSR) and a buffer register (SSPBUF). The SSPSR shifts the data in and out of the device, MSb first. The SSPBUF holds the data that was written to the SSPSR until the received data is ready. The slave has no control as to when data will be clocked in or out of the device. All data that is to be transmitted, to a master or another slave, must be loaded into the SSPBUF register before the first clock pulse is received. Once eight bits of data have been received: * Received byte is moved to the SSPBUF register * BF bit of the SSPSTAT register is set * SSPIF bit of the PIR1 register is set Any write to the SSPBUF register during transmission/ reception of data will be ignored and the Write Collision Detect bit, WCOL of the SSPCON register, will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. The user's firmware must read SSPBUF, clearing the BF flag, or the SSPOV bit of the SSPCON register will be set with the reception of the next byte and communication will be disabled. A SPI module transmits and receives at the same time, occasionally causing dummy data to be transmitted/ received. It is up to the user to determine which data is to be used and what can be discarded.
17.1.2.3
Slave Mode Setup
When initializing the SSP module to SPI Slave mode, compatibility must be ensured with the master device. This is done by programming the appropriate control bits of the SSPCON and SSPSTAT registers. These control bits allow the following to be specified: * * * * SCK as clock input Idle state of SCK (CKP bit) Data input sample phase (SMP bit) Output data on rising/falling edge of SCK (CKE bit)
Figure 17-4 and Figure 17-5 show example waveforms of Slave mode operation.
2010 Microchip Technology Inc.
DS41417A-page 159
PIC16F/LF722A/723A
FIGURE 17-4:
SS Optional SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPBUF SDO SDI (SMP = 0) Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0)
bit 7
bit 0
FIGURE 17-5:
SS Not Optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSPBUF SDO SDI (SMP = 0) Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF
SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 7
bit 0
DS41417A-page 160
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.1.2.4 Slave Select Operation
The SS pin allows Synchronous Slave mode operation. The SPI must be in Slave mode with SS pin control enabled (SSPM<3:0> = 0100). The associated TRIS bit for the SS pin must be set, making SS an input. In Slave Select mode, when: * SS = 0, The device operates as specified in Section 17.1.2 "Slave Mode". * SS = 1, The SPI module is held in Reset and the SDO pin will be tri-stated. Note 1: When the SPI is in Slave mode with SS pin control enabled (SSPM<3:0> = 0100), the SPI module will reset if the SS pin is driven high. 2: If the SPI is used in Slave mode with CKE set, the SS pin control must be enabled. When the SPI module resets, the bit counter is cleared to `0'. This can be done by either forcing the SS pin to a high level or clearing the SSPEN bit. Figure 17-6 shows the timing waveform for such a synchronization event. Note: SSPSR must be reinitialized by writing to the SSPBUF register before the data can be clocked out of the slave again.
17.1.2.5
Sleep in Slave Mode
While in Sleep mode, the slave can transmit/receive data. The SPI Transmit/Receive Shift register operates asynchronously to the device on the externally supplied clock source. This allows the device to be placed in Sleep mode and data to be shifted into the SPI Transmit/Receive Shift register. When all 8 bits have been received, the SSP Interrupt Flag bit will be set and if enabled, will wake the device from Sleep.
FIGURE 17-6:
SS
SLAVE SELECT SYNCHRONIZATION WAVEFORM
SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0)
Write to SSPBUF
SSPSR must be reinitialized by writing to the SSPBUF register before the data can be clocked out of the slave again.
SDO
bit 7
bit 6
bit 7
bit 0
SDI (SMP = 0) Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF
bit 0 bit 7 bit 7
2010 Microchip Technology Inc.
DS41417A-page 161
PIC16F/LF722A/723A
REGISTER 17-1:
R/W-0 WCOL bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
SSPCON: SYNC SERIAL PORT CONTROL REGISTER (SPI MODE)
R/W-0 R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 R/W-0 SSPM0 bit 0
SSPOV
WCOL: Write Collision Detect bit 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow SSPEN: Synchronous Serial Port Enable bit 1 = Enables serial port and configures SCK, SDO and SDI as serial port pins(1) 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level SSPM<3:0>: Synchronous Serial Port Mode Select bits 0000 = SPI Master mode, clock = FOSC/4 0001 = SPI Master mode, clock = FOSC/16 0010 = SPI Master mode, clock = FOSC/64 0011 = SPI Master mode, clock = TMR2 output/2 0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin. When enabled, these pins must be properly configured as input or output.
bit 6
bit 5
bit 4
bit 3-0
Note 1:
DS41417A-page 162
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 17-2:
R/W-0 SMP bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (SPI MODE)
R/W-0 CKE R-0 D/A R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0
SMP: SPI Data Input Sample Phase bit SPI Master mode: 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave mode: SMP must be cleared when SPI is used in Slave mode CKE: SPI Clock Edge Select bit SPI mode, CKP = 0: 1 = Data stable on rising edge of SCK 0 = Data stable on falling edge of SCK SPI mode, CKP = 1: 1 = Data stable on falling edge of SCK 0 = Data stable on rising edge of SCK D/A: Data/Address bit Used in I2C mode only. P: Stop bit Used in I2C mode only. S: Start bit Used in I2C mode only. R/W: Read/Write Information bit Used in I2C mode only. UA: Update Address bit Used in I2C mode only. BF: Buffer Full Status bit 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty
bit 6
bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
2010 Microchip Technology Inc.
DS41417A-page 163
PIC16F/LF722A/723A
TABLE 17-1:
Name ANSELA APFCON INTCON PIE1 PIR1 PR2 SSPBUF SSPCON SSPSTAT TRISA TRISC T2CON Legend: Bit 7 -- -- GIE TMR1GIE TMR1GIF
SUMMARY OF REGISTERS ASSOCIATED WITH SPI OPERATION
Bit 6 -- -- PEIE ADIE ADIF Bit 5 ANSA5 -- T0IE RCIE RCIF Bit 4 ANSA4 -- INTE TXIE TXIF Bit 3 ANSA3 -- RBIE SSPIE SSPIF Bit 2 ANSA2 -- T0IF CCP1IE CCP1IF Bit 1 ANSA1 SSSEL INTF TMR2IE TMR2IF Bit 0 ANSA0 CCP2SEL RBIF TMR1IE TMR1IF Value on POR, BOR --11 1111 ---- --00 0000 000x 0000 0000 0000 0000 1111 1111 xxxx xxxx SSPM2 R/W TRISA2 TRISC2 TMR2ON SSPM1 UA TRISA1 TRISC1 T2CKPS1 SSPM0 BF TRISA0 TRISC0 T2CKPS0 0000 0000 0000 0000 1111 1111 1111 1111 -000 0000 SSPEN D/A TRISA5 TRISC5 TOUTPS2 CKP P TRISA4 TRISC4 TOUTPS1 SSPM3 S TRISA3 TRISC3 TOUTPS0 Value on all other Resets --11 1111 ---- --00 0000 000x 0000 0000 0000 0000 1111 1111 uuuu uuuu 0000 0000 0000 0000 1111 1111 1111 1111 -000 0000
Timer2 Period Register Synchronous Serial Port Receive Buffer/Transmit Register WCOL SMP TRISA7 TRISC7 -- SSPOV CKE TRISA6 TRISC6 TOUTPS3
x = unknown, u = unchanged, - = unimplemented, read as `0'. Shaded cells are not used by the SSP in SPI mode.
DS41417A-page 164
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.2 I2C Mode
FIGURE 17-8:
The SSP module, in I2C mode, implements all slave functions, except general call support. It provides interrupts on Start and Stop bits in hardware to facilitate firmware implementations of the master functions. The SSP module implements the I2C Standard mode specifications: * * * I2C Slave mode (7-bit address) I2C Slave mode (10-bit address) Start and Stop bit interrupts enabled to support firmware Master mode * Address masking Two pins are used for data transfer; the SCL pin (clock line) and the SDA pin (data line). The user must configure the two pin's data direction bits as inputs in the appropriate TRIS register. Upon enabling I2C mode, the I2C slew rate limiters in the I/O pads are controlled by the SMP bit of SSPSTAT register. The SSP module functions are enabled by setting the SSPEN bit of SSPCON register. Data is sampled on the rising edge and shifted out on the falling edge of the clock. This ensures that the SDA signal is valid during the SCL high time. The SCL clock input must have minimum high and low times for proper operation. Refer to Section 23.0 "Electrical Specifications".
Master SDA SCL
TYPICAL I2CTM CONNECTIONS
VDD VDD
Slave 1 SDA SCL Slave 2 SDA SCL (optional)
The SSP module has six registers for I2C operation. They are: * * * * SSP Control (SSPCON) register SSP Status (SSPSTAT) register Serial Receive/Transmit Buffer (SSPBUF) register SSP Shift Register (SSPSR), not directly accessible * SSP Address (SSPADD) register * SSP Address Mask (SSPMSK) register
FIGURE 17-7:
I2CTM MODE BLOCK DIAGRAM
Internal Data Bus Read SSPBUF Reg Shift Clock SSPSR Reg Write
17.2.1
HARDWARE SETUP
SCL
Selection of I2C mode, with the SSPEN bit of the SSPCON register set, forces the SCL and SDA pins to be open drain, provided these pins are programmed as inputs by setting the appropriate TRISC bits. The SSP module will override the input state with the output data, when required, such as for Acknowledge and slave-transmitter sequences. Note: Pull-up resistors must be provided externally to the SCL and SDA pins for proper operation of the I2C module.
SDA
MSb
LSb SSPMSK Reg Match Detect SSPADD Reg Start and Stop bit Detect Addr Match
2010 Microchip Technology Inc.
DS41417A-page 165
PIC16F/LF722A/723A
17.2.2 START AND STOP CONDITIONS
During times of no data transfer (Idle time), both the clock line (SCL) and the data line (SDA) are pulled high through external pull-up resistors. The Start and Stop conditions determine the start and stop of data transmission. The Start condition is defined as a high-to-low transition of the SDA line while SCL is high. The Stop condition is defined as a low-to-high transition of the SDA line while SCL is high. Figure 17-9 shows the Start and Stop conditions. A master device generates these conditions for starting and terminating data transfer. Due to the definition of the Start and Stop conditions, when data is being transmitted, the SDA line can only change state when the SCL line is low.
FIGURE 17-9:
START AND STOP CONDITIONS
SDA
SCL S Change of Start Condition Data Allowed Change of Data Allowed Stop Condition P
17.2.3
ACKNOWLEDGE
After the valid reception of an address or data byte, the hardware automatically will generate the Acknowledge (ACK) pulse and load the SSPBUF register with the received value currently in the SSPSR register. There are certain conditions that will cause the SSP module not to generate this ACK pulse. They include any or all of the following: * The Buffer Full bit, BF of the SSPSTAT register, was set before the transfer was received. * The SSP Overflow bit, SSPOV of the SSPCON register, was set before the transfer was received. * The SSP module is being operated in Firmware Master mode.
In such a case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF of the PIR1 register is set. Table 17-2 shows the results of when a data transfer byte is received, given the status of bits BF and SSPOV. Flag bit BF is cleared by reading the SSPBUF register, while bit SSPOV is cleared through software.
TABLE 17-2:
DATA TRANSFER RECEIVED BYTE ACTIONS
SSPSR SSPBUF Generate ACK Pulse Set bit SSPIF (SSP Interrupt occurs if enabled)
Status Bits as Data Transfer is Received BF 0 1 1 0 Note 1: SSPOV
0 Yes Yes Yes 0 No No Yes 1 No No Yes 1 No No Yes Shaded cells show the conditions where the user software did not properly clear the overflow condition.
DS41417A-page 166
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.2.4 ADDRESSING 17.2.4.2 10-bit Addressing
Once the SSP module has been enabled, it waits for a Start condition to occur. Following the Start condition, the 8 bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock line (SCL). In 10-bit Address mode, two address bytes need to be received by the slave (Figure 17-11). The five Most Significant bits (MSbs) of the first address byte specify if it is a 10-bit address. The R/W bit of the SSPSTAT register must specify a write so the slave device will receive the second address byte. For a 10-bit address, the first byte would equal `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for 10-bit address is as follows for reception: 1. 2. 3. 4. 5. Load SSPADD register with high byte of address. Receive first (high) byte of address (bits SSPIF, BF and UA of the SSPSTAT register are set). Read the SSPBUF register (clears bit BF). Clear the SSPIF flag bit. Update the SSPADD register with second (low) byte of address (clears UA bit and releases the SCL line). Receive low byte of address (bits SSPIF, BF and UA are set). Update the SSPADD register with the high byte of address. If match releases SCL line, this will clear bit UA. Read the SSPBUF register (clears bit BF). Clear flag bit SSPIF.
17.2.4.1
7-bit Addressing
In 7-bit Addressing mode (Figure 17-10), the value of register SSPSR<7:1> is compared to the value of register SSPADD<7:1>. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: * The SSPSR register value is loaded into the SSPBUF register. * The BF bit is set. * An ACK pulse is generated. * SSP interrupt flag bit, SSPIF of the PIR1 register, is set (interrupt is generated if enabled) on the falling edge of the ninth SCL pulse.
6. 7.
8. 9.
If data is requested by the master, once the slave has been addressed: 1. 2. 3. 4. 5. Receive repeated Start condition. Receive repeat of high byte address with R/W = 1, indicating a read. BF bit is set and the CKP bit is cleared, stopping SCL and indicating a read request. SSPBUF is written, setting BF, with the data to send to the master device. CKP is set in software, releasing the SCL line.
17.2.4.3
Address Masking
The Address Masking register (SSPMSK) is only accessible while the SSPM bits of the SSPCON register are set to `1001'. In this register, the user can select which bits of a received address the hardware will compare when determining an address match. Any bit that is set to a zero in the SSPMSK register, the corresponding bit in the received address byte and SSPADD register are ignored when determining an address match. By default, the register is set to all ones, requiring a complete match of a 7-bit address or the lower eight bits of a 10-bit address.
2010 Microchip Technology Inc.
DS41417A-page 167
PIC16F/LF722A/723A
17.2.5 RECEPTION
When the R/W bit of the received address byte is clear, the master will write data to the slave. If an address match occurs, the received address is loaded into the SSPBUF register. An address byte overflow will occur if that loaded address is not read from the SSPBUF before the next complete byte is received. An SSP interrupt is generated for each data transfer byte. The BF, R/W and D/A bits of the SSPSTAT register are used to determine the status of the last received byte.
FIGURE 17-10:
I2CTM WAVEFORMS FOR RECEPTION (7-BIT ADDRESS)
R/W = 0 ACK Receiving Data D7 D6 D5 D4 D3 D2 D1 D0 8 9 1 2 3 4 5 6 7 8 9 ACK Receiving Data ACK D7 D6 D5 D4 D3 D2 D1 D0 1 2 3 4 5 6 7 8 9 P Bus Master sends Stop condition
Receiving Address SDA SCL SSPIF S A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7
Cleared in software
BF
SSPBUF register is read
SSPOV Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent.
DS41417A-page 168
2010 Microchip Technology Inc.
FIGURE 17-11:
Receive First Byte of Address Receive Second Byte of Address ACK A7 A0 D7 D6 A6 A3 A2 A1 D3 D5 D4 A5 A4 D5 D4 D2 D1 D0 D7 D6 Receive Data Byte ACK Receive Data Byte D3 D2 A9 R/W ACK A8 0
2010 Microchip Technology Inc.
Clock is held low until update of SSPADD has taken place Clock is held low until update of SSPADD has taken place ACK D1 D0 6 4 1 5 6 7 1 2 3 4 5 6 7 8 7 1 2 3 2 8 9 8 9 9 3 4 5 6 7 8 9 P Bus master sends Stop condition Cleared in software Cleared in software Cleared in software Dummy read of SSPBUF to clear BF flag SSPOV is set because SSPBUF is still full. ACK is not sent. Cleared by hardware when SSPADD is updated with low byte of address UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated with high byte of address
SDA
1
1
1
1
0
SCL
S
1
2
3
4
5
SSPIF
Cleared in software
BF
SSPBUF is written with contents of SSPSR
SSPOV
UA
I2CTM SLAVE MODE TIMING (RECEPTION, 10-BIT ADDRESS)
UA is set indicating that the SSPADD needs to be updated
CKP
PIC16F/LF722A/723A
DS41417A-page 169
PIC16F/LF722A/723A
17.2.6 TRANSMISSION
When the R/W bit of the received address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set and the slave will respond to the master by reading out data. After the address match, an ACK pulse is generated by the slave hardware and the SCL pin is held low (clock is automatically stretched) until the slave is ready to respond. See Section 17.2.7 "Clock Stretching". The data the slave will transmit must be loaded into the SSPBUF register, which sets the BF bit. The SCL line is released by setting the CKP bit of the SSPCON register. An SSP interrupt is generated for each transferred data byte. The SSPIF flag bit of the PIR1 register initiates an SSP interrupt, and must be cleared by software before the next byte is transmitted. The BF bit of the SSPSTAT register is cleared on the falling edge of the 8th received clock pulse. The SSPIF flag bit is set on the falling edge of the ninth clock pulse. Following the 8th falling clock edge, control of the SDA line is released back to the master so that the master can acknowledge or not acknowledge the response. If the master sends a not acknowledge, the slave's transmission is complete and the slave must monitor for the next Start condition. If the master acknowledges, control of the bus is returned to the slave to transmit another byte of data. Just as with the previous byte, the clock is stretched by the slave, data must be loaded into the SSPBUF and CKP must be set to release the clock line (SCL).
FIGURE 17-12:
I 2C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
Receiving Address R/W A1 ACK D7 D6 D5 D4 Transmitting Data D3 D2 D1 D0 ACK
SDA
A7
A6
A5
A4
A3
A2
SCL
S
1 2 Data in sampled
3
4
5
6
7
8
9
1 SCL held low while CPU responds to SSPIF
2
3
4
5
6
7
8
9
P
SSPIF BF
Dummy read of SSPBUF to clear BF flag
Cleared in software
SSPBUF is written in software
From SSP Interrupt Service Routine
CKP Set bit after writing to SSPBUF (the SSPBUF must be written to before the CKP bit can be set)
DS41417A-page 170
2010 Microchip Technology Inc.
FIGURE 17-13:
Bus Master sends Stop condition Clock is held low until CKP is set to `1' Receive First Byte of Address R/W = 1 ACK ACK 1 1 1 1 0 A9 A8 Transmitting Data Byte D7 D6 D5 D4 D3 D2 D1 D0 ACK
2010 Microchip Technology Inc.
Clock is held low until update of SSPADD has taken place R/W = 0 Receive Second Byte of Address ACK A7 A6 A5 A4 A3 A2 A1 A0 Clock is held low until update of SSPADD has taken place Bus Master sends Restarts condition 1 0 A9 A8 4 Sr 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P Cleared in software Cleared in software Cleared in software Dummy read of SSPBUF to clear BF flag Dummy read of SSPBUF to clear BF flag Write of SSPBUF Dummy read of SSPBUF to clear BF flag Completion of data transmission clears BF flag Cleared by hardware when SSPADD is updated with low byte of address. UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated with high byte of address. CKP is set in software, initiates transmission CKP is automatically cleared in hardware holding SCL low
Receive First Byte of Address
SDA
1
1
1
SCL
S
1
2
3
SSPIF
BF
SSPBUF is written with contents of SSPSR
UA
UA is set indicating that the SSPADD needs to be updated
I2C SLAVE MODE TIMING (TRANSMISSION 10-BIT ADDRESS)
CKP
PIC16F/LF722A/723A
DS41417A-page 171
PIC16F/LF722A/723A
17.2.7 CLOCK STRETCHING
2
During any SCL low phase, any device on the I C bus may hold the SCL line low and delay, or pause, the transmission of data. This "stretching" of a transmission allows devices to slow down communication on the bus. The SCL line must be constantly sampled by the master to ensure that all devices on the bus have released SCL for more data. Stretching usually occurs after an ACK bit of a transmission, delaying the first bit of the next byte. The SSP module hardware automatically stretches for two conditions: * After a 10-bit address byte is received (update SSPADD register) * Anytime the CKP bit of the SSPCON register is cleared by hardware The module will hold SCL low until the CKP bit is set. This allows the user slave software to update SSPBUF with data that may not be readily available. In 10-bit addressing modes, the SSPADD register must be updated after receiving the first and second address bytes. The SSP module will hold the SCL line low until the SSPADD has a byte written to it. The UA bit of the SSPSTAT register will be set, along with SSPIF, indicating an address update is needed.
Refer to Application Note AN554, "Software Implementation of I2CTM Bus Master" (DS00554) for more information.
17.2.9
MULTI-MASTER MODE
In Multi-Master mode, the interrupt generation on the detection of the Start and Stop conditions allow the determination of when the bus is free. The Stop (P) and Start (S) bits are cleared from a Reset or when the SSP module is disabled. The Stop (P) and Start (S) bits will toggle based on the Start and Stop conditions. Control of the I2C bus may be taken when the P bit of the SSPSTAT register is set or when the bus is Idle, and both the S and P bits are clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the Stop condition occurs. In Multi-Master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set TRIS bits). There are two stages where this arbitration of the bus can be lost. They are the address transfer and data transfer stages. When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed, an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at a later time. Refer to Application Note AN578, "Use of the SSP Module in the I2CTM Multi-Master Environment" (DS00578) for more information.
17.2.8
FIRMWARE MASTER MODE
Master mode of operation is supported in firmware using interrupt generation on the detection of the Start and Stop conditions. The Stop (P) and Start (S) bits of the SSPSTAT register are cleared from a Reset or when the SSP module is disabled (SSPEN cleared). The Stop (P) and Start (S) bits will toggle based on the Start and Stop conditions. Control of the I2C bus may be taken when the P bit is set or the bus is Idle and both the S and P bits are clear. In Firmware Master mode, the SCL and SDA lines are manipulated by setting/clearing the corresponding TRIS bit(s). The output level is always low, irrespective of the value(s) in the corresponding PORT register bit(s). When transmitting a `1', the TRIS bit must be set (input) and a `0', the TRIS bit must be clear (output). The following events will cause the SSP Interrupt Flag bit, SSPIF, to be set (SSP Interrupt will occur if enabled): * Start condition * Stop condition * Data transfer byte transmitted/received Firmware Master mode of operation can be done with either the Slave mode Idle (SSPM<3:0> = 1011), or with either of the Slave modes in which interrupts are enabled. When both master and slave functionality is enabled, the software needs to differentiate the source(s) of the interrupt.
DS41417A-page 172
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
17.2.10 CLOCK SYNCHRONIZATION 17.2.11 SLEEP OPERATION
When the CKP bit is cleared, the SCL output is held low once it is sampled low. Therefore, the CKP bit will not stretch the SCL line until an external I2C master device has already asserted the SCL line low. The SCL output will remain low until the CKP bit is set and all other devices on the I2C bus have released SCL. This ensures that a write to the CKP bit will not violate the minimum high time requirement for SCL (Figure 17-14). While in Sleep mode, the I2C module can receive addresses of data, and when an address match or complete byte transfer occurs, wake the processor from Sleep (if SSP interrupt is enabled).
FIGURE 17-14:
CLOCK SYNCHRONIZATION TIMING
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
SDA
DX
DX-1
SCL
CKP
Master device asserts clock Master device deasserts clock
WR SSPCON
2010 Microchip Technology Inc.
DS41417A-page 173
PIC16F/LF722A/723A
REGISTER 17-3:
R/W-0 WCOL bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
SSPCON: SYNCHRONOUS SERIAL PORT CONTROL REGISTER (I2C MODE)
R/W-0 R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 R/W-0 SSPM0 bit 0
SSPOV
WCOL: Write Collision Detect bit 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don't care" in Transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow SSPEN: Synchronous Serial Port Enable bit 1 = Enables the serial port and configures the SDA and SCL pins as serial port pins(2) 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit 1 = Release control of SCL 0 = Holds clock low (clock stretch). (Used to ensure data setup time.) SSPM<3:0>: Synchronous Serial Port Mode Select bits 0110 = I2C Slave mode, 7-bit address 0111 = I2C Slave mode, 10-bit address 1000 = Reserved 1001 = Load SSPMSK register at SSPADD SFR Address(1) 1010 = Reserved 1011 = I2C Firmware Controlled Master mode (Slave Idle) 1100 = Reserved 1101 = Reserved 1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled 1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled 2: When enabled, these pins must be properly configured as input or output using the associated TRIS bit.
bit 6
bit 5
bit 4
bit 3-0
Note 1: When this mode is selected, any reads or writes to the SSPADD SFR address accesses the SSPMSK register.
DS41417A-page 174
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 17-4:
R/W-0 SMP bit 7 Legend: R = Readable bit -n = Value at POR bit 7 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
SSPSTAT: SYNCHRONOUS SERIAL PORT STATUS REGISTER (I2C MODE)
R/W-0 CKE R-0 D/A R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0
SMP: SPI Data Input Sample Phase bit 1 = Slew Rate Control (limiting) disabled. Operating in I2C Standard mode (100 kHz and 1 MHz). 0 = Slew Rate Control (limiting) enabled. Operating in I2C Fast mode (400 kHz). CKE: SPI Clock Edge Select bit This bit must be maintained clear. Used in SPI mode only. D/A: DATA/ADDRESS bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address P: Stop bit This bit is cleared when the SSP module is disabled, or when the Start bit is detected last. 1 = Indicates that a Stop bit has been detected last (this bit is `0' on Reset) 0 = Stop bit was not detected last S: Start bit This bit is cleared when the SSP module is disabled, or when the Stop bit is detected last. 1 = Indicates that a Start bit has been detected last (this bit is `0' on Reset) 0 = Start bit was not detected last R/W: READ/WRITE bit Information This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next Start bit, Stop bit or ACK bit. 1 = Read 0 = Write UA: Update Address bit (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated BF: Buffer Full Status bit Receive: 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit: 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty
bit 6 bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2010 Microchip Technology Inc.
DS41417A-page 175
PIC16F/LF722A/723A
REGISTER 17-5:
R/W-1 MSK7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-1 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
SSPMSK: SSP MASK REGISTER
R/W-1 MSK6 R/W-1 MSK5 R/W-1 MSK4 R/W-1 MSK3 R/W-1 MSK2 R/W-1 MSK1 R/W-1 MSK0 bit 0
MSK<7:1>: Mask bits 1 = The received address bit n is compared to SSPADD to detect I2C address match 0 = The received address bit n is not used to detect I2C address match MSK<0>: Mask bit for I2C Slave Mode, 10-bit Address I2C Slave Mode, 10-bit Address (SSPM<3:0> = 0111): 1 = The received address bit `0' is compared to SSPADD<0> to detect I2C address match 0 = The received address bit `0' is not used to detect I2C address match All other SSP modes: this bit has no effect.
bit 0
REGISTER 17-6:
R/W-0 ADD7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
SSPADD: SSP I2C ADDRESS REGISTER
R/W-0 ADD6 R/W-0 ADD5 R/W-0 ADD4 R/W-0 ADD3 R/W-0 ADD2 R/W-0 ADD1 R/W-0 ADD0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
ADD<7:0>: Address bits Received address
TABLE 17-7:
Name INTCON PIR1 PIE1 SSPBUF SSPADD SSPCON SSPMSK(2) SSPSTAT TRISC Legend: Note 1: 2:
REGISTERS ASSOCIATED WITH I2C OPERATION
Bit 7 GIE Bit 6 PEIE ADIF ADIE Bit 5 T0IE RCIF RCIE Bit 4 INTE TXIF TXIE Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF TMR2IF TMR2IE Bit 0 RBIF TMR1IF TMR1IE Value on POR, BOR 0000 000x 0000 0000 0000 0000 xxxx xxxx 0000 0000 SSPM2 R/W TRISC2 SSPM1 UA TRISC1 SSPM0 BF TRISC0 0000 0000 1111 1111 0000 0000 1111 1111 Value on all other Resets 0000 000u 0000 0000 0000 0000 uuuu uuuu 0000 0000 0000 0000 1111 1111 0000 0000 1111 1111
TMR1GIF TMR1GIE
Synchronous Serial Port Receive Buffer/Transmit Register Synchronous Serial Port (I2C mode) Address Register WCOL SMP
(1)
SSPOV CKE
(1)
SSPEN D/A TRISC5
CKP P
SSPM3 S
Synchronous Serial Port (I2C mode) Address Mask Register TRISC7 TRISC6 TRISC4 TRISC3
x = unknown, u = unchanged, - = unimplemented locations read as `0'. Shaded cells are not used by SSP module in I2C mode. Maintain these bits clear in I2C mode. Accessible only when SSPM<3:0> = 1001.
DS41417A-page 176
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
18.0 PROGRAM MEMORY READ
The Flash program memory is readable during normal operation over the full VDD range of the device. To read data from program memory, five Special Function Registers (SFRs) are used: * * * * * PMCON1 PMDATL PMDATH PMADRL PMADRH The value written to the PMADRH:PMADRL register pair determines which program memory location is read. The read operation will be initiated by setting the RD bit of the PMCON1 register. The program memory Flash controller takes two instructions to complete the read. As a consequence, after the RD bit has been set, the next two instructions will be ignored. To avoid conflict with program execution, it is recommended that the two instructions following the setting of the RD bit are NOP. When the read completes, the result is placed in the PMDATLH:PMDATL register pair. Refer to Example 18-1 for sample code. Note: Code-protect does not effect the CPU from performing a read operation on the program memory. For more information, refer to Section 8.2 "Code Protection"
EXAMPLE 18-1:
BANKSEL MOVF MOVWF MOVF MOVWF BANKSEL BSF NOP NOP
PROGRAM MEMORY READ
PMADRL ; MS_PROG_ADDR, W; PMADRH ;MS Byte of Program Address to read LS_PROG_ADDR, W; PMADRL ;LS Byte of Program Address to read PMCON1 ; PMCON1, RD;Initiate Read
Required Sequence
;Any instructions here are ignored as program ;memory is read in second cycle after BSF BANKSEL PMDATL ; MOVF PMDATL, W;W = LS Byte of Program Memory Read MOVWF LOWPMBYTE; MOVF PMDATH, W;W = MS Byte of Program Memory Read MOVWF HIGHPMBYTE;
2010 Microchip Technology Inc.
DS41417A-page 177
PIC16F/LF722A/723A
REGISTER 18-1:
R-1 Reserved bit 7 Legend: R = Readable bit -n = Value at POR bit 7 bit 6-1 bit 0 W = Writable bit `1' = Bit is set S = Setable bit, cleared in hardware U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
PMCON1: PROGRAM MEMORY CONTROL 1 REGISTER
U-0 -- U-0 --l U-0 -- U-0 -- U-0 -- U-0 -- R/S-0 RD bit 0
Reserved: Read as `1'. Maintain this bit set. Unimplemented: Read as `0' RD: Read Control bit 1 = Initiates an program memory read (The RD is cleared in hardware; the RD bit can only be set (not cleared) in software). 0 = Does not initiate a program memory read
REGISTER 18-2:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 bit 5-0
PMDATH: PROGRAM MEMORY DATA HIGH REGISTER
U-0 -- R/W-x PMD13 R/W-x PMD12 R/W-x PMD11 R/W-x PMD10 R/W-x PMD9 R/W-x PMD8 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
Unimplemented: Read as `0' PMD<13:8>: The value of the program memory word pointed to by PMADRH and PMADRL after a program memory read command.
REGISTER 18-3:
R/W-x PMD7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
PMDATL: PROGRAM MEMORY DATA LOW REGISTER
R/W-x PMD6 R/W-x PMD5 R/W-x PMD4 R/W-x PMD3 R/W-x PMD2 R/W-x PMD1 R/W-x PMD0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
PMD<7:0>: The value of the program memory word pointed to by PMADRH and PMADRL after a program memory read command.
DS41417A-page 178
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
REGISTER 18-4:
U-0 -- bit 7 Legend: R = Readable bit -n = Value at POR bit 7-5 bit 4-0 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
PMADRH: PROGRAM MEMORY ADDRESS HIGH REGISTER
U-0 -- U-0 -- R/W-x PMA12 R/W-x PMA11 R/W-x PMA10 R/W-x PMA9 R/W-x PMA8 bit 0
Unimplemented: Read as `0' PMA<12:8>: Program Memory Read Address bits
REGISTER 18-5:
R/W-x PMA7 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-0
PMADRL: PROGRAM MEMORY ADDRESS LOW REGISTER
R/W-x PMA6 R/W-x PMA5 R/W-x PMA4 R/W-x PMA3 R/W-x PMA2 R/W-x PMA1 R/W-x PMA0 bit 0
W = Writable bit `1' = Bit is set
U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown
PMA<7:0>: Program Memory Read Address bits
TABLE 18-1:
Name PMCON1 PMADRH PMADRL PMDATH PMDATL Legend:
SUMMARY OF REGISTERS ASSOCIATED WITH PROGRAM MEMORY READ
Bit 6 -- -- -- Bit 5 -- -- Bit 4 -- Bit 3 -- Bit 2 -- Bit 1 -- Bit 0 RD Value on POR, BOR 1--- ---0 ---x xxxx xxxx xxxx --xx xxxx xxxx xxxx Value on all other Resets 1--- ---0 ---x xxxx xxxx xxxx --xx xxxx xxxx xxxx
Bit 7 Reserved -- --
Program Memory Read Address Register High Byte
Program Memory Read Address Register Low Byte Program Memory Read Data Register High Byte Program Memory Read Data Register Low Byte
x = unknown, u = unchanged, - = unimplemented, read as `0'. Shaded cells are not used by the Program Memory Read.
2010 Microchip Technology Inc.
DS41417A-page 179
PIC16F/LF722A/723A
NOTES:
DS41417A-page 180
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
19.0 POWER-DOWN MODE (SLEEP)
The Power-down mode is entered by executing a SLEEP instruction. If the Watchdog Timer is enabled: * * * * * * WDT will be cleared but keeps running. PD bit of the STATUS register is cleared. TO bit of the STATUS register is set. Oscillator driver is turned off. Timer1 oscillator is unaffected I/O ports maintain the status they had before SLEEP was executed (driving high, low or highimpedance). The following peripheral interrupts can wake the device from Sleep: 1. 2. 3. 4. 5. 6. 7. TMR1 Interrupt. Timer1 must be operating as an asynchronous counter. USART Receive Interrupt (Synchronous Slave mode only) A/D conversion (when A/D clock source is RC) Interrupt-on-change External Interrupt from INT pin Capture event on CCP1 or CCP2 SSP Interrupt in SPI or I2C Slave mode
Other peripherals cannot generate interrupts since during Sleep, no on-chip clocks are present. When the SLEEP instruction is being executed, the next instruction (PC + 1) is prefetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction, then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. Note: If the global interrupts are disabled (GIE is cleared), but any interrupt source has both its interrupt enable bit and the corresponding interrupt flag bits set, the device will immediately wake-up from Sleep. The SLEEP instruction is completely executed.
For lowest current consumption in this mode, all I/O pins should be either at VDD or VSS, with no external circuitry drawing current from the I/O pin. I/O pins that are high-impedance inputs should be pulled high or low externally to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level when external MCLR is enabled. Note: A Reset generated by a WDT time-out does not drive MCLR pin low.
19.1
Wake-up from Sleep
The device can wake-up from Sleep through one of the following events: 1. 2. 3. External Reset input on MCLR pin. Watchdog Timer wake-up (if WDT was enabled). Interrupt from RB0/INT pin, PORTB change or a peripheral interrupt.
The WDT is cleared when the device wakes up from Sleep, regardless of the source of wake-up.
The first event will cause a device Reset. The two latter events are considered a continuation of program execution. The TO and PD bits in the STATUS register can be used to determine the cause of device Reset. The PD bit, which is set on power-up, is cleared when Sleep is invoked. TO bit is cleared if WDT wake-up occurred.
2010 Microchip Technology Inc.
DS41417A-page 181
PIC16F/LF722A/723A
19.2 Wake-up Using Interrupts
When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT prescaler and postscaler (if enabled) will not be cleared, the TO bit will not be set and the PD bit will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake-up from Sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT prescaler and postscaler (if enabled) will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction.
FIGURE 19-1:
OSC1(1) CLKOUT(4) INT pin INTF flag (INTCON reg.) GIE bit (INTCON reg.) Instruction Flow PC Instruction Fetched Instruction Executed Note 1: 2: 3: 4:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 TOST(2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Interrupt Latency (3) Processor in Sleep
PC Inst(PC) = Sleep Inst(PC - 1)
PC + 1 Inst(PC + 1) Sleep
PC + 2
PC + 2 Inst(PC + 2) Inst(PC + 1)
PC + 2
0004h Inst(0004h)
0005h Inst(0005h) Inst(0004h)
Dummy Cycle
Dummy Cycle
XT, HS or LP Oscillator mode assumed. TOST = 1024 TOSC (drawing not to scale). This delay does not apply to EC and RC Oscillator modes. GIE = 1 assumed. In this case after wake-up, the processor jumps to 0004h. If GIE = 0, execution will continue in-line. CLKOUT is not available in XT, HS, LP or EC Oscillator modes, but shown here for timing reference.
TABLE 19-1:
Name
IOCB INTCON PIE1 PIE2 PIR1 PIR2
SUMMARY OF REGISTERS ASSOCIATED WITH POWER-DOWN MODE
Bit 6
IOCB6 PEIE ADIE -- ADIF --
Bit 7
IOCB7 GIE TMR1GIE -- TMR1GIF --
Bit 5
IOCB5 T0IE RCIE -- RCIF --
Bit 4
IOCB4 INTE TXIE -- TXIF --
Bit 3
IOCB3 RBIE SSPIE -- SSPIF --
Bit 2
IOCB2 T0IF CCP1IE -- CCP1IF --
Bit 1
IOCB1 INTF TMR2IE -- TMR2IF --
Bit 0
IOCB0 RBIF TMR1IE CCP2IE TMR1IF CCP2IF
Value on POR, BOR
0000 0000 0000 0000 0000 0000 ---- ---0 0000 0000 ---- ---0
Value on all other Resets
0000 0000 0000 0000 0000 0000 ---- ---0 0000 0000 ---- ---0
Legend:
x = unknown, u = unchanged, - = unimplemented, read as `0'. Shaded cells are not used in Power-Down mode.
DS41417A-page 182
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
20.0 IN-CIRCUIT SERIAL PROGRAMMINGTM (ICSPTM)
The device is placed into Program/Verify mode by holding the ICSPCLK and ICSPDAT pins low then raising the voltage on MCLR/VPP from 0v to VPP. In Program/Verify mode the Program Memory, User IDs and the Configuration Words are programmed through serial communications. The ICSPDAT pin is a bidirectional I/O used for transferring the serial data and the ISCPCLK pin is the clock input. For more information on ICSPTM refer to the "PIC16F72X/PIC16LF72X Programming Specification" (DS41332). Note: The ICD 2 produces a VPP voltage greater than the maximum VPP specification of the PIC16F/LF722A/723A. When using this programmer, an external circuit, such as the AC164112 MPLAB ICD 2 VPP voltage limiter, is required to keep the VPP voltage within the device specifications.
ICSPTM programming allows customers to manufacture circuit boards with unprogrammed devices. Programming can be done after the assembly process allowing the device to be programmed with the most recent firmware or a custom firmware. Five pins are needed for ICSPTM programming: * ICSPCLK * ICSPDAT * MCLR/VPP * VDD * VSS
FIGURE 20-1:
TYPICAL CONNECTION FOR ICSPTM PROGRAMMING
External Programming Signals
VDD
Device to be Programmed
VDD 10k VPP GND Data Clock
VDD MCLR/VPP VSS ICSPDAT ICSPCLK
*
*
*
To Normal Connections
* Isolation devices (as required).
2010 Microchip Technology Inc.
DS41417A-page 183
PIC16F/LF722A/723A
NOTES:
DS41417A-page 184
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
21.0 INSTRUCTION SET SUMMARY
TABLE 21-1:
Field
f W b k x
The PIC16F/LF722A/723A instruction set is highly orthogonal and is comprised of three basic categories: * Byte-oriented operations * Bit-oriented operations * Literal and control operations Each PIC16 instruction is a 14-bit word divided into an opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The formats for each of the categories is presented in Figure 21-1, while the various opcode fields are summarized in Table 21-1. Table 21-2 lists the instructions recognized by the MPASMTM assembler. For byte-oriented instructions, `f' represents a file register designator and `d' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If `d' is zero, the result is placed in the W register. If `d' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, `b' represents a bit field designator, which selects the bit affected by the operation, while `f' represents the address of the file in which the bit is located. For literal and control operations, `k' represents an 8-bit or 11-bit constant, or literal value. One instruction cycle consists of four oscillator periods; for an oscillator frequency of 4 MHz, this gives a nominal instruction execution time of 1 s. All instructions are executed within a single instruction cycle, unless a conditional test is true, or the program counter is changed as a result of an instruction. When this occurs, the execution takes two instruction cycles, with the second cycle executed as a NOP. All instruction examples use the format `0xhh' to represent a hexadecimal number, where `h' signifies a hexadecimal digit.
OPCODE FIELD DESCRIPTIONS
Description
Register file address (0x00 to 0x7F) Working register (accumulator) Bit address within an 8-bit file register Literal field, constant data or label Don't care location (= 0 or 1). The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1. Program Counter Time-out bit Carry bit Digit carry bit Zero bit Power-down bit
d
PC TO C DC Z PD
FIGURE 21-1:
GENERAL FORMAT FOR INSTRUCTIONS
0
Byte-oriented file register operations 13 876 OPCODE d f (FILE #) d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 76 OPCODE b (BIT #) f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 OPCODE k = 8-bit immediate value CALL and GOTO instructions only 13 11 OPCODE 10 k (literal) 8 7 k (literal)
0
21.1
Read-Modify-Write Operations
0
Any instruction that specifies a file register as part of the instruction performs a Read-Modify-Write (R-M-W) operation. The register is read, the data is modified, and the result is stored according to either the instruction, or the destination designator `d'. A read operation is performed on a register even if the instruction writes to that register. For example, a CLRF PORTB instruction will read PORTB, clear all the data bits, then write the result back to PORTB. This example would have the unintended consequence of clearing the condition that set the RBIF flag.
0
k = 11-bit immediate value
2010 Microchip Technology Inc.
DS41417A-page 185
PIC16F/LF722A/723A
TABLE 21-2:
Mnemonic, Operands
PIC16F/LF722A/723A INSTRUCTION SET
Description Cycles 14-Bit Opcode MSb LSb Status Affected Notes
BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f - f, d f, d f, d f, d f, d f, d f, d f - f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0xxx dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff xxxx ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff C, DC, Z Z Z Z Z Z Z Z Z 1, 2 1, 2 2 1, 2 1, 2 1, 2, 3 1, 2 1, 2, 3 1, 2 1, 2
C C C, DC, Z Z
1, 2 1, 2 1, 2 1, 2 1, 2
BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW Note 1: f, b f, b f, b f, b k k k - k k k - k - - k k Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set Add literal and W AND literal with W Call Subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into Standby mode Subtract W from literal Exclusive OR literal with W 1 1 1 (2) 1 (2) 1 1 2 1 2 1 1 2 2 2 1 1 1 01 01 01 01 11 11 10 00 10 11 11 00 11 00 00 11 11 00bb 01bb 10bb 11bb 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 bfff bfff bfff bfff kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk ffff ffff ffff ffff kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk C, DC, Z Z TO, PD Z 1, 2 1, 2 3 3
LITERAL AND CONTROL OPERATIONS
TO, PD C, DC, Z Z
2: 3:
When an I/O register is modified as a function of itself (e.g., MOVF PORTA, 1), the value used will be that value present on the pins themselves. For example, if the data latch is `1' for a pin configured as input and is driven low by an external device, the data will be written back with a `0'. If this instruction is executed on the TMR0 register (and where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 module. If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP.
DS41417A-page 186
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
21.2
ADDLW Syntax: Operands: Operation: Status Affected: Description:
Instruction Descriptions
Add literal and W [ label ] ADDLW 0 k 255 (W) + k (W) C, DC, Z The contents of the W register are added to the eight-bit literal `k' and the result is placed in the W register. k BCF Syntax: Operands: Operation: Status Affected: Description: Bit Clear f [ label ] BCF 0 f 127 0b7 0 (f) None Bit `b' in register `f' is cleared. f,b
ADDWF Syntax: Operands: Operation: Status Affected: Description:
Add W and f [ label ] ADDWF 0 f 127 d 0,1 (W) + (f) (destination) C, DC, Z Add the contents of the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. f,d
BSF Syntax: Operands: Operation: Status Affected: Description:
Bit Set f [ label ] BSF 0 f 127 0b7 1 (f) None Bit `b' in register `f' is set. f,b
ANDLW Syntax: Operands: Operation: Status Affected: Description:
AND literal with W [ label ] ANDLW 0 k 255 (W) .AND. (k) (W) Z The contents of W register are AND'ed with the eight-bit literal `k'. The result is placed in the W register. k
BTFSC Syntax: Operands: Operation: Status Affected: Description:
Bit Test f, Skip if Clear [ label ] BTFSC f,b 0 f 127 0b7 skip if (f) = 0 None If bit `b' in register `f' is `1', the next instruction is executed. If bit `b', in register `f', is `0', the next instruction is discarded, and a NOP is executed instead, making this a 2-cycle instruction.
ANDWF Syntax: Operands: Operation: Status Affected: Description:
AND W with f [ label ] ANDWF 0 f 127 d 0,1 (W) .AND. (f) (destination) Z AND the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. f,d
2010 Microchip Technology Inc.
DS41417A-page 187
PIC16F/LF722A/723A
BTFSS Syntax: Operands: Operation: Status Affected: Description: Bit Test f, Skip if Set [ label ] BTFSS f,b 0 f 127 0b<7 skip if (f) = 1 None If bit `b' in register `f' is `0', the next instruction is executed. If bit `b' is `1', then the next instruction is discarded and a NOP is executed instead, making this a 2-cycle instruction. Status Affected: Description: CLRWDT Syntax: Operands: Operation: Clear Watchdog Timer [ label ] CLRWDT None 00h WDT 0 WDT prescaler, 1 TO 1 PD TO, PD CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set.
CALL Syntax: Operands: Operation:
Call Subroutine [ label ] CALL k 0 k 2047 (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> None Call Subroutine. First, return address (PC + 1) is pushed onto the stack. The eleven-bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two-cycle instruction.
COMF Syntax: Operands: Operation: Status Affected: Description:
Complement f [ label ] COMF 0 f 127 d [0,1] (f) (destination) Z The contents of register `f' are complemented. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f'. f,d
Status Affected: Description:
CLRF Syntax: Operands: Operation: Status Affected: Description:
Clear f [ label ] CLRF 0 f 127 00h (f) 1Z Z The contents of register `f' are cleared and the Z bit is set. f
DECF Syntax: Operands: Operation: Status Affected: Description:
Decrement f [ label ] DECF f,d 0 f 127 d [0,1] (f) - 1 (destination) Z Decrement register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'.
CLRW Syntax: Operands: Operation: Status Affected: Description:
Clear W [ label ] CLRW None 00h (W) 1Z Z W register is cleared. Zero bit (Z) is set.
DS41417A-page 188
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
DECFSZ Syntax: Operands: Operation: Status Affected: Description: Decrement f, Skip if 0 [ label ] DECFSZ f,d 0 f 127 d [0,1] (f) - 1 (destination); skip if result = 0 None The contents of register `f' are decremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. If the result is `1', the next instruction is executed. If the result is `0', then a NOP is executed instead, making it a 2-cycle instruction. INCFSZ Syntax: Operands: Operation: Status Affected: Description: Increment f, Skip if 0 [ label ] INCFSZ f,d 0 f 127 d [0,1] (f) + 1 (destination), skip if result = 0 None The contents of register `f' are incremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. If the result is `1', the next instruction is executed. If the result is `0', a NOP is executed instead, making it a 2-cycle instruction.
GOTO Syntax: Operands: Operation: Status Affected: Description:
Unconditional Branch [ label ] GOTO k 0 k 2047 k PC<10:0> PCLATH<4:3> PC<12:11> None GOTO is an unconditional branch. The eleven-bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two-cycle instruction.
IORLW Syntax: Operands: Operation: Status Affected: Description:
Inclusive OR literal with W [ label ] IORLW k 0 k 255 (W) .OR. k (W) Z The contents of the W register are OR'ed with the eight-bit literal `k'. The result is placed in the W register.
INCF Syntax: Operands: Operation: Status Affected: Description:
Increment f [ label ] INCF f,d 0 f 127 d [0,1] (f) + 1 (destination) Z The contents of register `f' are incremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'.
IORWF Syntax: Operands: Operation: Status Affected: Description:
Inclusive OR W with f [ label ] IORWF f,d 0 f 127 d [0,1] (W) .OR. (f) (destination) Z Inclusive OR the W register with register `f'. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'.
2010 Microchip Technology Inc.
DS41417A-page 189
PIC16F/LF722A/723A
MOVF Syntax: Operands: Operation: Status Affected: Description: Move f [ label ] MOVF f,d 0 f 127 d [0,1] (f) (dest) Z The contents of register f is moved to a destination dependent upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register since status flag Z is affected. 1 1
MOVF FSR, 0
MOVWF Syntax: Operands: Operation: Status Affected: Description: Words: Cycles: Example:
Move W to f [ label ] (W) (f) None Move data from W register to register `f'. 1 1 MOVW F OPTION MOVWF f 0 f 127
Words: Cycles: Example:
Before Instruction OPTION = W = After Instruction OPTION = W =
0xFF 0x4F 0x4F 0x4F
After Instruction W= value in FSR register Z=1
MOVLW Syntax: Operands: Operation: Status Affected: Description:
Move literal to W [ label ] k (W) None The eight-bit literal `k' is loaded into W register. The "don't cares" will assemble as `0's. 1 1
MOVLW 0x5A
NOP Syntax: Operands: Operation: Status Affected: Description: Words: Cycles: Example:
No Operation [ label ] None No operation None No operation. 1 1
NOP
MOVLW k
NOP
0 k 255
Words: Cycles: Example:
After Instruction W=
0x5A
DS41417A-page 190
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
RETFIE Syntax: Operands: Operation: Status Affected: Description: Return from Interrupt [ label ] None TOS PC, 1 GIE None Return from Interrupt. Stack is POPed and Top-of-Stack (TOS) is loaded in the PC. Interrupts are enabled by setting Global Interrupt Enable bit, GIE (INTCON<7>). This is a two-cycle instruction. 1 2
RETFIE
RETLW Syntax: Operands: Operation: Status Affected: Description:
Return with literal in W [ label ] RETLW k 0 k 255 k (W); TOS PC None The W register is loaded with the eight bit literal `k'. The program counter is loaded from the top of the stack (the return address). This is a two-cycle instruction. 1 2 CALL TABLE;W contains table
;offset value * ;W now has table value * * ADDWF PC ;W = offset RETLW k1 ;Begin table RETLW k2 ; * * * RETLW kn ; End of table
RETFIE
Words: Cycles: Example:
Words: Cycles: Example:
After Interrupt PC = GIE =
TABLE TOS 1
Before Instruction W = 0x07 After Instruction W = value of k8
RETURN Syntax: Operands: Operation: Status Affected: Description:
Return from Subroutine [ label ] None TOS PC None Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two-cycle instruction. RETURN
2010 Microchip Technology Inc.
DS41417A-page 191
PIC16F/LF722A/723A
RLF Syntax: Operands: Operation: Status Affected: Description: Rotate Left f through Carry [ label ] 0 f 127 d [0,1] See description below C The contents of register `f' are rotated one bit to the left through the Carry flag. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is stored back in register `f'.
C Register f
SLEEP Syntax: Operands: Operation:
Enter Sleep mode [ label ] SLEEP None 00h WDT, 0 WDT prescaler, 1 TO, 0 PD TO, PD The power-down Status bit, PD is cleared. Time-out Status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into Sleep mode with the oscillator stopped.
RLF
f,d
Status Affected: Description:
Words: Cycles: Example:
1 1
RLF REG1,0 REG1 C = = = = = 1110 0110 0 1110 0110 1100 1100 1
Before Instruction After Instruction
REG1 W C
RRF Syntax: Operands: Operation: Status Affected: Description:
Rotate Right f through Carry [ label ] RRF f,d 0 f 127 d [0,1] See description below C The contents of register `f' are rotated one bit to the right through the Carry flag. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'.
C Register f
SUBLW Syntax: Operands: Operation: Description:
Subtract W from literal [ label ] SUBLW k 0 k 255 k - (W) W) The W register is subtracted (2's complement method) from the eight-bit literal `k'. The result is placed in the W register. C=0 C=1 DC = 0 DC = 1 Wk Wk W<3:0> k<3:0> W<3:0> k<3:0>
Status Affected: C, DC, Z
DS41417A-page 192
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
SUBWF Syntax: Operands: Operation: Description: Subtract W from f [ label ] SUBWF f,d 0 f 127 d [0,1] (f) - (W) destination) Subtract (2's complement method) W register from register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f. C=0 C=1 DC = 0 DC = 1 Wf Wf W<3:0> f<3:0> W<3:0> f<3:0> XORLW Syntax: Operands: Operation: Status Affected: Description: Exclusive OR literal with W [ label ] XORLW k 0 k 255 (W) .XOR. k W) Z The contents of the W register are XOR'ed with the eight-bit literal `k'. The result is placed in the W register.
Status Affected: C, DC, Z
SWAPF Syntax: Operands: Operation: Status Affected: Description:
Swap Nibbles in f [ label ] SWAPF f,d 0 f 127 d [0,1] (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) None The upper and lower nibbles of register `f' are exchanged. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed in register `f'.
XORWF Syntax: Operands: Operation: Status Affected: Description:
Exclusive OR W with f [ label ] XORWF 0 f 127 d [0,1] (W) .XOR. (f) destination) Z Exclusive OR the contents of the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. f,d
2010 Microchip Technology Inc.
DS41417A-page 193
PIC16F/LF722A/723A
NOTES:
DS41417A-page 194
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
22.0 DEVELOPMENT SUPPORT
22.1
The PIC(R) microcontrollers and dsPIC(R) digital signal controllers are supported with a full range of software and hardware development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Compilers/Assemblers/Linkers - MPLAB C Compiler for Various Device Families - HI-TECH C for Various Device Families - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families * Simulators - MPLAB SIM Software Simulator * Emulators - MPLAB REAL ICETM In-Circuit Emulator * In-Circuit Debuggers - MPLAB ICD 3 - PICkitTM 3 Debug Express * Device Programmers - PICkitTM 2 Programmer - MPLAB PM3 Device Programmer * Low-Cost Demonstration/Development Boards, Evaluation Kits, and Starter Kits
MPLAB Integrated Development Environment Software
The MPLAB IDE software brings an ease of software development previously unseen in the 8/16/32-bit microcontroller market. The MPLAB IDE is a Windows(R) operating system-based application that contains: * A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - In-Circuit Emulator (sold separately) - In-Circuit Debugger (sold separately) * A full-featured editor with color-coded context * A multiple project manager * Customizable data windows with direct edit of contents * High-level source code debugging * Mouse over variable inspection * Drag and drop variables from source to watch windows * Extensive on-line help * Integration of select third party tools, such as IAR C Compilers The MPLAB IDE allows you to: * Edit your source files (either C or assembly) * One-touch compile or assemble, and download to emulator and simulator tools (automatically updates all project information) * Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power.
2010 Microchip Technology Inc.
DS41417A-page 195
PIC16F/LF722A/723A
22.2 MPLAB C Compilers for Various Device Families 22.5 MPLINK Object Linker/ MPLIB Object Librarian
The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip's PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger.
The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: * Efficient linking of single libraries instead of many smaller files * Enhanced code maintainability by grouping related modules together * Flexible creation of libraries with easy module listing, replacement, deletion and extraction
22.3
HI-TECH C for Various Device Families
The HI-TECH C Compiler code development systems are complete ANSI C compilers for Microchip's PIC family of microcontrollers and the dsPIC family of digital signal controllers. These compilers provide powerful integration capabilities, omniscient code generation and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple platforms.
22.6
MPLAB Assembler, Linker and Librarian for Various Device Families
22.4
MPASM Assembler
The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel(R) standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: * Integration into MPLAB IDE projects * User-defined macros to streamline assembly code * Conditional assembly for multi-purpose source files * Directives that allow complete control over the assembly process
MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: * * * * * * Support for the entire device instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility
DS41417A-page 196
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
22.7 MPLAB SIM Software Simulator 22.9
The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC(R) DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool.
MPLAB ICD 3 In-Circuit Debugger System
MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC(R) Flash microcontrollers and dsPIC(R) DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated Development Environment (IDE). The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers.
22.8
MPLAB REAL ICE In-Circuit Emulator System
22.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express
The MPLAB PICkit 3 allows debugging and programming of PIC(R) and dsPIC(R) Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial ProgrammingTM. The PICkit 3 Debug Express include the PICkit 3, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software.
MPLAB REAL ICE In-Circuit Emulator System is Microchip's next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC(R) Flash MCUs and dsPIC(R) Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The emulator is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables.
2010 Microchip Technology Inc.
DS41417A-page 197
PIC16F/LF722A/723A
22.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express
The PICkitTM 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip's Flash families of microcontrollers. The full featured Windows(R) programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip's powerful MPLAB Integrated Development Environment (IDE) the PICkitTM 2 enables in-circuit debugging on most PIC(R) microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. The PICkit 2 Debug Express include the PICkit 2, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software.
22.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits
A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEMTM and dsPICDEMTM demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ(R) security ICs, CAN, IrDA(R), PowerSmart battery management, SEEVAL(R) evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits.
22.12 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSPTM cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications.
DS41417A-page 198
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
23.0 ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings()
Ambient temperature under bias....................................................................................................... -40C to +125C Storage temperature ........................................................................................................................ -65C to +150C Voltage on VDD with respect to VSS, PIC16F722A/723A ................................................................... -0.3V to +6.5V Voltage on VCAP pin with respect to VSS, PIC16F722A/723A ............................................................ -0.3V to +4.0V Voltage on VDD with respect to VSS, PIC16LF722A/723A ................................................................. -0.3V to +4.0V Voltage on MCLR with respect to Vss ................................................................................................. -0.3V to +9.0V Voltage on all other pins with respect to VSS ........................................................................... -0.3V to (VDD + 0.3V) Total power dissipation(1) ............................................................................................................................... 800 mW Maximum current out of VSS pin ...................................................................................................................... 95 mA Maximum current into VDD pin ......................................................................................................................... 70 mA Clamp current, IK (VPIN < 0 or VPIN > VDD)20 mA Maximum output current sunk by any I/O pin.................................................................................................... 25 mA Maximum output current sourced by any I/O pin .............................................................................................. 25 mA Maximum current sunk by all ports(2), -40C TA +85C for industrial ........................................................ 200 mA Maximum current sunk by all ports(2), -40C TA +125C for extended........................................................ 90 mA Maximum current sourced by all ports(2), 40C TA +85C for industrial ................................................... 140 mA Maximum current sourced by all ports(2), -40C TA +125C for extended................................................... 65 mA Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOl x IOL). NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure above maximum rating conditions for extended periods may affect device reliability.
2010 Microchip Technology Inc.
DS41417A-page 199
PIC16F/LF722A/723A
23.1 DC Characteristics: PIC16F/LF722A/723A-I/E (Industrial, Extended)
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Characteristic Supply Voltage PIC16LF722A/723A 1.8 1.8 2.3 2.5 1.8 1.8 2.3 2.5 1.5 1.7 -- -- -- -5.5 -5.5 -5.5 -6 -6 -6 D004* * SVDD VDD Rise Rate to ensure internal Power-on Reset signal 0.05 -- -- -- -- -- -- -- -- -- -- 1.6 0.8 1.7 -- -- -- -- -- -- -- 3.6 3.6 3.6 3.6 5.5 5.5 5.5 5.5 -- -- -- -- -- 5.5 5.5 5.5 6 6 6 -- V V V V V V V V V V V V V % % % % % % V/ms Device in Sleep mode Device in Sleep mode VFVR = 1.024V, VDD 2.5V VFVR = 2.048V, VDD 2.5V VFVR = 4.096V, VDD 4.75V; -40 TA85C VFVR = 1.024V, VDD 2.5V VFVR = 2.048V, VDD 2.5V VFVR = 4.096V, VDD 4.75V; -40 TA125C See Section 3.2 "Power-on Reset (POR)" for details. FOSC 16 MHz: HFINTOSC, EC FOSC 4 MHz FOSC 20 MHz, EC FOSC 20 MHz, HS FOSC 16 MHz: HFINTOSC, EC FOSC 4 MHz FOSC 20 MHz, EC FOSC 20 MHz, HS Device in Sleep mode Device in Sleep mode Min. Typ Max. Units Conditions
PIC16LF722A/723A
PIC16F722A/723A Param. No. D001 Sym. VDD
D001
PIC16F722A/723A
D002* D002*
VDR
RAM Data Retention Voltage(1) PIC16LF722A/723A PIC16F722A/723A
VPOR* VPORR*
Power-on Reset Release Voltage Power-on Reset Rearm Voltage PIC16LF722A/723A PIC16F722A/723A
D003
VFVR
Fixed Voltage Reference Voltage, Initial Accuracy
These parameters are characterized but not tested. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.
DS41417A-page 200
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 23-1:
VDD VPOR VPORR
POR AND POR REARM WITH SLOW RISING VDD
VSS NPOR
POR REARM VSS TVLOW(2) Note 1: 2: 3: TPOR(3)
When NPOR is low, the device is held in Reset. TPOR 1 s typical. TVLOW 2.7 s typical.
2010 Microchip Technology Inc.
DS41417A-page 201
PIC16F/LF722A/723A
23.2 DC Characteristics: PIC16F/LF722A/723A-I/E (Industrial, Extended)
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min. Typ Max. Units Conditions VDD Note
PIC16LF722A/723A
PIC16F722A/723A Param No. Device Characteristics Supply Current (IDD)(1, 2) D009 LDO Regulator -- -- -- -- D010 -- -- D010 -- -- -- D011 -- -- D011 -- -- -- D011 D011 -- -- -- -- -- D012 D012 -- -- -- -- -- D013 D013 -- -- -- -- -- Note 1: 2:
350 50 30 5 7.0 9.0 11 14 15 7.0 9.0 11 14 15 110 150 120 180 240 230 400 250 420 500 125 230 150 225 250
-- -- -- -- 12 14 20 22 24 12 18 21 25 27 150 215 175 250 300 300 600 350 650 750 180 270 205 320 410
A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
-- -- -- -- 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0
HS, EC OR INTOSC/INTOSCIO (8-16 MHZ) Clock modes with all VCAP pins disabled All VCAP pins disabled VCAP enabled on RA0, RA5 or RA6 LP Clock mode and Sleep (requires FVR and BOR to be disabled) FOSC = 32 kHz LP Oscillator mode (Note 4), -40C TA +85C FOSC = 32 kHz LP Oscillator mode (Note 4), -40C TA +85C FOSC = 32 kHz LP Oscillator mode -40C TA +125C FOSC = 32 kHz LP Oscillator mode (Note 4) -40C TA +125C FOSC = 1 MHz XT Oscillator mode FOSC = 1 MHz XT Oscillator mode (Note 5)
FOSC = 4 MHz XT Oscillator mode FOSC = 4 MHz XT Oscillator mode (Note 5)
FOSC = 1 MHz EC Oscillator mode FOSC = 1 MHz EC Oscillator mode (Note 5)
3: 4: 5:
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled. The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended by the formula IR = VDD/2REXT (mA) with REXT in k FVR and BOR are disabled. 0.1 F capacitor on VCAP (RA0).
DS41417A-page 202
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
23.2 DC Characteristics: PIC16F/LF722A/723A-I/E (Industrial, Extended) (Continued)
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min. Typ Max. Units Conditions VDD Note PIC16LF722A/723A
PIC16F722A/723A Param No. Device Characteristics Supply Current (IDD)(1, 2) D014 D014 -- -- -- -- -- D015 D015 -- -- -- -- -- D016 D016 -- -- -- -- -- D017 D017 -- -- -- -- -- D018 D018 -- -- -- -- -- D019 D019 Note 1: 2: -- -- -- --
290 460 300 450 500 100 120 115 135 150 650 1000 625 1000 1100 1.0 1.5 1 1.5 1.7 210 340 225 360 410 1.6 2.0 1.6 1.9
330 500 430 655 730 130 150 195 200 220 800 1200 850 1200 1500 1.2 1.85 1.2 1.7 2.1 240 380 320 445 650 1.9 2.8 2 3.2
A A A A A A A A A A A A A A A mA mA mA mA mA A A A A A mA mA mA mA
1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 3.0 3.6 3.0 5.0
FOSC = 4 MHz EC Oscillator mode FOSC = 4 MHz EC Oscillator mode (Note 5)
FOSC = 500 kHz MFINTOSC mode FOSC = 500 kHz MFINTOSC mode (Note 5)
FOSC = 8 MHz HFINTOSC mode FOSC = 8 MHz HFINTOSC mode (Note 5)
FOSC = 16 MHz HFINTOSC mode FOSC = 16 MHz HFINTOSC mode (Note 5)
FOSC = 4 MHz EXTRC mode (Note 3, Note 5) FOSC = 4 MHz EXTRC mode (Note 3, Note 5)
FOSC = 20 MHz HS Oscillator mode FOSC = 20 MHz HS Oscillator mode (Note 5)
3: 4: 5:
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled. The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended by the formula IR = VDD/2REXT (mA) with REXT in k FVR and BOR are disabled. 0.1 F capacitor on VCAP (RA0).
2010 Microchip Technology Inc.
DS41417A-page 203
PIC16F/LF722A/723A
23.3 DC Characteristics: PIC16F/LF722A/723A-I/E (Power-Down)
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min. (IPD)(2) -- -- D020 -- -- -- D021 D021 -- -- -- -- -- D021A D021A -- -- -- -- -- D022 D022 -- -- -- -- -- D026 D026 -- -- -- -- -- Note 1: 0.02 0.08 4.3 5 5.5 0.5 0.8 6 6.5 7.5 8.5 8.5 23 25 26 -- 7.5 -- 23 25 0.6 1.8 4.5 6 7 0.7 1.0 10.2 10.5 11.8 1.7 2.5 13.5 14.5 16 14 14 44 45 60 -- 12 -- 42 46 2 3.0 11.1 12.5 13.5 3.9 4.3 17 18 21 4.1 4.8 16.4 16.8 18.7 19 20 48 55 70 -- 22 -- 49 50 -- -- -- -- -- A A A A A A A A A A A A A A A A A A A A A A A A A 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 T1OSC Current (Note 1) T1OSC Current (Note 1) BOR Current (Note 1, Note 3, Note 5) BOR Current (Note 1, Note 3) FVR current (Note 1, Note 3, Note 5) FVR current (Note 1. Note 3) LPWDT Current (Note 1) LPWDT Current (Note 1) WDT, BOR, FVR, and T1OSC disabled, all Peripherals Inactive WDT, BOR, FVR, and T1OSC disabled, all Peripherals Inactive Typ Max. +85C Max. +125C Units Conditions VDD Note
PIC16LF722A/723A
PIC16F722A/723A Param No.
Device Characteristics Power-down Base Current
D020
2: 3: 4: 5:
Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is enabled. The peripheral current can be determined by subtracting the base IDD or IPD current from this limit. Max values should be used when calculating total current consumption. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD. Fixed Voltage Reference is automatically enabled whenever the BOR is enabled. A/D oscillator source is FRC. 0.1 F capacitor on VCAP (RA0).
DS41417A-page 204
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
23.3 DC Characteristics: PIC16F/LF722A/723A-I/E (Power-Down) (Continued)
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min.
(2)
PIC16LF722A/723A
PIC16F722A/723A Param No.
Device Characteristics
Typ
Max. +85C
Max. +125C
Units
Conditions VDD 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 1.8 3.0 1.8 3.0 5.0 Cap Sense High Power Oscillator mode Cap Sense High Power Oscillator mode Cap Sense Medium Power Oscillator mode Cap Sense Medium Power Oscillator mode Cap Sense Low Power Oscillator mode Cap Sense Low Power Oscillator mode A/D Current (Note 1, Note 4), conversion in progress A/D Current (Note 1, Note 4, Note 5), conversion in progress Note A/D Current (Note 1, Note 4), no conversion in progress A/D Current (Note 1, Note 4), no conversion in progress
Power-down Base Current (IPD) D027 D027
-- -- -- -- --
0.06 0.08 6 7 7.2 250 250 280 280 280 2.2 3.3 6.5 8 8 4.2 6 8.5 11 11 12 32 16 36 42
0.7 1.0 10.7 10.6 11.9 400 400 430 430 430 3.2 4.4 13 14 14 6 7 15.5 17 18 14 35 20 41 49
5.0 5.5 18 20 22 -- -- -- -- -- 14.4 15.6 21 23 25 17 18 23 24 27 25 44 31 50 58
A A A A A A A A A A A A A A A A A A A A A A A A A
D027A D027A
-- -- -- -- --
D028 D028
-- -- -- -- --
D028A D028A
-- -- -- -- --
D028B D028B
-- -- -- -- --
Note 1:
2: 3: 4: 5:
Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is enabled. The peripheral current can be determined by subtracting the base IDD or IPD current from this limit. Max values should be used when calculating total current consumption. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD. Fixed Voltage Reference is automatically enabled whenever the BOR is enabled. A/D oscillator source is FRC. 0.1 F capacitor on VCAP (RA0).
2010 Microchip Technology Inc.
DS41417A-page 205
PIC16F/LF722A/723A
23.4 DC Characteristics: PIC16F/LF722A/723A-I/E
DC CHARACTERISTICS Param No. Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min. Typ Max. Units Conditions
Sym. VIL
Characteristic Input Low Voltage I/O PORT: with TTL buffer with Schmitt Trigger buffer with I2CTM levels MCLR, OSC1 (RC mode)(1) OSC1 (HS mode)
D030 D030A D031 D032 D033A VIH D040 D040A D041 D042 D043A D043B IIL D060
-- -- -- -- -- --
-- -- -- -- -- -- --
0.8 0.15 VDD 0.2 VDD 0.3 VDD 0.2 VDD 0.3 VDD -- -- -- -- -- -- -- -- 125 1000 200 200 300
V V V V V V
4.5V VDD 5.5V 1.8V VDD 4.5V 2.0V VDD 5.5V
Input High Voltage I/O ports: with TTL buffer 2.0 0.25 VDD + 0.8 with Schmitt Trigger buffer with I2CTM levels MCLR OSC1 (HS mode) OSC1 (RC mode) Input Leakage Current(2) I/O ports -- 5 5 nA nA nA VSS VPIN VDD, Pin at highimpedance, 85C 125C VSS VPIN VDD, 85C VDD = 3.3V, VPIN = VSS VDD = 5.0V, VPIN = VSS IOL = 8mA, VDD = 5V IOL = 6mA, VDD = 3.3V IOL = 1.8mA, VDD = 1.8V IOH = 3.5mA, VDD = 5V IOH = 3mA, VDD = 3.3V IOH = 1mA, VDD = 1.8V In XT, HS and LP modes when external clock is used to drive OSC1 0.8 VDD 0.7 VDD 0.8 VDD 0.7 VDD 0.9 VDD -- -- -- -- -- -- -- V V V V V V V (Note 1) 4.5V VDD 5.5V 1.8V VDD 4.5V 2.0V VDD 5.5V
D061 IPUR D070* VOL D080
MCLR(3) PORTB Weak Pull-up Current
-- 25 25
50 100 140
A
Output Low Voltage(4) I/O ports -- -- 0.6 V
VOH D090
Output High Voltage(4) I/O ports VDD - 0.7 Capacitive Loading Specs on Output Pins -- -- V
D101*
COSC2 OSC2 pin
--
--
15
pF
D101A* CIO
All I/O pins
--
--
50
pF
Legend: TBD = To Be Determined * These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external clock in RC mode. 2: Negative current is defined as current sourced by the pin. 3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 4: Including OSC2 in CLKOUT mode.
DS41417A-page 206
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
23.4 DC Characteristics: PIC16F/LF722A/723A-I/E (Continued)
DC CHARACTERISTICS Param No. D130 D131 Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Min. Typ Max. Units Conditions
Sym.
Characteristic Program Flash Memory
EP
Cell Endurance VDD for Read Voltage on MCLR/VPP during Erase/Program VDD for Bulk Erase
100 VMIN 8.0 2.7 2.7
1k -- -- 3 --
-- -- 9.0 -- --
E/W V V V V
Temperature during programming: 10C TA 40C Temperature during programming: 10C TA 40C Temperature during programming: 10C TA 40C VMIN = Minimum operating voltage VMAX = Maximum operating voltage Temperature during programming: 10C TA 40C Temperature during programming: 10C TA 40C Temperature during programming: 10C TA 40C Provided no other specifications are violated
D132
VPEW
VDD for Write or Row Erase
IPPPGM
Current on MCLR/VPP during Erase/Write
-- -- -- 40
--
5.0 5.0 2.8
mA mA ms Year
IDDPGM Current on VDD during Erase/ Write D133 D134 TPEW TRETD Erase/Write cycle time Characteristic Retention VCAP Capacitor Charging D135 D135A Charging current Source/sink capability when charging complete
--
--
-- --
200 0.0
-- --
A
mA
Legend: TBD = To Be Determined * These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external clock in RC mode. 2: Negative current is defined as current sourced by the pin. 3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 4: Including OSC2 in CLKOUT mode.
2010 Microchip Technology Inc.
DS41417A-page 207
PIC16F/LF722A/723A
23.5 Thermal Considerations
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param No. TH01 Sym. JA Characteristic Thermal Resistance Junction to Ambient Typ. 60 80 90 27.5 27.5 TH02 JC Thermal Resistance Junction to Case 31.4 24 24 24 24 TH03 TH04 TH05 TH06 TH07 TJMAX PD PI/O PDER Maximum Junction Temperature Power Dissipation I/O Power Dissipation Derated Power 150 -- -- -- -- Units C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C W W W W PD = PINTERNAL + PI/O PINTERNAL = IDD x VDD(1) PI/O = (IOL * VOL) + (IOH * (VDD - VOH)) PDER = PDMAX (TJ - TA)/JA(2) Conditions 28-pin SPDIP package 28-pin SOIC package 28-pin SSOP package 28-pin UQFN 4x4mm package 28-pin QFN 6x6mm package 28-pin SPDIP package 28-pin SOIC package 28-pin SSOP package 28-pin UQFN 4x4mm package 28-pin QFN 6x6mm package
PINTERNAL Internal Power Dissipation
Note 1: IDD is current to run the chip alone without driving any load on the output pins. 2: TA = Ambient Temperature 3: TJ = Junction Temperature
DS41417A-page 208
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
23.6 Timing Parameter Symbology
The timing parameter symbols have been created with one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O PORT mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (High-impedance) L Low
T
Time
osc rd rw sc ss t0 t1 wr
OSC1 RD RD or WR SCK SS T0CKI T1CKI WR
P R V Z
Period Rise Valid High-impedance
FIGURE 23-2:
LOAD CONDITIONS
Load Condition
Pin
CL VSS
Legend: CL = 50 pF for all pins, 15 pF for OSC2 output
2010 Microchip Technology Inc.
DS41417A-page 209
PIC16F/LF722A/723A
23.7 AC Characteristics: PIC16F722A/723A-I/E
CLOCK TIMING
Q4 Q1 Q2 Q3 Q4 Q1
FIGURE 23-3:
OSC1/CLKIN OS02 OS03 OSC2/CLKOUT (LP,XT,HS Modes) OS04 OS04
OSC2/CLKOUT (CLKOUT Mode)
FIGURE 23-4:
5.5
PIC16F722A/723A VOLTAGE FREQUENCY GRAPH, -40C TA +125C
VDD (V)
3.6 2.5 2.3 2.0 1.8 0 4 10 Frequency (MHz) 16 20
Note 1: The shaded region indicates the permissible combinations of voltage and frequency. 2: Refer to Table 23-1 for each Oscillator mode's supported frequencies.
DS41417A-page 210
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 23-5: PIC16LF722A/723A VOLTAGE FREQUENCY GRAPH, -40C TA +125C
VDD (V)
3.6 2.5 2.3 2.0 1.8 0 4 10 Frequency (MHz) 16 20
Note 1: The shaded region indicates the permissible combinations of voltage and frequency. 2: Refer to Table 23-1 for each Oscillator mode's supported frequencies.
FIGURE 23-6:
125
HFINTOSC FREQUENCY ACCURACY OVER DEVICE VDD AND TEMPERATURE
+ 5% 85 3% Temperature (C) 60
25
2%
0 -20 -40 1.8 2.0 2.5 + 5% 3.0 3.3(2) 3.5 4.0 VDD (V)
Note 1: This chart covers both regulator enabled and regulator disabled states. 2: Regulator Nominal voltage.
4.5
5.0
5.5
2010 Microchip Technology Inc.
DS41417A-page 211
PIC16F/LF722A/723A
TABLE 23-1: CLOCK OSCILLATOR TIMING REQUIREMENTS
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param No. OS01 Sym. FOSC Characteristic External CLKIN Frequency(1) Min. DC DC DC DC Oscillator Frequency(1) -- 0.1 1 DC OS02 TOSC External CLKIN Period(1) 27 250 50 50 Oscillator Period(1) -- 250 50 250 OS03 OS04* TCY TosH, TosL TosR, TosF Instruction Cycle Time(1) External CLKIN High, External CLKIN Low External CLKIN Rise, External CLKIN Fall 200 2 100 20 OS05* 0 0 0 * Typ -- -- -- -- 32.768 -- -- -- -- -- -- -- 30.5 -- -- -- TCY -- -- -- -- -- -- Max. 37 4 20 20 -- 4 20 4 -- 10,000 1,000 -- DC -- -- -- Units kHz MHz MHz MHz kHz MHz MHz MHz s ns ns ns s ns ns ns ns s ns ns ns ns ns Conditions LP Oscillator mode XT Oscillator mode HS Oscillator mode EC Oscillator mode LP Oscillator mode XT Oscillator mode HS Oscillator mode, VDD 2.7V RC Oscillator mode LP Oscillator mode XT Oscillator mode HS Oscillator mode EC Oscillator mode LP Oscillator mode XT Oscillator mode HS Oscillator mode, VDD 2.7V RC Oscillator mode TCY = 4/FOSC LP oscillator XT oscillator HS oscillator LP oscillator XT oscillator HS oscillator
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min" values with an external clock applied to OSC1 pin. When an external clock input is used, the "max" cycle time limit is "DC" (no clock) for all devices.
DS41417A-page 212
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 23-2: OSCILLATOR PARAMETERS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param No. OS08 Sym. HFOSC Characteristic Internal Calibrated HFINTOSC Frequency(2) Internal Calibrated MFINTOSC Frequency(2) Freq. Tolerance 2% 5% OS08A MFOSC 2% 5% OS10* TIOSC ST HFINTOSC Wake-up from Sleep Start-up Time MFINTOSC Wake-up from Sleep Start-up Time * -- -- Min. -- -- -- -- -- -- Typ 16.0 16.0 500 500 5 20 Max. -- -- -- 10 8 30 Units MHz MHz kHz kHz s s Conditions 0C TA +85C, VDD V -40C TA +125C 0C TA +85C VDD V -40C TA +125C
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min" values with an external clock applied to the OSC1 pin. When an external clock input is used, the "max" cycle time limit is "DC" (no clock) for all devices. 2: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 F and 0.01 F values in parallel are recommended. 3: By design.
FIGURE 23-7:
Cycle
CLKOUT AND I/O TIMING
Write Q4 Fetch Q1 Read Q2 Execute Q3
FOSC OS11 CLKOUT OS19 OS13 I/O pin (Input) OS15 I/O pin (Output) Old Value OS18, OS19 OS14 New Value OS17 OS20 OS21 OS16 OS18 OS12
2010 Microchip Technology Inc.
DS41417A-page 213
PIC16F/LF722A/723A
TABLE 23-3: CLKOUT AND I/O TIMING PARAMETERS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param No. OS11 OS12 OS13 OS14 OS15 OS16 OS17 OS18 OS19 Sym. TosH2ckL TckL2ioV TioV2ckH TosH2ioV TosH2ioI TioV2osH TioR TioF Characteristic Fosc to CLKOUT (1)
(1) (1)
Min. -- -- -- TOSC + 200 ns -- 50 20 -- -- -- -- 25 TCY
Typ -- -- -- -- 50 -- -- 40 15 28 15 -- --
Max. 70 72 20 -- 70* -- -- 72 32 55 30 -- --
Units ns ns ns ns ns ns ns ns ns ns ns
Conditions VDD = 3.3-5.0V VDD = 3.3-5.0V
TosH2ckH Fosc to CLKOUT
CLKOUT to Port out valid
Port input valid before CLKOUT(1) Fosc (Q1 cycle) to Port out valid Fosc (Q2 cycle) to Port input invalid (I/O in hold time) Port input valid to Fosc(Q2 cycle) (I/O in setup time) Port output rise time(2) Port output fall time(2)
VDD = 3.3-5.0V VDD = 3.3-5.0V
VDD = 2.0V VDD = 3.3-5.0V VDD = 2.0V VDD = 3.3-5.0V
INT pin input high or low time PORTB interrupt-on-change new input level time * These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. Note 1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC. 2: Includes OSC2 in CLKOUT mode.
OS20* Tinp OS21* Trbp
FIGURE 23-8:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING
VDD MCLR Internal POR PWRT Time-out OSC Start-Up Time Internal Reset(1) Watchdog Timer Reset(1) 34 I/O pins Note 1: Asserted low. 31 34 33 32 30
DS41417A-page 214
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 23-9:
VDD VBOR VBOR and VHYST
BROWN-OUT RESET TIMING AND CHARACTERISTICS
(Device in Brown-out Reset)
(Device not in Brown-out Reset)
37
Reset (due to BOR)
33(1)
Note 1: 64 ms delay only if PWRTE bit in the Configuration Word register is programmed to `0'. 2 ms delay if PWRTE = 0 and VREGEN = 1.
2010 Microchip Technology Inc.
DS41417A-page 215
PIC16F/LF722A/723A
TABLE 23-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET PARAMETERS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param No. 30 31 32 33* 34* 35 36* 37* * Note 1: Sym. TMCL Characteristic MCLR Pulse Width (low) Min. 2 5 10 -- 40 -- 2.38 1.80 0 1 Typ -- -- 18 1024 65 -- 2.5 1.9 25 3 Max. -- -- 27 -- 140 2.0 2.73 2.11 50 5 10 Units s s ms Conditions VDD = 3.3-5V, -40C to +85C VDD = 3.3-5V VDD = 3.3V-5V
TWDTLP Low Power Watchdog Timer Timeout Period (No Prescaler) TOST TPWRT TIOZ VBOR VHYST Oscillator Start-up Timer Period(1), (2) Power-up Timer Period, PWRTE = 0 I/O high-impedance from MCLR Low or Watchdog Timer Reset Brown-out Reset Voltage Brown-out Reset Hysteresis
Tosc (Note 3) ms s V mV s BORV=2.5V BORV=1.9V -40C to +85C VDD VBOR, -40C to +85C VDD VBOR
TBORDC Brown-out Reset DC Response Time
2: 3: 4:
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min" values with an external clock applied to the OSC1 pin. When an external clock input is used, the "max" cycle time limit is "DC" (no clock) for all devices. By design. Period of the slower clock. To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 F and 0.01 F values in parallel are recommended.
FIGURE 23-10:
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
T0CKI 40 42 41
T1CKI 45 47 TMR0 or TMR1 46 49
DS41417A-page 216
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 23-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param No. 40* 41* 42* Sym. TT0H TT0L TT0P Characteristic T0CKI High Pulse Width T0CKI Low Pulse Width T0CKI Period No Prescaler With Prescaler No Prescaler With Prescaler Min. 0.5 TCY + 20 10 0.5 TCY + 20 10 Greater of: 20 or TCY + 40 N 0.5 TCY + 20 15 30 0.5 TCY + 20 15 30 Greater of: 30 or TCY + 40 N 60 32.4 2 TOSC Typ -- -- -- -- -- Max. -- -- -- -- -- Units ns ns ns ns ns N = prescale value (2, 4, ..., 256) Conditions
45*
TT1H
T1CKI High Synchronous, No Prescaler Time Synchronous, with Prescaler Asynchronous T1CKI Low Time Synchronous, No Prescaler Synchronous, with Prescaler Asynchronous
-- -- -- -- -- -- --
-- -- -- -- -- -- --
ns ns ns ns ns ns ns N = prescale value (1, 2, 4, 8)
46*
TT1L
47*
TT1P
T1CKI Input Synchronous Period Asynchronous
-- 32.768 --
-- 33.1 7 TOSC
ns kHz -- Timers in Sync mode
48 49* *
FT1
Timer1 Oscillator Input Frequency Range (oscillator enabled by setting bit T1OSCEN)
TCKEZTMR1 Delay from External Clock Edge to Timer Increment
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
FIGURE 23-11:
CAPTURE/COMPARE/PWM TIMINGS (CCP)
CCPx (Capture mode)
CC01 CC03 Note: Refer to Figure 23-2 for load conditions.
CC02
TABLE 23-6:
CAPTURE/COMPARE/PWM REQUIREMENTS (CCP)
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param Sym. No. CC01* TccL CC02* TccH CC03* TccP * Characteristic CCPx Input Low Time CCPx Input High Time CCPx Input Period No Prescaler With Prescaler No Prescaler With Prescaler Min. 0.5TCY + 20 20 0.5TCY + 20 20 3TCY + 40 N Typ -- -- -- -- -- Max. -- -- -- -- -- Units ns ns ns ns ns N = prescale value (1, 4 or 16) Conditions
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
2010 Microchip Technology Inc.
DS41417A-page 217
PIC16F/LF722A/723A
TABLE 23-7: PIC16F722A/723A A/D CONVERTER (ADC) CHARACTERISTICS:
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param Sym. No. AD01 AD02 AD03 AD04 AD05 AD06 AD07 AD08 NR EIL EDL Characteristic Resolution Integral Error Differential Error Min. -- -- -- -- -- 1.8 VSS -- Typ -- -- -- -- -- -- -- -- Max. 8 1.7 1 2.2 1.5 VDD VREF 50 Units bit LSb VREF = 3.0V LSb No missing codes VREF = 3.0V LSb VREF = 3.0V LSb VREF = 3.0V V V Conditions
EOFF Offset Error EGN VAIN ZAIN Gain Error Full-Scale Range Recommended Impedance of Analog Voltage Source VREF Reference Voltage(3)
k Can go higher if external 0.01F capacitor is
present on input pin.
Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Total Absolute Error includes integral, differential, offset and gain errors. 2: The A/D conversion result never decreases with an increase in the input voltage and has no missing codes. 3: When ADC is off, it will not consume any current other than leakage current. The power-down current specification includes any such leakage from the ADC module.
TABLE 23-8:
PIC16F722A/723A A/D CONVERSION REQUIREMENTS
Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param No. Sym. Characteristic A/D Clock Period A/D Internal RC Oscillator Period AD131 TCNV Conversion Time (not including Acquisition Time)(1) Acquisition Time Min. 1.0 1.0 -- -- Typ -- 2.0 10.5 1.0 Max. 9.0 6.0 -- -- Units s s TAD s TOSC-based ADCS<1:0> = 11 (ADRC mode) Set GO/DONE bit to conversion complete Conditions
AD130* TAD
AD132* TACQ *
These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The ADRES register may be read on the following TCY cycle.
DS41417A-page 218
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 23-12: PIC16F722A/723A A/D CONVERSION TIMING (NORMAL MODE)
1 TCY AD131 AD130 A/D CLK A/D Data ADRES ADIF GO Sample AD132 Sampling Stopped 7 6 OLD_DATA 5 4 3 2 1 0 NEW_DATA 1 TCY DONE BSF ADCON0, GO AD134 Q4
(TOSC/2(1))
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed.
FIGURE 23-13:
PIC16F722A/723A A/D CONVERSION TIMING (SLEEP MODE)
BSF ADCON0, GO AD134 Q4 A/D CLK A/D Data ADRES ADIF GO Sample AD132 Sampling Stopped 7 6 5 4 3 2 1 0 NEW_DATA 1 TCY DONE (TOSC/2 + TCY(1)) AD131 AD130 1 TCY
OLD_DATA
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed.
2010 Microchip Technology Inc.
DS41417A-page 219
PIC16F/LF722A/723A
FIGURE 23-14: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
CK US121 DT US120 Note: Refer to Figure 23-2 for load conditions. US122 US121
TABLE 23-9:
USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param. No. Symbol Characteristic 3.0-5.5V 1.8-5.5V 3.0-5.5V 1.8-5.5V 3.0-5.5V 1.8-5.5V Min. -- -- -- -- -- -- Max. 80 100 45 50 45 50 Units ns ns ns ns ns ns Conditions
US120 TCKH2DTV SYNC XMIT (Master and Slave) Clock high to data-out valid US121 TCKRF US122 TDTRF Clock out rise time and fall time (Master mode) Data-out rise time and fall time
FIGURE 23-15:
CK DT
USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
US125
US126 Note: Refer to Figure 23-2 for load conditions.
TABLE 23-10: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +125C Param. No. Symbol Characteristic Min. 10 15 Max. -- -- Units ns ns Conditions
US125 TDTV2CKL SYNC RCV (Master and Slave) Data-hold before CK (DT hold time) US126 TCKL2DTL Data-hold after CK (DT hold time)
DS41417A-page 220
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 23-16:
SS SP70 SCK (CKP = 0) SP71 SP72 SP78 SCK (CKP = 1) SP79 SP80 SDO MSb bit 6 - - - - - -1 SP75, SP76 SDI MSb In SP74 SP73 bit 6 - - - -1 LSb In LSb SP78 SP79
SPI MASTER MODE TIMING (CKE = 0, SMP = 0)
Note:
Refer to Figure 23-2 for load conditions.
FIGURE 23-17:
SS
SPI MASTER MODE TIMING (CKE = 1, SMP = 1)
SP81 SCK (CKP = 0) SP71 SP73 SCK (CKP = 1) SP80 SP78 LSb SP72 SP79
SDO
MSb
bit 6 - - - - - -1 SP75, SP76
SDI
MSb In SP74
bit 6 - - - -1
LSb In
Note:
Refer to Figure 23-2 for load conditions.
2010 Microchip Technology Inc.
DS41417A-page 221
PIC16F/LF722A/723A
FIGURE 23-18:
SS SP70 SCK (CKP = 0) SP71 SP72 SP78 SCK (CKP = 1) SP79 SP80 SDO MSb bit 6 - - - - - -1 SP75, SP76 SDI MSb In SP74 SP73 bit 6 - - - -1 LSb In LSb SP77 SP78 SP79 SP83
SPI SLAVE MODE TIMING (CKE = 0)
Note:
Refer to Figure 23-2 for load conditions.
FIGURE 23-19:
SS
SPI SLAVE MODE TIMING (CKE = 1)
SP82 SP70
SCK (CKP = 0) SP71 SCK (CKP = 1) SP80 SP72
SP83
SDO
MSb
bit 6 - - - - - -1 SP75, SP76
LSb SP77
SDI
MSb In SP74
bit 6 - - - -1
LSb In
Note:
Refer to Figure 23-2 for load conditions.
DS41417A-page 222
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 23-11: SPI MODE REQUIREMENTS
Param No. Symbol Characteristic Min. TCY TCY + 20 TCY + 20 100 100 -- -- -- 10 -- -- -- 3.0-5.5V 1.8-5.5V -- -- Tcy -- 1.5TCY + 40 3.0-5.5V 1.8-5.5V Typ -- -- -- -- -- 10 25 10 -- 10 25 10 -- -- -- -- -- Max. Units Conditions -- -- -- -- -- 25 50 25 50 25 50 25 50 145 -- 50 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
SP70* TSSL2SCH, SS to SCK or SCK input TSSL2SCL SP71* TSCH SP72* TSCL SCK input high time (Slave mode) SCK input low time (Slave mode)
SP73* TDIV2SCH, Setup time of SDI data input to SCK edge TDIV2SCL SP74* TSCH2DIL, TSCL2DIL SP75* TDOR SP76* TDOF SP77* TSSH2DOZ SP78* TSCR SP79* TSCF Hold time of SDI data input to SCK edge SDO data output rise time SDO data output fall time SS to SDO output high-impedance SCK output rise time (Master mode) SCK output fall time (Master mode) 3.0-5.5V 1.8-5.5V
SP80* TSCH2DOV, SDO data output valid after TSCL2DOV SCK edge
SP81* TDOV2SCH, SDO data output setup to SCK edge TDOV2SCL SP82* TSSL2DOV SDO data output valid after SS edge SP83* TSCH2SSH, SS after SCK edge TSCL2SSH
* These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
FIGURE 23-20:
I2CTM BUS START/STOP BITS TIMING
SCL SP91 SP90 SDA SP92 SP93
Start Condition
Stop Condition
Note:
Refer to Figure 23-2 for load conditions.
2010 Microchip Technology Inc.
DS41417A-page 223
PIC16F/LF722A/723A
TABLE 23-12: I2CTM BUS START/STOP BITS REQUIREMENTS
Param No. SP90* SP91* SP92* SP93 * Symbol TSU:STA THD:STA TSU:STO Characteristic Start condition Setup time Start condition Hold time Stop condition Setup time THD:STO Stop condition Hold time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Min. 4700 600 4000 600 4700 600 4000 600 Typ -- -- -- -- -- -- -- -- Max. Units -- -- -- -- -- -- -- -- ns ns ns ns Conditions Only relevant for Repeated Start condition After this period, the first clock pulse is generated
These parameters are characterized but not tested.
FIGURE 23-21:
I2CTM BUS DATA TIMING
SP103 SP100 SP101 SP102
SCL
SP90 SP91
SP106
SP107
SP92 SP110
SDA In SP109 SDA Out SP109
Note:
Refer to Figure 23-2 for load conditions.
DS41417A-page 224
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
TABLE 23-13: I2CTM BUS DATA REQUIREMENTS
Param. No. Symbol Characteristic Clock high time 100 kHz mode 400 kHz mode SSP Module SP101* TLOW Clock low time 100 kHz mode 400 kHz mode SSP Module SP102* TR SDA and SCL rise time SDA and SCL fall time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Min. 4.0 0.6 1.5TCY 4.7 1.3 1.5TCY -- 20 + 0.1CB -- 20 + 0.1CB 0 0 250 100 -- -- 4.7 1.3 -- Max. -- -- -- -- -- -- 1000 300 250 250 -- 0.9 -- -- 3500 -- -- -- 400 ns ns ns ns ns s ns ns ns ns s s pF Time the bus must be free before a new transmission can start (Note 1) (Note 2) CB is specified to be from 10-400 pF CB is specified to be from 10-400 pF s s Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz Units s s Conditions Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz
SP100* THIGH
SP103* TF
SP106* THD:DAT SP107* TSU:DAT SP109* TAA SP110* TBUF
Data input hold time 100 kHz mode 400 kHz mode Data input setup time Output valid from clock Bus free time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode
SP111 * Note 1: 2:
CB
Bus capacitive loading
These parameters are characterized but not tested. As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. A Fast mode (400 kHz) I2CTM bus device can be used in a Standard mode (100 kHz) I2C bus system, but the requirement TSU:DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the low period of the SCL signal. If such a device does stretch the low period of the SCL signal, it must output the next data bit to the SDA line TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCL line is released.
2010 Microchip Technology Inc.
DS41417A-page 225
PIC16F/LF722A/723A
TABLE 23-14: CAP SENSE OSCILLATOR SPECIFICATIONS
Param. No. CS01 Symbol ISRC Characteristic Current Source High Medium Low CS02 ISNK Current Sink High Medium Low CS03 VCHYST Cap Hysteresis High Medium Low Min. -- -- -- -- -- -- -- -- -- Typ -5.8 -1.1 -0.2 6.6 1.3 0.24 525 375 280 Max. -6 -3.2 -0.9 6 3.2 0.9 -- -- -- Units A A A A A A mV mV mV VCTH-VCTL -40, -85C -40, -85C Conditions
* These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
FIGURE 23-22:
CAP SENSE OSCILLATOR
VCTH
VCTL
ISRC Enabled
ISNK Enabled
DS41417A-page 226
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
24.0
Note:
DC AND AC CHARACTERISTICS GRAPHS AND CHARTS
The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore, outside the warranted range.
"Typical" represents the mean of the distribution at 25C. "Maximum" or "minimum" represents (mean + 3) or (mean - 3) respectively, where is a standard deviation, over the whole temperature range.
FIGURE 24-1:
2,200.00 2,000.00 1,800.00 1,600.00 1,400.00 IDD (A) 1,200.00 1,000.00
PIC16F722A/723A MAXIMUM IDD vs. FOSC OVER VDD, EC MODE, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V 3.6V 3V
2.5V
1.8V 800.00 600.00 400.00 200.00 0.00 1 MHz 4 MHz 8 MHz VDD (V) 12 MHz 16 MHz 20 MHz
2010 Microchip Technology Inc.
DS41417A-page 227
PIC16F/LF722A/723A
FIGURE 24-2:
2,400 2,200 2,000 1,800 3V 1,600 1,400 1,200 2V 1,000 1.8V 800 600 400 200 0 1 MHz 4 MHz 8 MHz FOSC 12 MHz 16 MHz 20 MHz 2.5V Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
PIC16LF722A/723A MAXIMUM IDD vs. FOSC OVER VDD, EC MODE
3.6V 3.3V
FIGURE 24-3:
2,000 1,800 1,600 1,400
IDD (A)
PIC16F722A/723A TYPICAL IDD vs. FOSC OVER VDD, EC MODE, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V 3.6V 3V
2.5V 1,200 IDD (A) 1,000 800 600 400 200 0 1 MHz 4 MHz 8 MHz FOSC 12 MHz 16 MHz 20 MHz 1.8V
DS41417A-page 228
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-4:
2,200 2,000 1,800 1,600 1,400 IDD (A) 1,200 1,000 800 600 400 200 0 1 MHz 4 MHz 8 MHz FOSC 12 MHz 16 MHz 20 MHz 2V 1.8V Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 3.6V 3.3V 3V
PIC16LF722A/723A TYPICAL IDD vs. FOSC OVER VDD, EC MODE
2.5V
FIGURE 24-5:
600
PIC16F722A/723A MAXIMUM IDD vs. VDD OVER FOSC, EXTRC MODE, VCAP = 0.1F
500
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
4 MHz
400
IDD (A)
300 1 MHz
200
100
0 1.8 2 2.5 3 3.3 VDD (V) 3.6 4.2 4.5 5
2010 Microchip Technology Inc.
DS41417A-page 229
PIC16F/LF722A/723A
FIGURE 24-6:
500 450 400 350 300 IDD (A) 250 200 150 100 50 0 1.8 2 2.5 VDD (V) 3 3.3 3.6 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 4 MHz
PIC16LF722A/723A MAXIMUM IDD vs. VDD OVER FOSC, EXTRC MODE
1 MHz
FIGURE 24-7:
450 400 350 300 250 200 150
PIC16F722A/723A TYPICAL IDD vs. VDD OVER FOSC, EXTRC MODE, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
4 MHz
IDD (A)
1 MHz 100 50 0 1.8 2 2.5 3 3.3 VDD (V) 3.6 4.2 4.5 5
DS41417A-page 230
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-8:
450 400 350 300 250 200 150 1 MHz 100 50 0 1.8 2 2.5 VDD (V) 3 3.3 3.6 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 4 MHz
PIC16LF722A/723A TYPICAL IDD vs. VDD OVER FOSC, EXTRC MODE
IDD (A)
FIGURE 24-9:
2.4 2.2 2 1.8 1.6 1.4 IDD (mA) 1.2 1 0.8 0.6 0.4 0.2 0 4 MHz
PIC16F722A/723A MAXIMUM IDD vs. FOSC OVER VDD, HS MODE, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V 4.5V 3.6V 3V
6 MHz
8 MHz
10 MHz Fosc
13 MHz
16 MHz
20 MHz
2010 Microchip Technology Inc.
DS41417A-page 231
PIC16F/LF722A/723A
FIGURE 24-10:
2.50 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 2.00
PIC16LF722A/723A MAXIMUM IDD vs. FOSC OVER VDD, HS MODE
3.6V 3.3V 3V
1.50 IDD (mA) 2.5V
1.00
0.50
0.00 4 MHz 6 MHz 8 MHz 10 MHz Fosc 13 MHz 16 MHz 20 MHz
FIGURE 24-11:
PIC16F722A/723A TYPICAL IDD vs. FOSC OVER VDD, HS MODE, VCAP = 0.1F
2.00
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V 4.5V 3.6V 3V
1.50
IDD (mA)
1.00
0.50
0.00 4 MHz 6 MHz 8 MHz 10 MHz Fosc 13 MHz 16 MHz 20 MHz
DS41417A-page 232
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-12:
2.50 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 2.00 3.6V 3.3V 3V 1.50 IDD (mA) 2.5V
PIC16LF722A/723A TYPICAL IDD vs. FOSC OVER VDD, HS MODE
1.00
0.50
0.00 4 MHz 6 MHz 8 MHz 10 MHz Fosc 13 MHz 16 MHz 20 MHz
FIGURE 24-13:
600
PIC16F722A/723A MAXIMUM IDD vs. VDD OVER FOSC, XT MODE, VCAP = 0.1F
500
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
4 MHz
400
IDD (A)
300
1 MHz
200
100
0 1.8 2 2.5 3 3.3 VDD (V) 3.6 4.2 4.5 5
2010 Microchip Technology Inc.
DS41417A-page 233
PIC16F/LF722A/723A
FIGURE 24-14:
600 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 4 MHz
PIC16LF722A/723A MAXIMUM IDD vs. VDD OVER FOSC, XT MODE
500
400
IDD (A)
300 1 MHz 200
100
0 1.8 2 2.5 VDD (V) 3 3.3 3.6
FIGURE 24-15:
600
PIC16F722A/723A TYPICAL IDD vs. VDD OVER FOSC, XT MODE, VCAP = 0.1F
500
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
4 MHz
400 IDD (A)
300 1 MHz 200
100
0 1.8 2 2.5 3 3.3 VDD (V) 3.6 4.2 4.5 5
DS41417A-page 234
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-16:
600 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 4 MHz
PIC16LF722A/723A TYPICAL IDD vs. VDD OVER FOSC, XT MODE
500
400
IDD (A)
300
200
1 MHz
100
0 1.8 2 2.5 VDD (V) 3 3.3 3.6
FIGURE 24-17:
20.0
PIC16F722A/723A IDD vs. VDD, LP MODE, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 17.5 32 kHz Maximum
IDD (A)
15.0 VDD (V)
32 kHz Typical 12.5
10.0 1.8 3 VDD (V) 5
2010 Microchip Technology Inc.
DS41417A-page 235
PIC16F/LF722A/723A
FIGURE 24-18:
30 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 25
PIC16LF722A/723A IDD vs. VDD, LP MODE
32 kHz Maximum 20 IDD (A)
15
10
32 kHz Typical
5 1.8 3 VDD (V) 3.3 3.6
FIGURE 24-19:
PIC16F722A/723A MAXIMUM IDD vs. FOSC OVER VDD, INTOSC MODE, VCAP = 0.1F
210 200 190 180 170 IDD (A) 160 150 140 130 120 110 62.5 kHz 125 kHz FOSC 250 kHz 500 kHz 3.6V 2.5V Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V
1.8V
DS41417A-page 236
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-20:
170 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 3.6V
PIC16LF722A/723A MAXIMUM IDD vs. FOSC OVER VDD, INTOSC MODE
160
150
3V 2.5V
IDD (A)
140
130 1.8V 120
110
100 62.5 KHz 125 KHz FOSC 250 KHz 500 KHz
FIGURE 24-21:
PIC16F722A/723A MAXIMUM IDD vs. FOSC OVER VDD, INTOSC MODE, VCAP = 0.1F
5V 3.6V
2,000 1,800 1,600 1,400 1,200 IDD (A) 1,000 800 600 400 200 0 2 MHz 4 MHz FOSC 8 MHz 16 MHz 1.8V 2.5V Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
2010 Microchip Technology Inc.
DS41417A-page 237
PIC16F/LF722A/723A
FIGURE 24-22:
2,250 s Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 3.6V
PIC16LF722A/723A MAXIMUM IDD vs. FOSC OVER VDD, INTOSC MODE
2,000
1,750
3V
1,500 2.5V IDD (A) 1,250 1.8V
1,000
750
500
250
0 2 MHz 4 MHz FOSC 8 MHz 16 MHz
FIGURE 24-23:
PIC16F722A/723A TYPICAL IDD vs. FOSC OVER VDD, INTOSC MODE, VCAP = 0.1F
160 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
150
5V 3.6V
140
IDD (A)
130 2.5V 120 1.8V 110
100
90
80 62.5 kHz 125 kHz FOSC 250 kHz 500 kHz
DS41417A-page 238
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-24:
140 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 3.6V
PIC16LF722A/723A TYPICAL IDD vs. FOSC OVER VDD, INTOSC MODE
130
120
3V
2.5V 110 IDD (A)
100
1.8V
90
80
70 62.5 kHz 125 kHz FOSC 250 kHz 500 kHz
FIGURE 24-25:
PIC16F722A/723A TYPICAL IDD vs. FOSC OVER VDD, INTOSC MODE, VCAP = 0.1F
2,000 1,800 1,600 1,400 2.5V 1,200 IDD (A) 1,000 1.8V 800 600 400 200 0 2 MHz 4 MHz FOSC 8 MHz 16 MHz Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
5V 3.6V
2010 Microchip Technology Inc.
DS41417A-page 239
PIC16F/LF722A/723A
FIGURE 24-26:
2,000 1,800 1,600 1,400 2.5V IDD (A) 1,200 1,000 800 600 400 200 0 2 MHz 4 MHz VDD (V) 8 MHz 16 MHz Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 3.6V
PIC16LF722A/723A TYPICAL IDD vs. FOSC OVER VDD, INTOSC MODE
3V
1.8V
FIGURE 24-27:
25
PIC16F722A/723A MAXIMUM BASE IPD vs. VDD, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 20 125C
15 IPD (A)
85C 10
5
0 1.8V 2V 3V 3.6V VDD (V) 4V 5V 5.5V
DS41417A-page 240
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-28:
7 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
PIC16LF722A/723A MAXIMUM BASE IPD vs. VDD
6
125C
5
IPD (A)
4
3
2 85C 1
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-29:
8
PIC16F722A/723A TYPICAL BASE IPD vs. VDD, VCAP = 0.1F
7
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
6 25C IPD (A) 5
4
3
2 1.8V 2V 3V 3.6V VDD (V) 4V 5V 5.5V
2010 Microchip Technology Inc.
DS41417A-page 241
PIC16F/LF722A/723A
FIGURE 24-30:
250 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 200 25C
PIC16LF722A/723A TYPICAL BASE IPD vs. VDD
150 IPD (nA) 100 50
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-31:
70
PIC16F722A/723A FIXED VOLTAGE REFERENCE IPD vs. VDD, VCAP = 0.1F
60
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
Max. 125C
50 Max. 85C 40 IPD (A)
30 Typ. 25C 20
10
0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
DS41417A-page 242
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-32:
25 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 20
PIC16LF722A/723A FIXED VOLTAGE REFERENCE IPD vs. VDD
Max. 125C
15 Max. 85C IPD (A) 10 Typ. 25C 5 0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-33:
70
PIC16F722A/723A BOR IPD vs. VDD, VCAP = 0.1F
60
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 125C
50
40 IPD (A)
Max. 85C
30 Typ. 25C 20
10
0 2V 3V 3.6V VDD (V) 5V 5.5V
2010 Microchip Technology Inc.
DS41417A-page 243
PIC16F/LF722A/723A
FIGURE 24-34:
30 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 125C 20
PIC16LF722A/723A BOR IPD vs. VDD
25
IPD (A)
15 Max. 85C 10 Typ. 25C 5
0 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-35:
70
PIC16F722A/723A CAP SENSE HIGH POWER IPD vs. VDD, VCAP = 0.1F
60
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
Max. 125C
50
Max. 85C
Typ. 25C 40 IPD (A)
30
20
10
0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
DS41417A-page 244
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-36:
60 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 125C
PIC16LF722A/723A CAP SENSE HIGH POWER IPD vs. VDD
50
Max. 85C 40 Typ. 25C IPD (A) 30
20
10
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-37:
30
PIC16F722A/723A CAP SENSE MEDIUM POWER IPD vs. VDD, VCAP = 0.1F
Max. 125C
25
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
20 Max. 85C
IPD (A)
15 Typ. 25C 10
5
0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
2010 Microchip Technology Inc.
DS41417A-page 245
PIC16F/LF722A/723A
FIGURE 24-38:
20 18 16 14 12 IPD (A) 10 8 6 4 2 0 1.8V 2V 2.5V VDD (V) 3V 3.6V Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 125C
PIC16LF722A/723A CAP SENSE MEDIUM POWER IPD vs. VDD
Max. 85C Typ. 25C
FIGURE 24-39:
30
PIC16F722A/723A CAP SENSE LOW POWER IPD vs. VDD, VCAP = 0.1F
25
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
Max. 125C
20
IPD (A)
15
Max. 85C
10 Typ. 25C 5
0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
DS41417A-page 246
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-40:
18 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 125C
PIC16LF722A/723A CAP SENSE LOW POWER IPD vs. VDD
16
14
12
10 IPD (A)
8
6 Max. 85C 4 Typ. 25C 2
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-41:
16
PIC16F722A/723A T1OSC 32 kHz IPD vs. VDD, VCAP = 0.1F
14
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
Max. 85C
12
10 IPD (A) Typ. 25 C 8
6
4
2
0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
2010 Microchip Technology Inc.
DS41417A-page 247
PIC16F/LF722A/723A
FIGURE 24-42:
4.0 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 85C
PIC16LF722A/723A T1OSC 32 kHz IPD vs. VDD
3.5
3.0
2.5 Typ. IPD (A) 2.0
1.5
1.0
0.5
0.0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-43:
7.5
PIC16F722A/723A TYPICAL ADC IPD vs. VDD, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 7.0
Typ. 25C
6.5 IPD (A)
6.0
5.5
5.0 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
DS41417A-page 248
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-44:
250 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 200 Typ. 25C
PIC16LF722A/723A TYPICAL ADC IPD vs. VDD
150 IPD (nA)
100
50
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-45:
25
PIC16F722A/723A ADC IPD vs. VDD, VCAP = 0.1F
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) 20
Max. 125C
IPD (A)
15
Max. 85C 10
5 1.8V 2V 3V VDD (V) 3.6V 5V 5.5V
2010 Microchip Technology Inc.
DS41417A-page 249
PIC16F/LF722A/723A
FIGURE 24-46:
8 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
PIC16LF722A/723A ADC IPD vs. VDD
7
Max. 125C
6
5 IPD (A)
4
3
2 Max. 85C 1
0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-47:
18 16 14 12 10 IPD (A) 8 6 4 2 0 1.8V
PIC16F722A/723A WDT IPD vs. VDD, VCAP = 0.1F
Max. 85C
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
Typ. 25C
2V
3V VDD (V)
3.6V
5V
5.5V
DS41417A-page 250
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-48:
3.5 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. 85C
PIC16LF722A/723A WDT IPD vs. VDD
3.0
2.5
2.0 IPD (A)
1.5 Typ. 25C 1.0
0.5
0.0 1.8V 2V 2.5V VDD (V) 3V 3.6V
FIGURE 24-49:
1.8
TTL INPUT THRESHOLD VIN vs. VDD OVER TEMPERATURE
1.6
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
1.4
Max. -40
1.2 VIN (V) Typ. 25 1
0.8
Min. 125
0.6
0.4 1.8 3.6 VDD (V) 5.5
2010 Microchip Technology Inc.
DS41417A-page 251
PIC16F/LF722A/723A
FIGURE 24-50:
3.5 Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
SCHMITT TRIGGER INPUT THRESHOLD VIN vs. VDD OVER TEMPERATURE
3.0
2.5
VIHMax. -40C
2.0 VIN (V)
1.5 VIHMin. 125C 1.0
0.5
0.0 1.8 3.6 VDD (V) 5.5
FIGURE 24-51:
3.0
SCHMITT TRIGGER INPUT THRESHOLD VIN vs. VDD OVER TEMPERATURE
2.5
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C) VIL Max. -40C
2.0
VIN (V)
1.5
1.0
VIL Min. 125C
0.5
0.0 1.8 3.6 VDD (V) 5.5
DS41417A-page 252
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-52:
5.6
VOH vs. IOH OVER TEMPERATURE, VDD = 5.5V
5.5
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
5.4
VOH (V)
5.3
Max. -40
5.2
Typ. 25
5.1
Min. 125
5 -0.2 -1.0 -1.8 -2.6 IOH (mA) -3.4 -4.2 -5.0
FIGURE 24-53:
3.8
VOH vs. IOH OVER TEMPERATURE, VDD = 3.6V
3.6
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
3.4 Max. -40 VOH (V)
3.2 Typ. 25
3 Min. 125 2.8
2.6 -0.2 -1.0 -1.8 -2.6 IOH (mA) -3.4 -4.2 -5.0
2010 Microchip Technology Inc.
DS41417A-page 253
PIC16F/LF722A/723A
FIGURE 24-54:
2 1.8 1.6 Max. -40 1.4 1.2 VOH (V) 1 0.8 0.6 Min. 125 0.4 0.2 0 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 -1.4 -1.6 -1.8 -2.0 IOH (mA) Typ. 25 Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
VOH vs. IOH OVER TEMPERATURE, VDD = 1.8V
FIGURE 24-55:
0.5 0.45 0.4 0.35
VOL vs. IOL OVER TEMPERATURE, VDD = 5.5V
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
Max. 125 0.3 0.25 0.2 Typ. 25 0.15 0.1 Min. -40 0.05 0 5.0 6.0 7.0 IOL (mA) 8.0 9.0 10.0
VOL (V)
DS41417A-page 254
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-56:
0.9 Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
VOL vs. IOL OVER TEMPERATURE, VDD = 3.6
0.8
0.7
0.6 Max. 125 0.5 VOL (V)
0.4 Typ. 25
0.3
0.2 Min. -40 0.1
0 4.0 5.0 6.0 7.0 IOL (mA) 8.0 9.0 10.0
FIGURE 24-57:
1.2
VOL vs. IOL OVER TEMPERATURE, VDD = 1.8V
1
Maximum: Mean + 3 (-40C to 125C) Typical: Mean @25C Minimum: Mean - 3 (-40C to 125C)
0.8 Max. 125 VOL (V) 0.6
0.4
0.2 Min. -40
0 0.0 0.4 0.8 1.2 1.6 IOL (mA) 2.0 2.4 2.8
2010 Microchip Technology Inc.
DS41417A-page 255
PIC16F/LF722A/723A
FIGURE 24-58:
105 Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. -40C 85 TIME (ms)
PIC16F722A/723A PWRT PERIOD
95
75
Typ. 25C
65 Min. 125C 55
45 1.8V 2V 2.2V 2.4V 3V VDD 3.6V 4V 4.5V 5V 5.5V
FIGURE 24-59:
24.00
PIC16F722A/723A WDT TIME-OUT PERIOD
22.00
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C) Max. -40C
20.00
18.00 TIME (ms) Typ. 25C 16.00
14.00 Min. 125C 12.00
10.00 1.8V 2V 2.2V 2.4V 3V VDD 3.6V 4V 4.5V 5V
DS41417A-page 256
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-60:
6.0 5.5 5.0 4.5 4.0 TIME (us) 3.5 3.0 Typ. 2.5 2.0 1.5 1.0 1.8V 2V 3V 3.6V VDD 4V 4.5V 5V 5.5V Max. Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
PIC16F722A/723A HFINTOSC WAKE-UP FROM SLEEP START-UP TIME
FIGURE 24-61:
6.0
PIC16F722A/723A A/D INTERNAL RC OSCILLATOR PERIOD
5.0
Typical: Statistical Mean @25C Maximum: Mean (Worst-Case Temp) + 3 (-40C to 125C)
4.0 Period (s)
3.0
Max.
2.0
Min.
1.0
0.0 1.8V 3.6V VDD(V) 5.5V
2010 Microchip Technology Inc.
DS41417A-page 257
PIC16F/LF722A/723A
FIGURE 24-62:
20000
PIC16F722A/723A CAP SENSE OUTPUT CURRENT, POWER MODE = HIGH
15000
Min. Sink -40C
10000 Current (nA)
Typ. Sink 25C
5000
Max. Sink 85C
0 Min. Source 85C -5000 Typ. Source 25C -10000 Max. Source -40C -15000 1.8 2 2.5 3 3.2 VDD(V) 3.6 4 4.5 5 5.5
FIGURE 24-63:
3000
PIC16F722A/723A CAP SENSE OUTPUT CURRENT, POWER MODE = MEDIUM
Max. Sink -40C
2000
Typ. Sink 25C
1000 Min. Sink 85C Current (nA)
0 Min. Source 85C
-1000
Typ. Source 25C
-2000 Max. Source -40C
-3000 1.8 2 2.5 3 3.2 VDD(V) 3.6 4 4.5 5 5.5
DS41417A-page 258
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-64:
600
PIC16F722A/723A CAP SENSE OUTPUT CURRENT, POWER MODE = LOW
400
Max. Sink 85C Typ. Sink 25C
200 Min. Sink -40C 0 Current (nA) Min. Source 85C
-200
Typ. Source 25C -400
-600 Max. Source -40C -800 1.8 2 2.5 3 3.2 VDD(V) 3.6 4 4.5 5 5.5
FIGURE 24-65:
PIC16F722A/723A CAP SENSOR HYSTERESIS, POWER MODE = HIGH
700 Max. 125C
600
Max. 85C
Typ. 25C mV 500 Min. 0C
Min. -40C 400
300 1.8 2.0 2.5 3.0 3.2 VDD(V) 3.6 4.0 4.5 5.0 5.5
2010 Microchip Technology Inc.
DS41417A-page 259
PIC16F/LF722A/723A
FIGURE 24-66:
550
PIC16F722A/723A CAP SENSOR HYSTERESIS, POWER MODE = MEDIUM
500 Max. 125C
450
Max. 85C
mV
400 Typ. 25C
350 Min. 0C 300 Min. -40C
250 1.8 2.0 2.5 3.0 3.2 VDD(V) 3.6 4.0 4.5 5.0 5.5
FIGURE 24-67:
450
PIC16F722A/723A CAP SENSOR HYSTERESIS, POWER MODE = LOW
400
Max. 125C
Max. 85C 350
mV
300
Typ. 25C
250
Min. 0C
200
Min -40C
150 1.8 2.0 2.5 3.0 3.2 VDD(V) 3.6 4.0 4.5 5.0 5.5
DS41417A-page 260
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
FIGURE 24-68: TYPICAL FVR (X1 AND X2) VS. SUPPLY VOLTAGE (V) NORMALIZED AT 3.0V
1.5
1
Percent Change (%)
0.5
0
-0.5
-1
-1.5 1.8 2.5 3 Voltage 3.6 4.2 5.5
FIGURE 24-69:
TYPICAL FVR CHANGE VS. TEMPERATURE NORMALIZED AT 25C
1.5 1 0.5 0 -0.5 -1 -1.5 -2 -2.5 -3 -40 0 45 Temperature (C) 85 125
2010 Microchip Technology Inc.
Percent Change (%)
DS41417A-page 261
PIC16F/LF722A/723A
NOTES:
DS41417A-page 262
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
25.0
25.1
PACKAGING INFORMATION
Package Marking Information
28-Lead SPDIP
XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN
Example
PIC16F722A -I/SP e3 0810017
28-Lead QFN/UQFN
Example
XXXXXXXX XXXXXXXX YYWWNNN
16F722A -I/ML e3 0810017
28-Lead SOIC
XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX YYWWNNN
Example
PIC16F722A -I/SO e3 0810017
28-Lead SSOP XXXXXXXXXXXX XXXXXXXXXXXX YYWWNNN
Example PIC16F722A -I/SS e3 0810017
Legend: XX...X Y YY WW NNN
e3
* Note:
Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.
*
Standard PICmicro(R) device marking consists of Microchip part number, year code, week code and traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price.
2010 Microchip Technology Inc.
DS41417A-page 263
PIC16F/LF722A/723A
25.2 Package Details
The following sections give the technical details of the packages.
/HDG 6NLQQ\ 3ODVWLF 'XDO ,Q/LQH 63 PLO %RG\ >63',3@
1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWSZZZPLFURFKLSFRPSDFNDJLQJ
N NOTE 1 E1
1
23 D E
A
A2 L c
A1
b1 b e eB
8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 7RS WR 6HDWLQJ 3ODQH 0ROGHG 3DFNDJH 7KLFNQHVV %DVH WR 6HDWLQJ 3ODQH 6KRXOGHU WR 6KRXOGHU :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK 7LS WR 6HDWLQJ 3ODQH /HDG 7KLFNQHVV 8SSHU /HDG :LGWK /RZHU /HDG :LGWK 2YHUDOO 5RZ 6SDFLQJ 1 H $ $ $ ( ( ' / F E E H% 0,1
,1&+(6 120 %6& 0$;
1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG SHU VLGH 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( <0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS41417A-page 264
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
/HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ [ PP %RG\ >4)1@ ZLWK PP &RQWDFW /HQJWK
1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D D2
EXPOSED PAD
e E E2 2 1 2 1 N NOTE 1 TOP VIEW BOTTOM VIEW L K b
N
A
A3
A1
8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 6WDQGRII &RQWDFW 7KLFNQHVV 2YHUDOO :LGWK ([SRVHG 3DG :LGWK 2YHUDOO /HQJWK ([SRVHG 3DG /HQJWK &RQWDFW :LGWK &RQWDFW /HQJWK 1 H $ $ $ ( ( ' ' E / 0,1 0,//,0(7(56 120 %6& 5() %6& %6& 0$;
&RQWDFWWR([SRVHG 3DG . 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 3DFNDJH LV VDZ VLQJXODWHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( <0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
2010 Microchip Technology Inc.
DS41417A-page 265
PIC16F/LF722A/723A
/HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ [ PP %RG\ >4)1@ ZLWK PP &RQWDFW /HQJWK
1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWSZZZPLFURFKLSFRPSDFNDJLQJ
DS41417A-page 266
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
2010 Microchip Technology Inc.
DS41417A-page 267
PIC16F/LF722A/723A
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
DS41417A-page 268
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
/HDG 3ODVWLF 6PDOO 2XWOLQH 62 :LGH PP %RG\ >62,&@
1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D N
E E1 NOTE 1 123 e b h h c
A
A2
L A1 L1
8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK &KDPIHU RSWLRQDO )RRW /HQJWK )RRWSULQW )RRW $QJOH 7RS /HDG 7KLFNQHVV /HDG :LGWK 0ROG 'UDIW $QJOH 7RS 0ROG 'UDIW $QJOH %RWWRP 1 H $ $ $ ( ( ' K / / I F E D E 0,1
0,//,0(7(56 120 %6& %6& %6& %6& 5() 0$;
1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG PP SHU VLGH 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( <0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
2010 Microchip Technology Inc.
DS41417A-page 269
PIC16F/LF722A/723A
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
DS41417A-page 270
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
/HDG 3ODVWLF 6KULQN 6PDOO 2XWOLQH 66 PP %RG\ >6623@
1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D N
E E1
12 NOTE 1 b e
c A A2 L1
8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK )RRW /HQJWK )RRWSULQW /HDG 7KLFNQHVV )RRW $QJOH /HDG :LGWK 1 H $ $ $ ( ( ' / / F I E 0,1 0,//,0(7(56 120 %6& 5() 0$;
A1
L
1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG PP SHU VLGH 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( <0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
2010 Microchip Technology Inc.
DS41417A-page 271
PIC16F/LF722A/723A
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
DS41417A-page 272
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
APPENDIX A: DATA SHEET REVISION HISTORY APPENDIX B: MIGRATING FROM OTHER PIC(R) DEVICES
Revision A (April 2010)
Original release of this data sheet.
This discusses some of the issues in migrating from other PIC(R) devices to the PIC16F722A/723A family of devices. Note: This device has been designed to perform to the parameters of its data sheet. It has been tested to an electrical specification designed to determine its conformance with these parameters. Due to process differences in the manufacture of this device, this device may have different performance characteristics than its ealier version. These differences may cause this device to perform differently in your application than the earlier version of this device.
Note:
The user should verify that the device oscillator starts and performs as expected. Adjusting the loading capacitor values and/or the oscillator mode may be required.
B.1
PIC16F77 to PIC16F722A/723A
FEATURE COMPARISON
PIC16F77 20 MHz 8K 368 8-bit 2/1 4 Y RB<7:0> RB<7:4> 0 Y N N None N PIC16F722A/ 723A 20 MHz 4K 192 8-bit 2/1 8 Y RB<7:0> RB<7:0> 0 Y N N 500 kHz 16 MHz N
TABLE B-1:
Feature
Max. Operating Speed Max. Program Memory (Words) Max. SRAM (Bytes) A/D Resolution Timers (8/16-bit) Oscillator Modes Brown-out Reset Internal Pull-ups Interrupt-on-change Comparator USART Extended WDT Software Control Option of WDT/BOR INTOSC Frequencies Clock Switching
2010 Microchip Technology Inc.
DS41417A-page 273
PIC16F/LF722A/723A
NOTES:
DS41417A-page 274
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
INDEX
A
A/D Specifications............................................................ 218 Absolute Maximum Ratings .............................................. 199 AC Characteristics Industrial and Extended ............................................ 210 Load Conditions ........................................................ 209 ADC .................................................................................... 87 Acquisition Requirements ........................................... 94 Associated registers.................................................... 96 Block Diagram............................................................. 87 Calculating Acquisition Time....................................... 94 Channel Selection....................................................... 88 Configuration............................................................... 88 Configuring Interrupt ................................................... 91 Conversion Clock........................................................ 88 Conversion Procedure ................................................ 91 Internal Sampling Switch (RSS) IMPEDANCE ................ 94 Interrupts..................................................................... 90 Operation .................................................................... 90 Operation During Sleep .............................................. 90 Port Configuration ....................................................... 88 Reference Voltage (VREF)........................................... 88 Source Impedance...................................................... 94 Special Event Trigger.................................................. 90 ADCON0 Register......................................................... 19, 92 ADCON1 Register......................................................... 20, 93 Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART)............................... 133 ADRES Register ........................................................... 19, 93 Alternate Pin Function......................................................... 47 Analog-to-Digital Converter. See ADC ANSELA Register ............................................................... 49 ANSELB Register ............................................................... 58 APFCON Register......................................................... 20, 47 Assembler MPASM Assembler................................................... 196 AUSART ........................................................................... 133 Associated Registers Baud Rate Generator........................................ 144 Asynchronous Mode ................................................. 135 Associated Registers Receive..................................................... 141 Transmit.................................................... 137 Baud Rate Generator (BRG) ............................ 144 Receiver............................................................ 138 Setting up 9-bit Mode with Address Detect....... 140 Transmitter........................................................ 135 Baud Rate Generator (BRG) Baud Rate Error, Calculating ............................ 144 Baud Rates, Asynchronous Modes .................. 145 Formulas ........................................................... 144 High Baud Rate Select (BRGH Bit) .................. 144 Synchronous Master Mode ............................... 147, 151 Associated Registers Receive..................................................... 150 Transmit.................................................... 148 Reception.......................................................... 149 Transmission .................................................... 147 Synchronous Slave Mode Associated Registers Receive..................................................... 152 Transmit.................................................... 151 Reception ......................................................... 152 Transmission .................................................... 151
B
BF bit ........................................................................ 163, 175 Block Diagram Capacitive Sensing................................................... 117 Block Diagrams (CCP) Capture Mode Operation ............................... 125 ADC ............................................................................ 87 ADC Transfer Function............................................... 95 Analog Input Model..................................................... 95 AUSART Receive ..................................................... 134 AUSART Transmit .................................................... 133 CCP PWM ................................................................ 129 Clock Source .............................................................. 77 Compare................................................................... 127 Crystal Operation........................................................ 81 External RC Mode ...................................................... 82 Interrupt Logic............................................................. 37 MCLR Circuit .............................................................. 29 On-Chip Reset Circuit................................................. 27 PIC16F/LF722A/723A ................................................ 10 RA0 Pins..................................................................... 51 RA4 Pin ...................................................................... 52 RA5 Pin ...................................................................... 53 RA6 Pin ...................................................................... 54 RA7 Pin ...................................................................... 54 RB0 Pin ...................................................................... 60 RB3 Pin ...................................................................... 62 RB4, RB2, RB1 Pins................................................... 61 RB5 Pin ...................................................................... 63 RB6 Pin ...................................................................... 64 RB7 Pin ...................................................................... 65 RC0 Pin ...................................................................... 69 RC1 Pin ...................................................................... 69 RC2 Pin ...................................................................... 70 RC3 Pin ...................................................................... 70 RC4 Pin ...................................................................... 71 RC5 Pin ...................................................................... 71 RC6 Pin ...................................................................... 72 RC7 Pin ...................................................................... 72 RE3 Pin ...................................................................... 75 Resonator Operation .................................................. 82 SPI Mode.................................................................. 156 SSP (I2C Mode)........................................................ 165 Timer1 .............................................. 103, 109, 110, 111 Timer2 ...................................................................... 115 TMR0/WDT Prescaler ................................................ 99 Brown-out Reset (BOR)...................................................... 31 Specifications ........................................................... 216 Timing and Characteristics ....................................... 215
C
C Compilers MPLAB C18.............................................................. 196 Capacitive Sensing ........................................................... 117 Associated registers w/ Capacitive Sensing............. 122 Capture Module. See Capture/Compare/PWM (CCP) Capture/Compare/PWM (CCP) ........................................ 123 Associated registers w/ Capture............................... 126 Associated registers w/ Compare............................. 128 Associated registers w/ PWM................................... 132 Capture Mode........................................................... 125
2010 Microchip Technology Inc.
DS41417A-page 275
PIC16F/LF722A/723A
CCPx Pin Configuration ............................................ 125 Compare Mode ......................................................... 127 CCPx Pin Configuration .................................... 127 Software Interrupt Mode ........................... 125, 127 Special Event Trigger........................................ 127 Timer1 Mode Selection ............................. 125, 127 Interaction of Two CCP Modules (table) ................... 123 Prescaler ................................................................... 125 PWM Mode ............................................................... 129 Duty Cycle......................................................... 130 Effects of Reset................................................. 131 Example PWM Frequencies and Resolutions, 20 MHZ ................................ 131 Example PWM Frequencies and Resolutions, 8 MHz................................... 131 Operation in Sleep Mode .................................. 131 Setup for Operation........................................... 131 System Clock Frequency Changes................... 131 PWM Period .............................................................. 130 Setup for PWM Operation ......................................... 131 Timer Resources....................................................... 123 CCP. See Capture/Compare/PWM (CCP) CCP1CON Register ............................................................ 19 CCP2CON Register ............................................................ 19 CCPR1H Register ............................................................... 19 CCPR1L Register................................................................ 19 CCPR2H Register ............................................................... 19 CCPR2L Register................................................................ 19 CCPxCON Register .......................................................... 124 CKE bit ...................................................................... 163, 175 CKP bit ...................................................................... 162, 174 Clock Sources External Modes ........................................................... 81 EC ....................................................................... 81 HS ....................................................................... 81 LP........................................................................ 81 OST..................................................................... 81 RC....................................................................... 82 XT ....................................................................... 81 Code Examples A/D Conversion ........................................................... 91 Changing Between Capture Prescalers .................... 125 Indirect Addressing ..................................................... 26 Initializing PORTA ....................................................... 48 Initializing PORTB ....................................................... 56 Initializing PORTC....................................................... 67 Initializing PORTE ....................................................... 74 Loading the SSPBUF (SSPSR) Register .................. 158 Saving W, STATUS and PCLATH Registers in RAM ................................................................ 39 Comparators C2OUT as T1 Gate ................................................... 106 Compare Module. See Capture/Compare/PWM (CCP) CONFIG1 Register........................................................ 83, 84 CPSCON0 Register .......................................................... 121 CPSCON1 Register .......................................................... 122 Customer Change Notification Service ............................. 281 Customer Notification Service........................................... 281 Customer Support ............................................................. 281 Extended and Industrial ............................................ 206 Industrial and Extended ............................................ 200 Development Support ....................................................... 195 Device Configuration .......................................................... 83 Code Protection .......................................................... 85 Configuration Word..................................................... 83 User ID ....................................................................... 85 Device Overview................................................................... 9
E
Effects of Reset PWM mode ............................................................... 131 Electrical Specifications .................................................... 199 Enhanced Capture/Compare/PWM (ECCP) Specifications ........................................................... 217 Errata .................................................................................... 8
F
Firmware Instructions ....................................................... 185 Fixed Voltage Reference. See FVR FSR Register ................................................................ 19, 20 Fuses. See Configuration Bits FVR..................................................................................... 97 FVRCON Register ........................................................ 20, 97
G
General Purpose Register File ........................................... 16
I
I2C Mode Associated Registers ................................................ 176 INDF Register ............................................................... 19, 20 Indirect Addressing, INDF and FSR Registers ................... 26 Instruction Format............................................................. 185 Instruction Set................................................................... 185 ADDLW..................................................................... 187 ADDWF..................................................................... 187 ANDLW..................................................................... 187 ANDWF..................................................................... 187 MOVF ....................................................................... 190 BCF .......................................................................... 187 BSF........................................................................... 187 BTFSC ...................................................................... 187 BTFSS ...................................................................... 188 CALL......................................................................... 188 CLRF ........................................................................ 188 CLRW ....................................................................... 188 CLRWDT .................................................................. 188 COMF ....................................................................... 188 DECF ........................................................................ 188 DECFSZ ................................................................... 189 GOTO ....................................................................... 189 INCF ......................................................................... 189 INCFSZ..................................................................... 189 IORLW ...................................................................... 189 IORWF...................................................................... 189 MOVLW .................................................................... 190 MOVWF .................................................................... 190 NOP .......................................................................... 190 RETFIE ..................................................................... 191 RETLW ..................................................................... 191 RETURN................................................................... 191 RLF ........................................................................... 192 RRF .......................................................................... 192 SLEEP ...................................................................... 192 SUBLW ..................................................................... 192
D
D/A bit ............................................................................... 175 Data Memory....................................................................... 16 Data/Address bit (D/A) ...................................................... 175 DC and AC Characteristics ............................................... 227 DC Characteristics
DS41417A-page 276
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
SUBWF ..................................................................... 193 SWAPF ..................................................................... 193 XORLW..................................................................... 193 XORWF..................................................................... 193 Summary Table......................................................... 186 INTCON Register ................................................................ 40 Internal Oscillator Block INTOSC Specifications.................................................... 213 Internal Sampling Switch (RSS) IMPEDANCE ........................ 94 Internet Address................................................................ 281 Interrupts ............................................................................. 37 ADC ............................................................................ 91 Associated registers w/ Interrupts............................... 44 Interrupt-on-Change.................................................... 56 TMR1 ........................................................................ 108 INTOSC Specifications ..................................................... 213 IOCB Register ..................................................................... 58 Computed GOTO ....................................................... 25 Stack........................................................................... 25 PCL Register ................................................................ 19, 20 PCLATH Register ......................................................... 19, 20 PCON Register ....................................................... 20, 24, 32 PIE1 Register ............................................................... 20, 41 PIE2 Register ............................................................... 20, 42 Pin Diagram PIC16F/LF722A/723A, 28-pin PDIP/SOIC/SSOP/QFN/ UQFN ................................................................... 5 Pinout Descriptions PIC16F722A/723A...................................................... 11 PIR1 Register ............................................................... 19, 43 PIR2 Register ............................................................... 19, 44 PMADRH Register............................................................ 179 PMADRL Register ............................................................ 179 PMCON1 Register .............................................. 21, 178, 179 PMDATH Register ............................................................ 178 PMDATL Register............................................................. 178 PORTA ............................................................................... 48 ANSELA Register ....................................................... 49 Associated Registers.................................................. 55 Pin Descriptions and Diagrams .................................. 50 PORTA Register......................................................... 19 RA0............................................................................. 50 RA1............................................................................. 50 RA2............................................................................. 50 RA3............................................................................. 50 RA4............................................................................. 50 RA5............................................................................. 50 RA6............................................................................. 50 RA7............................................................................. 50 Specifications ........................................................... 214 PORTA Register ................................................................. 48 PORTB ............................................................................... 56 Additional Pin Functions ANSELB Register ............................................... 56 Weak Pull-up ...................................................... 56 Associated Registers.................................................. 66 Interrupt-on-Change ................................................... 56 P1B/P1C/P1D.See Enhanced Capture/Compare/ PWM+ (ECCP+) ................................................. 56 Pin Descriptions and Diagrams .................................. 59 PORTB Register......................................................... 19 RB0............................................................................. 59 RB1............................................................................. 59 RB2............................................................................. 59 RB3............................................................................. 59 RB4............................................................................. 59 RB5............................................................................. 59 RB6............................................................................. 59 RB7............................................................................. 59 PORTB Register ................................................................. 57 PORTC ............................................................................... 67 Associated Registers.................................................. 73 P1A.See Enhanced Capture/Compare/PWM+ (ECCP+) ............................................................. 67 PORTC Register......................................................... 19 RC0 ............................................................................ 68 RC2 ............................................................................ 68 RC3 ............................................................................ 68 RC4 ............................................................................ 68 RC5 ............................................................................ 68 RC6 ............................................................................ 68 RC7 ............................................................................ 68
L
Load Conditions ................................................................ 209
M
MCLR .................................................................................. 29 Internal ........................................................................ 29 Memory Organization.......................................................... 15 Data ............................................................................ 16 Program ...................................................................... 15 Microchip Internet Web Site .............................................. 281 Migrating from other PIC Microcontroller Devices............. 273 MPLAB ASM30 Assembler, Linker, Librarian ................... 196 MPLAB Integrated Development Environment Software .. 195 MPLAB PM3 Device Programmer .................................... 198 MPLAB REAL ICE In-Circuit Emulator System................. 197 MPLINK Object Linker/MPLIB Object Librarian ................ 196
O
OPCODE Field Descriptions ............................................. 185 OPTION Register ................................................................ 23 OPTION_REG Register .................................................... 101 OSCCON Register .............................................................. 79 Oscillator Associated registers............................................ 82, 114 Oscillator Module EC ............................................................................... 77 HS ............................................................................... 77 INTOSC ...................................................................... 77 INTOSCIO................................................................... 77 LP................................................................................ 77 Oscillator Tuning ......................................................... 80 RC............................................................................... 77 RCIO ........................................................................... 77 XT ............................................................................... 77 Oscillator Parameters ....................................................... 213 Oscillator Specifications .................................................... 212 Oscillator Start-up Timer (OST) Specifications............................................................ 216 OSCTUNE Register ............................................................ 80
P
P (Stop) bit ........................................................................ 175 Packaging ......................................................................... 263 Marking ..................................................................... 263 PDIP Details.............................................................. 264 Paging, Program Memory ................................................... 25 PCL and PCLATH ............................................................... 25
2010 Microchip Technology Inc.
DS41417A-page 277
PIC16F/LF722A/723A
Specifications ............................................................ 214 PORTC Register ................................................................. 67 PORTE................................................................................ 74 Associated Registers .................................................. 74 PORTE Register ......................................................... 19 RE0 ............................................................................. 75 RE3 ............................................................................. 75 PORTE Register ................................................................. 74 Power-Down Mode (Sleep) ............................................... 181 Associated Registers ................................................ 182 Power-on Reset .................................................................. 29 Power-up Timer (PWRT)..................................................... 29 Specifications ............................................................ 216 PR2 Register............................................................... 20, 164 Precision Internal Oscillator Parameters........................... 213 Prescaler Shared WDT/Timer0 ................................................. 100 Product Identification System............................................ 283 Program Memory ................................................................ 15 Map and Stack (PIC16F/LF722A) ............................... 15 Map and Stack (PIC16F/LF723A) ............................... 15 Paging ......................................................................... 25 Program Memory Read (PMR) ......................................... 177 Associated Registers ................................................ 179 Programming, Device Instructions .................................... 185 PORTE ....................................................................... 74 RCSTA (Receive Status and Control) ...................... 143 Reset Values .............................................................. 34 Reset Values (Special Registers) ............................... 36 Special Function Register Map PIC16F/LF723A.................................................. 18 Special Function, Summary........................................ 19 SSPCON (Sync Serial Port Control) Register .. 162, 174 SSPSTAT (Sync Serial Port Status) Register... 163, 175 STATUS ..................................................................... 22 T1CON (Timer1 Control) .......................................... 112 T1GCON (Timer1 Gate Control)............................... 113 T2CON ..................................................................... 116 TRISA (Tri-State PORTA)........................................... 48 TRISB (Tri-State PORTB)........................................... 57 TRISC (Tri-State PORTC) .......................................... 67 TRISE (Tri-State PORTE)........................................... 74 TXSTA (Transmit Status and Control) ...................... 142 WPUB (Weak Pull-up PORTB)................................... 57 Reset .................................................................................. 27 Resets Associated Registers .................................................. 36 Revision History................................................................ 273
S
S (Start) bit........................................................................ 175 SMP bit ..................................................................... 163, 175 Software Simulator (MPLAB SIM) .................................... 197 SPBRG ............................................................................. 144 SPBRG Register................................................................. 20 Special Event Trigger ......................................................... 90 Special Function Registers ................................................. 16 Special Function Registers (SFRs)..................................... 19 SPI Mode .......................................................................... 161 Associated Registers ................................................ 164 Typical Master/Slave Connection ............................. 155 SSP................................................................................... 155 I2C Mode .................................................................. 165 Acknowledge .................................................... 166 Addressing........................................................ 167 Clock Stretching ............................................... 172 Clock Synchronization ...................................... 173 Firmware Master Mode..................................... 172 Hardware Setup................................................ 165 Multi-Master Mode............................................ 172 Reception ......................................................... 168 Sleep Operation................................................ 173 Start/Stop Conditions........................................ 166 Transmission .................................................... 170 Master Mode............................................................. 157 SPI Mode .................................................................. 155 Slave Mode....................................................... 159 Typical SPI Master/Slave Connection ...................... 155 SSPADD Register............................................................... 20 SSPBUF Register ............................................................... 19 SSPCON Register .............................................. 19, 162, 174 SSPEN bit................................................................. 162, 174 SSPM bits ................................................................. 162, 174 SSPMSK Register .............................................................. 20 SSPOV bit................................................................. 162, 174 SSPSTAT Register ............................................. 20, 163, 175 STATUS Register ............................................................... 22 Synchronous Serial Port Enable bit (SSPEN) .......... 162, 174 Synchronous Serial Port Mode Select bits (SSPM).. 162, 174
R
R/W bit .............................................................................. 175 RCREG ............................................................................. 140 RCREG Register................................................................. 19 RCSTA Register.......................................................... 19, 143 Reader Response ............................................................. 282 Read-Modify-Write Operations.......................................... 185 Receive Overflow Indicator bit (SSPOV)................... 162, 174 Registers ADCON0 (ADC Control 0) .......................................... 92 ADCON1 (ADC Control 1) .......................................... 93 ADRES (ADC Result) ................................................. 93 ANSELA (PORTA Analog Select) ............................... 49 ANSELB (PORTB Analog Select) ............................... 58 APFCON (Alternate Pin Function Control).................. 47 CCPxCON (CCP Operation) ..................................... 124 CONFIG1 (Configuration Word Register 1) .......... 83, 84 CPSCON0 (Capacitive Sensing Control Register 0). 121 CPSCON1 (Capacitive Sensing Control Register 1). 122 FVRCON (Fixed Voltage Reference Register) ........... 97 INTCON (Interrupt Control) ......................................... 40 IOCB (Interrupt-on-Change PORTB) .......................... 58 OPTION_REG (OPTION) ........................................... 23 OPTION_REG (Option) ............................................ 101 OSCCON (Oscillator Control) ..................................... 79 OSCTUNE (Oscillator Tuning) .................................... 80 PCON (Power Control Register) ................................. 24 PCON (Power Control) ............................................... 32 PIE1 (Peripheral Interrupt Enable 1) ........................... 41 PIE2 (Peripheral Interrupt Enable 2) ........................... 42 PIR1 (Peripheral Interrupt Register 1) ........................ 43 PIR2 (Peripheral Interrupt Request 2) ........................ 44 PMADRH (Program Memory Address High)............. 179 PMADRL (Program Memory Address Low) .............. 179 PMCON1 (Program Memory Control 1) .................... 178 PMDATH (Program Memory Data High)................... 178 PMDATL (Program Memory Data Low) .................... 178 PORTA........................................................................ 48 PORTB........................................................................ 57 PORTC ....................................................................... 67
DS41417A-page 278
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
T
T1CON Register ......................................................... 19, 112 TMR1ON Bit.............................................................. 113 T1GCON Register............................................................. 113 T2CON Register ................................................. 19, 116, 164 Thermal Considerations .................................................... 208 Time-out Sequence............................................................. 32 Timer0 ................................................................................. 99 Associated Registers ................................................ 101 Interrupt..................................................................... 101 Operation ............................................................ 99, 104 Specifications............................................................ 217 Timer1 ............................................................................... 103 Associated registers.................................................. 114 Asynchronous Counter Mode ................................... 105 Reading and Writing ......................................... 105 Interrupt..................................................................... 108 Modes of Operation .................................................. 104 Module On/Off (TMR1ON Bit)................................... 113 Operation During Sleep ............................................ 108 Oscillator ................................................................... 105 Prescaler................................................................... 105 Specifications............................................................ 217 Timer1 Gate Selecting Source............................................... 106 TMR1H Register ....................................................... 103 TMR1L Register........................................................ 103 Timer2 Associated registers.................................................. 116 Timers Timer1 T1CON.............................................................. 112 T1GCON ........................................................... 113 Timer2 T2CON.............................................................. 116 Timing Diagrams A/D Conversion......................................................... 219 A/D Conversion (Sleep Mode) .................................. 219 Asynchronous Reception .......................................... 140 Asynchronous Transmission..................................... 136 Asynchronous Transmission (Back-to-Back) ............ 136 Brown-out Reset (BOR) ............................................ 215 Brown-out Reset Situations ........................................ 31 CLKOUT and I/O....................................................... 213 Clock Synchronization .............................................. 173 Clock Timing ............................................................. 210 Enhanced Capture/Compare/PWM (ECCP) ............. 217 I2C Bus Data ............................................................. 224 I2C Bus Start/Stop Bits.............................................. 223 I2C Reception (7-bit Address) ................................... 168 I2C Slave Mode with SEN = 0 (Reception, 10-bit Address) ................................................. 169 I2C Transmission (7-bit Address).............................. 170 INT Pin Interrupt.......................................................... 38 Reset, WDT, OST and Power-up Timer ................... 214 Slave Select Synchronization ................................... 161 SPI Master Mode ...................................................... 158 SPI Master Mode (CKE = 1, SMP = 1) ..................... 221 SPI Mode (Slave Mode with CKE = 0) ...................... 160 SPI Mode (Slave Mode with CKE = 1) ...................... 160 SPI Slave Mode (CKE = 0) ....................................... 222 SPI Slave Mode (CKE = 1) ....................................... 222 Synchronous Reception (Master Mode, SREN) ....... 150 Synchronous Transmission....................................... 148 Synchronous Transmission (Through TXEN) ........... 148 Time-out Sequence Case 1 ................................................................ 33 Case 2 ................................................................ 33 Case 3 ................................................................ 33 Timer0 and Timer1 External Clock ........................... 216 Timer1 Incrementing Edge ....................................... 108 USART Synchronous Receive (Master/Slave) ......... 220 USART Synchronous Transmission (Master/Slave). 220 Wake-up from Interrupt............................................. 182 Timing Parameter Symbology .......................................... 209 Timing Requirements I2C Bus Data............................................................. 225 I2C Bus Start/Stop Bits............................................. 224 SPI Mode.................................................................. 223 TMR0 Register.................................................................... 19 TMR1H Register ................................................................. 19 TMR1L Register.................................................................. 19 TMR2 Register.................................................................... 19 TMRO Register................................................................... 21 TRISA ................................................................................. 48 TRISA Register............................................................. 20, 48 TRISB ................................................................................. 56 TRISB Register............................................................. 20, 57 TRISC ................................................................................. 67 TRISC Register............................................................. 20, 67 TRISE ................................................................................. 74 TRISE Register............................................................. 20, 74 TXREG ............................................................................. 135 TXREG Register ................................................................. 19 TXSTA Register.......................................................... 20, 142 BRGH Bit .................................................................. 144
U
UA..................................................................................... 175 Update Address bit, UA .................................................... 175 USART Synchronous Master Mode Requirements, Synchronous Receive .............. 220 Requirements, Synchronous Transmission...... 220 Timing Diagram, Synchronous Receive ........... 220 Timing Diagram, Synchronous Transmission... 220
V
VREF. SEE ADC Reference Voltage
W
Wake-up Using Interrupts ................................................. 182 Watchdog Timer (WDT)...................................................... 29 Clock Source .............................................................. 29 Period ......................................................................... 29 Specifications ........................................................... 216 WCOL bit .................................................................. 162, 174 WPUB Register................................................................... 57 Write Collision Detect bit (WCOL) ............................ 162, 174 WWW Address ................................................................. 281 WWW, On-Line Support ....................................................... 8
2010 Microchip Technology Inc.
DS41417A-page 279
PIC16F/LF722A/723A
NOTES:
DS41417A-page 280
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels: * * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions.
2010 Microchip Technology Inc.
DS41417A-page 281
PIC16F/LF722A/723A
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: RE: Technical Publications Manager Reader Response Total Pages Sent ________
From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y N Literature Number: DS41417A FAX: (______) _________ - _________
Device: PIC16F/LF722A/723A Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS41417A-page 282
2010 Microchip Technology Inc.
PIC16F/LF722A/723A
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X Temperature Range /XX Package XXX Pattern Examples: a) PIC16F722A-E/SP 301 = Extended Temp., skinny PDIP package, QTP pattern #301 PIC16F722A-I/SO = Industrial Temp., SOIC package
Device:
PIC16F722A, PIC16LF722A, PIC16F722AT, PIC16LF722AT(1) PIC16F723A, PIC16LF723A, PIC16F723AT, PIC16LF723AT(1) I E MV ML SO SP SS = -40C to+85C = -40C to+125C = = = = = Micro Lead Frame (UQFN) Micro Lead Frame (QFN) SOIC Skinny Plastic DIP SSOP
b)
Temperature Range: Package:
Note1:
T
= In tape and reel.
Pattern:
3-Digit Pattern Code for QTP (blank otherwise)
2010 Microchip Technology Inc.
DS41417A-page 283
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350
EUROPE
Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820
01/05/10
DS41417A-page 284
2010 Microchip Technology Inc.

▲Up To Search▲

Price & Availability of PIC16F722A-EMV

	To Download PIC16F722A-EMV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .